[PATCH V4 4/8] phy: st-miphy-40lp: Add skeleton driver
Kishon Vijay Abraham I
kishon at ti.com
Thu Feb 6 01:23:20 EST 2014
Hi,
On Thursday 06 February 2014 11:44 AM, Pratyush Anand wrote:
> Hi Kishon,
>
> On Thu, Feb 06, 2014 at 02:01:45PM +0800, Kishon Vijay Abraham I wrote:
>> Hi,
>>
>> On Thursday 06 February 2014 10:14 AM, Pratyush Anand wrote:
>>> ST miphy-40lp supports PCIe, SATA and Super Speed USB. This driver adds
>>> skeleton support for the same.
>>>
>>> Currently phy ops are returning -EINVAL. They can be elaborated
>>> depending on the SOC being supported in future.
>>>
>>> Signed-off-by: Pratyush Anand <pratyush.anand at st.com>
>>> Tested-by: Mohit Kumar <mohit.kumar at st.com>
>>> Cc: Arnd Bergmann <arnd at arndb.de>
>>> Cc: Kishon Vijay Abraham I <kishon at ti.com>
>>> Cc: spear-devel at list.st.com
>>> Cc: linux-arm-kernel at lists.infradead.org
>>> Cc: devicetree at vger.kernel.org
>>> Cc: linux-kernel at vger.kernel.org
>>> ---
>>> .../devicetree/bindings/phy/st-miphy40lp.txt | 12 ++
>>> drivers/phy/Kconfig | 6 +
>>> drivers/phy/Makefile | 1 +
>>> drivers/phy/phy-miphy40lp.c | 174 +++++++++++++++++++++
>>> 4 files changed, 193 insertions(+)
>>> create mode 100644 Documentation/devicetree/bindings/phy/st-miphy40lp.txt
>>> create mode 100644 drivers/phy/phy-miphy40lp.c
>>>
>>> diff --git a/Documentation/devicetree/bindings/phy/st-miphy40lp.txt b/Documentation/devicetree/bindings/phy/st-miphy40lp.txt
>>> new file mode 100644
>>> index 0000000..d0c7096
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/phy/st-miphy40lp.txt
>>> @@ -0,0 +1,12 @@
>>> +Required properties:
>>> +- compatible : should be "st,miphy40lp-phy"
>>> + Other supported soc specific compatible:
>>> + "st,spear1310-miphy"
>>> + "st,spear1340-miphy"
>>> +- reg : offset and length of the PHY register set.
>>> +- misc: phandle for the syscon node to access misc registers
>>> +- phy-id: Instance id of the phy.
>>> +- #phy-cells : from the generic PHY bindings, must be 1.
>>> + - 1st cell: phandle to the phy node.
>>> + - 2nd cell: 0 if phy (in 1st cell) is to be used for SATA, 1 for PCIe
>>> + and 2 for Super Speed USB.
>>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
>>> index afa2354..2f58993 100644
>>> --- a/drivers/phy/Kconfig
>>> +++ b/drivers/phy/Kconfig
>>> @@ -64,4 +64,10 @@ config BCM_KONA_USB2_PHY
>>> help
>>> Enable this to support the Broadcom Kona USB 2.0 PHY.
>>>
>>> +config PHY_ST_MIPHY40LP
>>> + tristate "ST MIPHY 40LP driver"
>>> + help
>>> + Support for ST MIPHY 40LP which can be used for PCIe, SATA and Super Speed USB.
>>> + select GENERIC_PHY
>>> +
>>> endmenu
>>> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
>>> index b57c253..c061091 100644
>>> --- a/drivers/phy/Makefile
>>> +++ b/drivers/phy/Makefile
>>> @@ -9,3 +9,4 @@ obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO) += phy-exynos-mipi-video.o
>>> obj-$(CONFIG_PHY_MVEBU_SATA) += phy-mvebu-sata.o
>>> obj-$(CONFIG_OMAP_USB2) += phy-omap-usb2.o
>>> obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o
>>> +obj-$(CONFIG_PHY_ST_MIPHY40LP) += phy-miphy40lp.o
>>> diff --git a/drivers/phy/phy-miphy40lp.c b/drivers/phy/phy-miphy40lp.c
>>> new file mode 100644
>>> index 0000000..d478c14
>>> --- /dev/null
>>> +++ b/drivers/phy/phy-miphy40lp.c
>>> @@ -0,0 +1,174 @@
>>> +/*
>>> + * ST MiPHY-40LP PHY driver
>>> + *
>>> + * Copyright (C) 2014 ST Microelectronics
>>> + * Pratyush Anand <pratyush.anand at st.com>
>>> + *
>>> + * This program is free software; you can redistribute it and/or modify
>>> + * it under the terms of the GNU General Public License version 2 as
>>> + * published by the Free Software Foundation.
>>> + *
>>> + */
>>> +
>>> +#include <linux/delay.h>
>>> +#include <linux/dma-mapping.h>
>>> +#include <linux/kernel.h>
>>> +#include <linux/mfd/syscon.h>
>>> +#include <linux/module.h>
>>> +#include <linux/of_device.h>
>>> +#include <linux/phy/phy.h>
>>> +#include <linux/regmap.h>
>>> +
>>> +enum phy_mode {
>>> + SATA,
>>> + PCIE,
>>> + SS_USB,
>>> +};
>>> +
>>> +struct st_miphy40lp_priv {
>>> + /* regmap for any soc specific misc registers */
>>> + struct regmap *misc;
>>> + /* phy struct pointer */
>>> + struct phy *phy;
>>> + /* device node pointer */
>>> + struct device_node *np;
>>> + /* phy mode: 0 for SATA 1 for PCIe and 2 for SS-USB */
>>> + enum phy_mode mode;
>>> + /* instance id of this phy */
>>> + u32 id;
>>> +};
>>> +
>>> +static int miphy40lp_init(struct phy *phy)
>>> +{
>>> + return -EINVAL;
>>> +}
>>> +
>>> +static int miphy40lp_exit(struct phy *phy)
>>> +{
>>> + return -EINVAL;
>>> +}
>>> +
>>> +static int miphy40lp_power_off(struct phy *phy)
>>> +{
>>> + return -EINVAL;
>>> +}
>>> +
>>> +static int miphy40lp_power_on(struct phy *phy)
>>> +{
>>> + return -EINVAL;
>>> +}
>>> +
>>> +static const struct of_device_id st_miphy40lp_of_match[] = {
>>> + { .compatible = "st,miphy40lp-phy" },
>>> + { },
>>> +};
>>> +MODULE_DEVICE_TABLE(of, st_miphy40lp_of_match);
>>> +
>>> +static struct phy_ops st_miphy40lp_ops = {
>>> + .init = miphy40lp_init,
>>> + .exit = miphy40lp_exit,
>>> + .power_off = miphy40lp_power_off,
>>> + .power_on = miphy40lp_power_on,
>>> + .owner = THIS_MODULE,
>>
>> Would prefer to either align all the fields or align none. Here only owner is
>> aligned.
>
> ok.
>
>>> +};
>>> +
>>> +#ifdef CONFIG_PM_SLEEP
>>> +static int miphy40lp_suspend(struct device *dev)
>>> +{
>>> + return -EINVAL;
>>> +}
>>> +
>>> +static int miphy40lp_resume(struct device *dev)
>>> +{
>>> + return -EINVAL;
>>> +}
>>> +#endif
>>> +
>>> +static SIMPLE_DEV_PM_OPS(miphy40lp_pm_ops, miphy40lp_suspend,
>>> + miphy40lp_resume);
>>> +
>>> +static struct phy *st_miphy40lp_xlate(struct device *dev,
>>> + struct of_phandle_args *args)
>>> +{
>>> + struct st_miphy40lp_priv *phypriv = dev_get_drvdata(dev);
>>> +
>>> + if (args->args_count < 1) {
>>> + dev_err(dev, "DT did not pass correct no of args\n");
>>> + return NULL;
>>> + }
>>> +
>>> + phypriv->mode = args->args[0];
>>> +
>>> + return phypriv->phy;
>>> +}
>>> +
>>> +static int __init st_miphy40lp_probe(struct platform_device *pdev)
>>> +{
>>> + struct device *dev = &pdev->dev;
>>> + struct st_miphy40lp_priv *phypriv;
>>> + struct phy_provider *phy_provider;
>>> +
>>> + phypriv = devm_kzalloc(dev, sizeof(*phypriv), GFP_KERNEL);
>>> + if (!phypriv) {
>>> + dev_err(dev, "can't alloc miphy40lp private date memory\n");
>>> + return -ENOMEM;
>>> + }
>>> +
>>> + phypriv->np = dev->of_node;
>>> +
>>> + phypriv->misc =
>>> + syscon_regmap_lookup_by_phandle(dev->of_node, "misc");
>>> + if (IS_ERR(phypriv->misc)) {
>>> + dev_err(dev, "failed to find misc regmap\n");
>>> + return PTR_ERR(phypriv->misc);
>>> + }
>>> +
>>> + if (of_property_read_u32(dev->of_node, "phy-id", &phypriv->id)) {
>>> + dev_err(dev, "failed to find phy id\n");
>>> + return -EINVAL;
>>> + }
>> Do we really need this phy id? How is it being used?
>
> Yes , it is being used by patch 6/8.
Alright.
>
>>
>>> +
>>> + phy_provider = devm_of_phy_provider_register(dev, st_miphy40lp_xlate);
>>> + if (IS_ERR(phy_provider)) {
>>> + dev_err(dev, "failed to register phy provider\n");
>>> + return PTR_ERR(phy_provider);
>>> + }
>>
>> phy_provider_register should be the last step in registering the PHY. Or your
>> PHY call backs can be called before you create the PHY. Btw in your case you
>
> But every one else like phy-exynos-mipi-video or phy-omap-usb2 or any
> other did it same way. First phy_provider_register and then
> phy_create.
That's a bug which we figured out very late. Will get it fixed in this -rc cycle.
Thanks
Kishon
More information about the linux-arm-kernel
mailing list