[PATCH 1/3] clk: rcar-h2: fix sd0/sd1 divisor table

[Ben Dooks]

On 05/02/14 11:55, Ben Dooks wrote:
> On 05/02/14 10:56, Laurent Pinchart wrote:
>> Hi William,
>>
>> Thank you for the patch.
>>
>> On Tuesday 04 February 2014 18:17:36 William Towle wrote:
>>> The clk_div_table for cpg_sd01_div_table[] concurs with the manual
>>> but not with values found in the device itself (which are also the
>>> same as the ones in arch/arm/mach-shmobile/clock-r8a7790.c).
>>>
>>> Update the clk-rcar-gen2.c driver to have the same table as the one
>>> used by the mach-shmobile driver which work once further issues are
>>> fixed in the clk-rcar-gen2.c driver.
>>>
>>> Part of the fix for the following error where the driver reports the
>>> output as 1MHz but is really 97.5MHz:
>>>      sh_mobile_sdhi ee100000.sd: mmc0 base at 0xee100000 clock rate 1
>>> MHz
>>>
>>> [ben.dooks at codethink.co.uk: updated patch description]
>>> Signed-off-by: William Towle <william.towle at codethink.co.uk>
>>> Reviewed-by: Ben Dooks <ben.dooks at codethink.co.uk>
>>> ---
>>>   drivers/clk/shmobile/clk-rcar-gen2.c |    2 ++
>>>   1 file changed, 2 insertions(+)
>>>
>>> diff --git a/drivers/clk/shmobile/clk-rcar-gen2.c
>>> b/drivers/clk/shmobile/clk-rcar-gen2.c index a59ec21..df4a1e6 100644
>>> --- a/drivers/clk/shmobile/clk-rcar-gen2.c
>>> +++ b/drivers/clk/shmobile/clk-rcar-gen2.c
>>> @@ -170,6 +170,8 @@ static const struct clk_div_table
>>> cpg_sdh_div_table[] =
>>> { };
>>>
>>>   static const struct clk_div_table cpg_sd01_div_table[] = {
>>> +    {  0,  2 }, {  1,  3 }, {  2,  4 }, {  3,  6 },
>>> +    {  4,  8 },
>>>       {  5, 12 }, {  6, 16 }, {  7, 18 }, {  8, 24 },
>>>       { 10, 36 }, { 11, 48 }, { 12, 10 }, {  0,  0 },
>>
>> With this applied the only difference between the sdh and sd0/1 dividers
>> tables would be the { 12, 10 } entry, available for sd0/1 only. Given
>> that the
>> hardware does not match the documentation, could you check whether
>> that entry
>> is supported by sdh as well ? If so we could merge the two tables.
>> Otherwise
>> this patch looks good, could you please just reformat the table to
>> avoid the
>> mostly empty line in the middle ?
>
> I would like feedback from Renesas on this issue if possible. I can
> have a quick try at setting the clock value to 10 in u-boot and scope
> it out and see what happens.
>
> Magnus or Morimoto-san, is there a chance this could be reviewed by
> someone in Renesas who has knowledge of the hardware block?
>
> [PS, added Kuninori Morimoto to this[

I got William to do a quick test with the following u-boot command
	mw.l 0xE6150074 0xCCC

sdhi0 showed 156MHz output, and it seemed to work. So there is a
distinct possibility that the sdh clock also supports setting 12
for a /10

-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius