[RFC PATCHv2 0/7] devfreq: Add devfreq-event class to provide raw data for devfreq device

[Chanwoo Choi]

Hi Krzysztof,

On 12/10/2014 10:21 PM, Chanwoo Choi wrote:
> Hi Krzysztof,
> 
> On Wed, Dec 10, 2014 at 7:07 PM, Krzysztof Kozlowski
> <k.kozlowski at samsung.com> wrote:
>> On wto, 2014-12-09 at 23:12 +0900, Chanwoo Choi wrote:
>>> This patchset add new devfreq_event class to provide raw data to determine
>>> current utilization of device  which is used for devfreq governor.
>>>
>>> [Description of devfreq-event class]
>>> This patchset add new devfreq_event class for devfreq_event device which provide
>>> raw data (e.g., memory bus utilization/GPU utilization). This raw data from
>>> devfreq_event data would be used for the governor of devfreq subsystem.
>>> - devfreq_event device : Provide raw data for governor of existing devfreq device
>>> - devfreq device       : Monitor device state and change frequency/voltage of device
>>>                          using the raw data from devfreq_event device
>>>
>>> The devfreq subsystem support generic DVFS(Dynamic Voltage/Frequency Scaling)
>>> for Non-CPU Devices. The devfreq device would dertermine current device state
>>> using various governor (e.g., ondemand, performance, powersave). After completed
>>> determination of system state, devfreq device would change the frequency/voltage
>>> of devfreq device according to the result of governor.
>>>
>>> But, devfreq governor must need basic data which indicates current device state.
>>> Existing devfreq subsystem only consider devfreq device which check current system
>>> state and determine proper system state using basic data. There is no subsystem
>>> for device providing basic data to devfreq device.
>>>
>>> The devfreq subsystem must need devfreq_event device(data-provider device) for
>>> existing devfreq device. So, this patch add new devfreq_event class for
>>> devfreq_event device which read various basic data(e.g, memory bus utilization,
>>> GPU utilization) and provide measured data to existing devfreq device through
>>> standard APIs of devfreq_event class.
>>>
>>> The following description explains the feature of two kind of devfreq class:
>>> - devfreq class (existing)
>>>  : devfreq consumer device use raw data from devfreq_event device for
>>>    determining proper current system state and change voltage/frequency
>>>    dynamically using various governors.
>>> - devfreq_event class (new)
>>>  : Provide measured raw data to devfreq device for governor
>>>
>>> Also, the devfreq-event device would support various type event as following:
>>>  : DEVFREQ_EVENT_TYPE_RAW_DATA
>>>  : DEVFREQ_EVENT_TYPE_UTILIZATION
>>>  : DEVFREQ_EVENT_TYPE_BANDWIDTH
>>>  : DEVFREQ_EVENT_TYPE_LATENCY
>>>
>>> [For example]
>>> If board dts includes PPMU_DMC0/DMC1/CPU event node,
>>> would show following sysfs entry. Also devfreq driver(e.g., exynos4_bus.c)
>>> can get the instance of devfreq-event device by using provided API and then
>>> get raw data which reflect the current state of device.
>>>
>>
>> Hi,
>>
>> Overall I like the idea. I understand that now devfreq devices (like
>> exynos devfreq) should bind themselves to buses, not to PPMU. It makes
>> sense to me because bus clock and bus voltage are properties of bus, not
>> monitoring unit.
>>
>> I see that this is still a RFC so it would be hard to base current
>> devfreq work on top of it.
> 
> The goal of this patch set is not for devfreq device. This patch set
> just is used for
> devfreq-event device according to patch description.
> 
> The devfreq must need devfreq-event device (e.g., exynos-ppmu.c)
> but current devfreq subsystem have not been supported any reason for
> exyons-ppmu.c as devfreq-event device.
> 
> I discussed this same issue on following patch[1] which was posted to support
> exynos4 busfreq by me.
> [1] https://lkml.org/lkml/2014/3/14/132
> - [PATCHv2 8/8] devfreq: exynos4: Add busfreq driver for exynos4210/exynos4x12
> After discussion, I thought that devfreq-event class must be needed
> before supporting
> the dt of devfreq device.
> 
> So, I think that devfreq have to support the devfreq-event subsystem
> for exynos-ppmu. And then I'll work to support the device-tree of devfreq device
> as next job.
> 
>>
>> One more general comment: you're adding a some API which is not used by
>> current devfreq_event user (exynos). For example the exclusive flag or
>> event types. I think it will be simpler to stick to the basic approach
>> (reduced API). If some other user emerges then new API will be added.
> 
> I think that devfreq-event must support both event_flag(e.g., exclusive flag)
> and event_type(e.g., raw_data, utilization, bandwidth, latency) because
> devfreq-event device (e.g., exynos-ppmu) would provide various event data.
> For example, exynos-ppmu driver could support the utilization/bandwidth/latency
> of each IP of Exynos SoC. I checked PPMU IP on Exynos TRM.
> 
> Also, If specific devfreq-event device should be used on only one device driver,
> devfrewq-event class have to support 'exclusive' flag. If
> devfreq-event class don't
> support the exclusive flag, devfreq-event could not guarantee the
> integrity of event
> from devfreq-event device.

I'll drop 'exclusive' flag according to your comment.

Thanks for your review.

Best Regards,
Chanwoo Choi