[PATCH V2 1/2] ARM: dts: Add DT changes for display on snow

[Ajay kumar]

On Thu, Aug 28, 2014 at 2:45 PM, Mark Rutland <mark.rutland at arm.com> wrote:
> On Thu, Aug 28, 2014 at 06:34:33AM +0100, Ajay kumar wrote:
>> On Wed, Aug 27, 2014 at 8:31 PM, Mark Rutland <mark.rutland at arm.com> wrote:
>> > On Wed, Aug 27, 2014 at 03:48:27PM +0100, Ajay Kumar wrote:
>> >> Add DT nodes for ptn3460 bridge chip and panel.
>> >> Add backlight enable pin and backlight power supply for pwm-backlight.
>> >> Also add bridge phandle needed by dp to enable display on snow.
>> >>
>> >> Note that, snow doesn't support "chunghwa,claa101wb01" panel,
>> >> but still we choose to reuse the binding since "chunghwa,claa101wb01"
>> >> has similar LCD timings.
>> >
>> > What does it actually have?
>> >
>> > It's fine to have "chunghwa,claa101wb01" as a fallback but we should
>> > have an identifier for the actual display, too.
>> Actual display used is "AUO,B116XTN0", for which no data currently exists
>> in panel file. Instead of adding a new panel_desc for B116XTN0,
>> why not we reuse existing ones? what is the "identifier" you are talking about?
>
> The compatible string.
>
> So in the dts we'd have compatible = "au0,b116xtn0", "chunghwa,claa101wb01";
Sorry, hardware engineer says actual LCD name is "auo,b116xw03".

> That way if we need specific data we can add it later.
I think we can add a new panel_desc for "auo,b116xw03".
Because its actual LCD dimension is 256x144, but "chungwa, claa101wb01" has
LCD dimension 223x125.
What is Thierry's opinion on adding this new LCD?

> What vendor is AU0? Can we add a vendor-prefix in parallel?
its "auo" (already present: AU Optronics Corporation)

Ajay

> Thanks,
> Mark.
>
>>
>> Ajay
>> > Thanks,
>> > Mark.
>> >
>> >> Signed-off-by: Ajay Kumar <ajaykumar.rs at samsung.com>
>> >> ---
>> >> Changes since V1:
>> >>       -- Remove "simple-panel" compatible string.
>> >>       -- Use GPIO_ACTIVE_HIGH instead of 0.
>> >>       -- Change panel node naming from "panel-simple" to "panel".
>> >>
>> >>  arch/arm/boot/dts/exynos5250-snow.dts |   41 ++++++++++++++++++---------------
>> >>  1 file changed, 22 insertions(+), 19 deletions(-)
>> >>
>> >> diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
>> >> index f2b8c41..1ac9709 100644
>> >> --- a/arch/arm/boot/dts/exynos5250-snow.dts
>> >> +++ b/arch/arm/boot/dts/exynos5250-snow.dts
>> >> @@ -9,6 +9,7 @@
>> >>  */
>> >>
>> >>  /dts-v1/;
>> >> +#include <dt-bindings/gpio/gpio.h>
>> >>  #include "exynos5250.dtsi"
>> >>  #include "exynos5250-cros-common.dtsi"
>> >>
>> >> @@ -181,7 +182,7 @@
>> >>                                       dcdc3 {
>> >>                                               ti,enable-ext-control;
>> >>                                       };
>> >> -                                     fet1 {
>> >> +                                     fet1: fet1 {
>> >>                                               regulator-name = "vcd_led";
>> >>                                               ti,overcurrent-wait = <3>;
>> >>                                       };
>> >> @@ -204,7 +205,7 @@
>> >>                                               regulator-always-on;
>> >>                                               ti,overcurrent-wait = <3>;
>> >>                                       };
>> >> -                                     fet6 {
>> >> +                                     fet6: fet6 {
>> >>                                               regulator-name = "lcd_vdd";
>> >>                                               ti,overcurrent-wait = <3>;
>> >>                                       };
>> >> @@ -253,6 +254,15 @@
>> >>                       pinctrl-0 = <&max98095_en>;
>> >>                       pinctrl-names = "default";
>> >>               };
>> >> +
>> >> +             ptn3460: lvds-bridge at 20 {
>> >> +                     compatible = "nxp,ptn3460";
>> >> +                     reg = <0x20>;
>> >> +                     powerdown-gpios = <&gpy2 5 GPIO_ACTIVE_HIGH>;
>> >> +                     reset-gpios = <&gpx1 5 GPIO_ACTIVE_HIGH>;
>> >> +                     edid-emulation = <5>;
>> >> +                     panel = <&panel>;
>> >> +             };
>> >>       };
>> >>
>> >>       i2s0: i2s at 03830000 {
>> >> @@ -300,11 +310,13 @@
>> >>               vdd_pll-supply = <&ldo8_reg>;
>> >>       };
>> >>
>> >> -     backlight {
>> >> +     backlight: backlight {
>> >>               compatible = "pwm-backlight";
>> >>               pwms = <&pwm 0 1000000 0>;
>> >>               brightness-levels = <0 100 500 1000 1500 2000 2500 2800>;
>> >>               default-brightness-level = <7>;
>> >> +             enable-gpios = <&gpx3 0 GPIO_ACTIVE_HIGH>;
>> >> +             power-supply = <&fet1>;
>> >>               pinctrl-0 = <&pwm0_out>;
>> >>               pinctrl-names = "default";
>> >>       };
>> >> @@ -314,6 +326,12 @@
>> >>               samsung,invert-vclk;
>> >>       };
>> >>
>> >> +     panel: panel {
>> >> +             compatible = "chunghwa,claa101wb01";
>> >> +             power-supply = <&fet6>;
>> >> +             backlight = <&backlight>;
>> >> +     };
>> >> +
>> >>       dp-controller at 145B0000 {
>> >>               status = "okay";
>> >>               pinctrl-names = "default";
>> >> @@ -325,22 +343,7 @@
>> >>               samsung,link-rate = <0x0a>;
>> >>               samsung,lane-count = <2>;
>> >>               samsung,hpd-gpio = <&gpx0 7 0>;
>> >> -
>> >> -             display-timings {
>> >> -                     native-mode = <&timing1>;
>> >> -
>> >> -                     timing1: timing at 1 {
>> >> -                             clock-frequency = <70589280>;
>> >> -                             hactive = <1366>;
>> >> -                             vactive = <768>;
>> >> -                             hfront-porch = <40>;
>> >> -                             hback-porch = <40>;
>> >> -                             hsync-len = <32>;
>> >> -                             vback-porch = <10>;
>> >> -                             vfront-porch = <12>;
>> >> -                             vsync-len = <6>;
>> >> -                     };
>> >> -             };
>> >> +             bridge = <&ptn3460>;
>> >>       };
>> >>  };
>> >>
>> >> --
>> >> 1.7.9.5
>> >>
>> >> --
>> >> To unsubscribe from this list: send the line "unsubscribe devicetree" in
>> >> the body of a message to majordomo at vger.kernel.org
>> >> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>> >>
>>