[PATCH V2 1/2] ARM: dts: Add DT changes for display on snow

[Mark Rutland]

On Thu, Aug 28, 2014 at 06:34:33AM +0100, Ajay kumar wrote:
> On Wed, Aug 27, 2014 at 8:31 PM, Mark Rutland <mark.rutland at arm.com> wrote:
> > On Wed, Aug 27, 2014 at 03:48:27PM +0100, Ajay Kumar wrote:
> >> Add DT nodes for ptn3460 bridge chip and panel.
> >> Add backlight enable pin and backlight power supply for pwm-backlight.
> >> Also add bridge phandle needed by dp to enable display on snow.
> >>
> >> Note that, snow doesn't support "chunghwa,claa101wb01" panel,
> >> but still we choose to reuse the binding since "chunghwa,claa101wb01"
> >> has similar LCD timings.
> >
> > What does it actually have?
> >
> > It's fine to have "chunghwa,claa101wb01" as a fallback but we should
> > have an identifier for the actual display, too.
> Actual display used is "AUO,B116XTN0", for which no data currently exists
> in panel file. Instead of adding a new panel_desc for B116XTN0,
> why not we reuse existing ones? what is the "identifier" you are talking about?

The compatible string.

So in the dts we'd have compatible = "au0,b116xtn0", "chunghwa,claa101wb01";

That way if we need specific data we can add it later.

What vendor is AU0? Can we add a vendor-prefix in parallel?

Thanks,
Mark.

> 
> Ajay
> > Thanks,
> > Mark.
> >
> >> Signed-off-by: Ajay Kumar <ajaykumar.rs at samsung.com>
> >> ---
> >> Changes since V1:
> >>       -- Remove "simple-panel" compatible string.
> >>       -- Use GPIO_ACTIVE_HIGH instead of 0.
> >>       -- Change panel node naming from "panel-simple" to "panel".
> >>
> >>  arch/arm/boot/dts/exynos5250-snow.dts |   41 ++++++++++++++++++---------------
> >>  1 file changed, 22 insertions(+), 19 deletions(-)
> >>
> >> diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
> >> index f2b8c41..1ac9709 100644
> >> --- a/arch/arm/boot/dts/exynos5250-snow.dts
> >> +++ b/arch/arm/boot/dts/exynos5250-snow.dts
> >> @@ -9,6 +9,7 @@
> >>  */
> >>
> >>  /dts-v1/;
> >> +#include <dt-bindings/gpio/gpio.h>
> >>  #include "exynos5250.dtsi"
> >>  #include "exynos5250-cros-common.dtsi"
> >>
> >> @@ -181,7 +182,7 @@
> >>                                       dcdc3 {
> >>                                               ti,enable-ext-control;
> >>                                       };
> >> -                                     fet1 {
> >> +                                     fet1: fet1 {
> >>                                               regulator-name = "vcd_led";
> >>                                               ti,overcurrent-wait = <3>;
> >>                                       };
> >> @@ -204,7 +205,7 @@
> >>                                               regulator-always-on;
> >>                                               ti,overcurrent-wait = <3>;
> >>                                       };
> >> -                                     fet6 {
> >> +                                     fet6: fet6 {
> >>                                               regulator-name = "lcd_vdd";
> >>                                               ti,overcurrent-wait = <3>;
> >>                                       };
> >> @@ -253,6 +254,15 @@
> >>                       pinctrl-0 = <&max98095_en>;
> >>                       pinctrl-names = "default";
> >>               };
> >> +
> >> +             ptn3460: lvds-bridge at 20 {
> >> +                     compatible = "nxp,ptn3460";
> >> +                     reg = <0x20>;
> >> +                     powerdown-gpios = <&gpy2 5 GPIO_ACTIVE_HIGH>;
> >> +                     reset-gpios = <&gpx1 5 GPIO_ACTIVE_HIGH>;
> >> +                     edid-emulation = <5>;
> >> +                     panel = <&panel>;
> >> +             };
> >>       };
> >>
> >>       i2s0: i2s at 03830000 {
> >> @@ -300,11 +310,13 @@
> >>               vdd_pll-supply = <&ldo8_reg>;
> >>       };
> >>
> >> -     backlight {
> >> +     backlight: backlight {
> >>               compatible = "pwm-backlight";
> >>               pwms = <&pwm 0 1000000 0>;
> >>               brightness-levels = <0 100 500 1000 1500 2000 2500 2800>;
> >>               default-brightness-level = <7>;
> >> +             enable-gpios = <&gpx3 0 GPIO_ACTIVE_HIGH>;
> >> +             power-supply = <&fet1>;
> >>               pinctrl-0 = <&pwm0_out>;
> >>               pinctrl-names = "default";
> >>       };
> >> @@ -314,6 +326,12 @@
> >>               samsung,invert-vclk;
> >>       };
> >>
> >> +     panel: panel {
> >> +             compatible = "chunghwa,claa101wb01";
> >> +             power-supply = <&fet6>;
> >> +             backlight = <&backlight>;
> >> +     };
> >> +
> >>       dp-controller at 145B0000 {
> >>               status = "okay";
> >>               pinctrl-names = "default";
> >> @@ -325,22 +343,7 @@
> >>               samsung,link-rate = <0x0a>;
> >>               samsung,lane-count = <2>;
> >>               samsung,hpd-gpio = <&gpx0 7 0>;
> >> -
> >> -             display-timings {
> >> -                     native-mode = <&timing1>;
> >> -
> >> -                     timing1: timing at 1 {
> >> -                             clock-frequency = <70589280>;
> >> -                             hactive = <1366>;
> >> -                             vactive = <768>;
> >> -                             hfront-porch = <40>;
> >> -                             hback-porch = <40>;
> >> -                             hsync-len = <32>;
> >> -                             vback-porch = <10>;
> >> -                             vfront-porch = <12>;
> >> -                             vsync-len = <6>;
> >> -                     };
> >> -             };
> >> +             bridge = <&ptn3460>;
> >>       };
> >>  };
> >>
> >> --
> >> 1.7.9.5
> >>
> >> --
> >> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> >> the body of a message to majordomo at vger.kernel.org
> >> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> >>
>