[PATCH v7 01/10] PCI: host: rcar: Add Renesas R-Car PCIe driver

[Bjorn Helgaas]

On Mon, Apr 28, 2014 at 4:03 AM, Phil Edworthy
<phil.edworthy at renesas.com> wrote:
> Hi Bjorn,
>
> Thanks for the review.
>
> On 24 April 2014 20:19, Bjorn wrote:
>> On Mon, Mar 31, 2014 at 11:30:46AM +0100, Phil Edworthy wrote:
>> > This PCIe Host driver currently does not support MSI, so cards
>> > fall back to INTx interrupts.
>> >
>> > Signed-off-by: Phil Edworthy <phil.edworthy at renesas.com>
>> > ...
>>
>> > --- /dev/null
>> > +++ b/drivers/pci/host/pcie-rcar.c
>> > @@ -0,0 +1,693 @@
>> > ...
>> > +#include <linux/slab.h>
>> > +#include "pcie-rcar.h"
>>
>> It looks like the things in pcie-rcar.h are used only in this file
>> (pcie-rcar.c), so you might as well just put the contents here and not have
>> a pcie-rcar.h at all.  Of course, if there are things needed by more than
>> one file, they should stay in pcie-rcar.h.
> Nothing else uses them so I'll put in the c file.
>
>> > +#define DRV_NAME "rcar-pcie"
>> > +
>> > +#define RCONF(x)   (PCICONF(0)+(x))
>> > +#define RPMCAP(x)  (PMCAP(0)+(x))
>> > +#define REXPCAP(x) (EXPCAP(0)+(x))
>> > +#define RVCCAP(x)  (VCCAP(0)+(x))
>> > +
>> > +#define  PCIE_CONF_BUS(b)  (((b) & 0xff) << 24)
>> > +#define  PCIE_CONF_DEV(d)  (((d) & 0x1f) << 19)
>> > +#define  PCIE_CONF_FUNC(f) (((f) & 0x7) << 16)
>> > +
>> > +#define PCI_MAX_RESOURCES 4
>> > +#define MAX_NR_INBOUND_MAPS 6
>> > +
>> > +/* Structure representing the PCIe interface */
>> > +struct rcar_pcie {
>> > +   struct device           *dev;
>> > +   void __iomem            *base;
>> > +   struct resource         res[PCI_MAX_RESOURCES];
>> > +   u8                      root_bus_nr;
>>
>> I don't understand how root_bus_nr works.  From its name, it sounds like
>> it's the bus number of the PCI bus on the downstream side of the host
>> bridge.
> That's correct.
>
>> That bus number should be a property of the host bridge, i.e.,
>> it's either hard-wired into the bridge, or it's programmable somewhere.
>> But root_bus_nr comes from sys->busnr, which is apparently from some
>> generic code that knows nothing about this particular host bridge.
> The manual for this hardware says that the HW doesn't care what the bus number
> is set to. The only thing the HW needs to know is that when sending config
> accesses, we need to indicate whether it's a TYPE0 or TYPE1 header; so we use
> root_bus_nr to determine this. The generic code that sets up sys->busnr (ARM
> bios32 in this case), just increments bus number for each controller.
>
> This is very similar to the pcie-designware driver, in dw_pcie_scan_bus().

OK.  From what you said below, it sounds like you would add a DT entry
for the bus range you want to have below this bridge, and use TYPE0
accesses for the base of that range.

I'm not sure how you reconcile this with the idea that the bios32 code
just increments a bus number for each controller.

>> > +static int __init rcar_pcie_get_resources(struct platform_device *pdev,
>> > +   struct rcar_pcie *pcie)
>> > +{
>> > +   struct resource res;
>> > +   int err;
>> > +
>> > +   err = of_address_to_resource(pdev->dev.of_node, 0, &res);
>> > +   if (err)
>> > +           return err;
>>
>> I don't see anywhere that figures out the bus number range behind this host
>> bridge.  The PCI core needs to know this.  I know the core assumes 00-ff if
>> it's not supplied, but that's just to deal with the legacy situation where
>> we assumed one host bridge was all anybody would ever need.
>>
>> For new code, we should be explicit about the range.
> This means add a DT entry for bus-range, and simply calling pci_add_resource for
> the range, right? If so, ok.

Yeah, I guess.  If the HW really doesn't look at the bus number at
all, it sounds like the range is effectively 00-ff, and each host
bridge should be in its own domain.

Bjorn