[PATCH v2 08/10] ARM: EXYNOS: Refactored code for using PMU address via DT
Tomasz Figa
tomasz.figa at gmail.com
Fri Apr 25 15:19:05 PDT 2014
Hi,
On 25.04.2014 14:32, Pankaj Dubey wrote:
> Under "arm/mach-exynos" many files are using PMU register offsets.
> Since we have added support for accessing PMU base address via DT,
> now we can remove PMU mapping from exynosX_iodesc.
> Let's convert all these access using either of "get_exynos_pmuaddr"
> or "get_exynos_regmap".
> This will help us in removing static mapping of PMU base address
> as well as help in reducing dependency over machine header files.
> Thus helping for migration of PMU implementation from machine to driver
> folder which can be reused for ARM64 bsed SoC.
>
> Signed-off-by: Pankaj Dubey <pankaj.dubey at samsung.com>
> ---
> arch/arm/mach-exynos/common.h | 4 +-
> arch/arm/mach-exynos/cpuidle.c | 37 ++-
> arch/arm/mach-exynos/exynos.c | 19 +-
> arch/arm/mach-exynos/hotplug.c | 4 +-
> arch/arm/mach-exynos/include/mach/map.h | 3 -
> arch/arm/mach-exynos/platsmp.c | 13 +-
> arch/arm/mach-exynos/pm.c | 60 ++--
> arch/arm/mach-exynos/pmu.c | 40 +--
> arch/arm/mach-exynos/regs-pmu.h | 506 +++++++++++++++----------------
> 9 files changed, 348 insertions(+), 338 deletions(-)
>
> diff --git a/arch/arm/mach-exynos/common.h b/arch/arm/mach-exynos/common.h
> index ecfd0fc..ad5128e 100644
> --- a/arch/arm/mach-exynos/common.h
> +++ b/arch/arm/mach-exynos/common.h
> @@ -40,7 +40,7 @@ extern void exynos_cpu_die(unsigned int cpu);
>
> /* PMU(Power Management Unit) support */
>
> -#define PMU_TABLE_END NULL
> +#define PMU_TABLE_END 0xFFFF
IMHO (-1U) would be more appropriate.
>
> enum sys_powerdown {
> SYS_AFTR,
> @@ -51,7 +51,7 @@ enum sys_powerdown {
>
> extern unsigned long l2x0_regs_phys;
> struct exynos_pmu_conf {
> - void __iomem *reg;
> + unsigned int offset;
> unsigned int val[NUM_SYS_POWERDOWN];
> };
>
> diff --git a/arch/arm/mach-exynos/cpuidle.c b/arch/arm/mach-exynos/cpuidle.c
> index c57cae0..5dcdd46 100644
> --- a/arch/arm/mach-exynos/cpuidle.c
> +++ b/arch/arm/mach-exynos/cpuidle.c
> @@ -17,6 +17,7 @@
> #include <linux/module.h>
> #include <linux/time.h>
> #include <linux/platform_device.h>
> +#include <linux/regmap.h>
>
> #include <asm/proc-fns.h>
> #include <asm/smp_scu.h>
> @@ -34,10 +35,10 @@
>
> #define REG_DIRECTGO_ADDR (samsung_rev() == EXYNOS4210_REV_1_1 ? \
> S5P_INFORM7 : (samsung_rev() == EXYNOS4210_REV_1_0 ? \
> - (S5P_VA_SYSRAM + 0x24) : S5P_INFORM0))
> + 0x24 : S5P_INFORM0))
> #define REG_DIRECTGO_FLAG (samsung_rev() == EXYNOS4210_REV_1_1 ? \
> S5P_INFORM6 : (samsung_rev() == EXYNOS4210_REV_1_0 ? \
> - (S5P_VA_SYSRAM + 0x20) : S5P_INFORM1))
> + 0x20 : S5P_INFORM1))
This patch seems to be based on old code, before Daniel Lezcano's Exynos
cpuidle refactor [1] and it should be rebased on top of that series.
[1] http://thread.gmane.org/gmane.linux.kernel.samsung-soc/29085
>
> #define S5P_CHECK_AFTR 0xFCBA0D10
>
> @@ -60,6 +61,8 @@
> #define PWR_CTRL2_CORE2_UP_RATIO (1 << 4)
> #define PWR_CTRL2_CORE1_UP_RATIO (1 << 0)
>
> +static struct regmap *pmu_regmap;
> +
> static int exynos4_enter_lowpower(struct cpuidle_device *dev,
> struct cpuidle_driver *drv,
> int index);
> @@ -87,7 +90,7 @@ static struct cpuidle_driver exynos4_idle_driver = {
> /* Ext-GIC nIRQ/nFIQ is the only wakeup source in AFTR */
> static void exynos4_set_wakeupmask(void)
> {
> - __raw_writel(0x0000ff3e, S5P_WAKEUP_MASK);
> + regmap_write(pmu_regmap, S5P_WAKEUP_MASK, 0x0000ff3e);
> }
>
> static unsigned int g_pwr_ctrl, g_diag_reg;
> @@ -120,22 +123,28 @@ static int exynos4_enter_core0_aftr(struct cpuidle_device *dev,
> struct cpuidle_driver *drv,
> int index)
> {
> - unsigned long tmp;
> + unsigned int tmp;
>
> exynos4_set_wakeupmask();
>
> /* Set value of power down register for aftr mode */
> exynos_sys_powerdown_conf(SYS_AFTR);
> -
> - __raw_writel(virt_to_phys(exynos_cpu_resume), REG_DIRECTGO_ADDR);
> - __raw_writel(S5P_CHECK_AFTR, REG_DIRECTGO_FLAG);
> -
> +
> + if (samsung_rev() == EXYNOS4210_REV_1_0) {
> + __raw_writel(virt_to_phys(exynos_cpu_resume),
> + S5P_VA_SYSRAM + REG_DIRECTGO_ADDR);
> + __raw_writel(S5P_CHECK_AFTR, S5P_VA_SYSRAM + REG_DIRECTGO_FLAG);
> + } else {
> + regmap_write(pmu_regmap, REG_DIRECTGO_ADDR,
> + virt_to_phys(exynos_cpu_resume));
> + regmap_write(pmu_regmap, REG_DIRECTGO_FLAG, S5P_CHECK_AFTR);
> + }
This is quite ugly. I'd refactor this into a function pointer set once
at initialization time depending on SoC type and create two functions
for both cases.
In general, please also see my comments about this kind of code checking
SoC type posted as a part of my review of Vikas' Exynos5260 PMU support
series [2].
[2] http://thread.gmane.org/gmane.linux.kernel.samsung-soc/28056/focus=29342
> save_cpu_arch_register();
>
> /* Setting Central Sequence Register for power down mode */
> - tmp = __raw_readl(S5P_CENTRAL_SEQ_CONFIGURATION);
> + regmap_read(pmu_regmap, S5P_CENTRAL_SEQ_CONFIGURATION, &tmp);
> tmp &= ~S5P_CENTRAL_LOWPWR_CFG;
> - __raw_writel(tmp, S5P_CENTRAL_SEQ_CONFIGURATION);
> + regmap_write(pmu_regmap, S5P_CENTRAL_SEQ_CONFIGURATION, tmp);
>
> cpu_pm_enter();
> cpu_suspend(0, idle_finisher);
> @@ -154,14 +163,14 @@ static int exynos4_enter_core0_aftr(struct cpuidle_device *dev,
> * S5P_CENTRAL_LOWPWR_CFG bit will not be set automatically
> * in this situation.
> */
> - tmp = __raw_readl(S5P_CENTRAL_SEQ_CONFIGURATION);
> + regmap_read(pmu_regmap, S5P_CENTRAL_SEQ_CONFIGURATION, &tmp);
> if (!(tmp & S5P_CENTRAL_LOWPWR_CFG)) {
> tmp |= S5P_CENTRAL_LOWPWR_CFG;
> - __raw_writel(tmp, S5P_CENTRAL_SEQ_CONFIGURATION);
> + regmap_write(pmu_regmap, S5P_CENTRAL_SEQ_CONFIGURATION, tmp);
> }
>
> /* Clear wakeup state register */
> - __raw_writel(0x0, S5P_WAKEUP_STAT);
> + regmap_write(pmu_regmap, S5P_WAKEUP_STAT, 0x0);
>
> return index;
> }
> @@ -219,6 +228,8 @@ static int exynos_cpuidle_probe(struct platform_device *pdev)
> int cpu_id, ret;
> struct cpuidle_device *device;
>
> + pmu_regmap = get_exynos_pmuregmap();
Why couldn't you simply look for PMU node here and then call
syscon_regmap_lookup_by_phandle()? (You will have to anyway, as Daniel's
patches mentioned above move the driver to drivers/cpuidle and it is not
possible to include headers and it is not allowed to include mach/
headers from drivers/.)
> +
> if (soc_is_exynos5250())
> exynos5_core_down_clk();
>
> diff --git a/arch/arm/mach-exynos/exynos.c b/arch/arm/mach-exynos/exynos.c
> index 68f60e1..b01987e 100644
> --- a/arch/arm/mach-exynos/exynos.c
> +++ b/arch/arm/mach-exynos/exynos.c
> @@ -20,6 +20,7 @@
> #include <linux/platform_device.h>
> #include <linux/pm_domain.h>
> #include <linux/mfd/syscon.h>
> +#include <linux/regmap.h>
>
> #include <asm/cacheflush.h>
> #include <asm/hardware/cache-l2x0.h>
> @@ -67,11 +68,6 @@ static struct map_desc exynos4_iodesc[] __initdata = {
> .length = SZ_4K,
> .type = MT_DEVICE,
> }, {
> - .virtual = (unsigned long)S5P_VA_PMU,
> - .pfn = __phys_to_pfn(EXYNOS4_PA_PMU),
> - .length = SZ_64K,
> - .type = MT_DEVICE,
> - }, {
> .virtual = (unsigned long)S5P_VA_COMBINER_BASE,
> .pfn = __phys_to_pfn(EXYNOS4_PA_COMBINER),
> .length = SZ_4K,
> @@ -195,11 +191,6 @@ static struct map_desc exynos5_iodesc[] __initdata = {
> .pfn = __phys_to_pfn(EXYNOS5_PA_CMU),
> .length = 144 * SZ_1K,
> .type = MT_DEVICE,
> - }, {
> - .virtual = (unsigned long)S5P_VA_PMU,
> - .pfn = __phys_to_pfn(EXYNOS5_PA_PMU),
> - .length = SZ_64K,
> - .type = MT_DEVICE,
> },
> };
>
> @@ -207,7 +198,7 @@ static void exynos_restart(enum reboot_mode mode, const char *cmd)
> {
> struct device_node *np;
> u32 val = 0x1;
> - void __iomem *addr = EXYNOS_SWRESET;
> + void __iomem *addr = NULL;
>
> if (of_machine_is_compatible("samsung,exynos5440")) {
> u32 status;
> @@ -220,9 +211,9 @@ static void exynos_restart(enum reboot_mode mode, const char *cmd)
> val = __raw_readl(addr);
>
> val = (val & 0xffff0000) | (status & 0xffff);
> - }
> -
> - __raw_writel(val, addr);
> + __raw_writel(val, addr);
> + } else
> + regmap_write(exynos_pmu_regmap, EXYNOS_SWRESET, val);
> }
>
> static struct platform_device exynos_cpuidle = {
> diff --git a/arch/arm/mach-exynos/hotplug.c b/arch/arm/mach-exynos/hotplug.c
> index 73b0b5c..7831e64 100644
> --- a/arch/arm/mach-exynos/hotplug.c
> +++ b/arch/arm/mach-exynos/hotplug.c
> @@ -13,6 +13,7 @@
> #include <linux/errno.h>
> #include <linux/smp.h>
> #include <linux/io.h>
> +#include <linux/regmap.h>
>
> #include <asm/cacheflush.h>
> #include <asm/cp15.h>
> @@ -91,11 +92,12 @@ static inline void cpu_leave_lowpower(void)
>
> static inline void platform_do_lowpower(unsigned int cpu, int *spurious)
> {
> + struct regmap *pmu_base = get_exynos_pmuregmap();
pmu_base is rather unfortunate name for a variable holding a pointer to
a regmap, still...
> for (;;) {
>
> /* make cpu1 to be turned off at next WFI command */
> if (cpu == 1)
> - __raw_writel(0, S5P_ARM_CORE1_CONFIGURATION);
> + regmap_write(pmu_base, S5P_ARM_CORE1_CONFIGURATION, 0);
...inside mach-exynos you could probably define exynos_pmu_write() that
would call regmap_write() with exynos_pmu_regmap (after making it
non-static) directly. This way the old code wouldn't have to care about
the regmap at all, just __raw_writel() would be replaced with
exynos_pmu_write().
OR
In case of registers that are known to not need sharing between multiple
drivers, the mapped area could be used directly. This would probably let
you eliminate any regmap-specific code from mach-exynos.
>
> /*
> * here's the WFI
> diff --git a/arch/arm/mach-exynos/include/mach/map.h b/arch/arm/mach-exynos/include/mach/map.h
> index 7b046b5..1ba7fb5 100644
> --- a/arch/arm/mach-exynos/include/mach/map.h
> +++ b/arch/arm/mach-exynos/include/mach/map.h
> @@ -35,9 +35,6 @@
> #define EXYNOS4_PA_SYSCON 0x10010000
> #define EXYNOS5_PA_SYSCON 0x10050100
>
> -#define EXYNOS4_PA_PMU 0x10020000
> -#define EXYNOS5_PA_PMU 0x10040000
> -
> #define EXYNOS4_PA_CMU 0x10030000
> #define EXYNOS5_PA_CMU 0x10010000
>
> diff --git a/arch/arm/mach-exynos/platsmp.c b/arch/arm/mach-exynos/platsmp.c
> index 29c2286..9ce4c9f9 100644
> --- a/arch/arm/mach-exynos/platsmp.c
> +++ b/arch/arm/mach-exynos/platsmp.c
> @@ -31,11 +31,12 @@
> #include "regs-pmu.h"
>
> extern void exynos4_secondary_startup(void);
> +static void __iomem *pmu_base;
>
> static inline void __iomem *cpu_boot_reg_base(void)
> {
> if (soc_is_exynos4210() && samsung_rev() == EXYNOS4210_REV_1_1)
> - return S5P_INFORM5;
> + return pmu_base + S5P_INFORM5;
> return S5P_VA_SYSRAM;
> }
>
> @@ -106,14 +107,14 @@ static int exynos_boot_secondary(unsigned int cpu, struct task_struct *idle)
> */
> write_pen_release(phys_cpu);
>
> - if (!(__raw_readl(S5P_ARM_CORE1_STATUS) & S5P_CORE_LOCAL_PWR_EN)) {
> + if (!(__raw_readl(pmu_base + S5P_ARM_CORE1_STATUS)
> + & S5P_CORE_LOCAL_PWR_EN)) {
> __raw_writel(S5P_CORE_LOCAL_PWR_EN,
> - S5P_ARM_CORE1_CONFIGURATION);
> -
> + pmu_base + S5P_ARM_CORE1_CONFIGURATION);
> timeout = 10;
>
> /* wait max 10 ms until cpu1 is on */
> - while ((__raw_readl(S5P_ARM_CORE1_STATUS)
> + while ((__raw_readl(pmu_base + S5P_ARM_CORE1_STATUS)
> & S5P_CORE_LOCAL_PWR_EN) != S5P_CORE_LOCAL_PWR_EN) {
> if (timeout-- == 0)
> break;
> @@ -201,6 +202,8 @@ static void __init exynos_smp_prepare_cpus(unsigned int max_cpus)
> {
> int i;
>
> + pmu_base = get_exynos_pmuaddr();
> +
> if (read_cpuid_part_number() == ARM_CPU_PART_CORTEX_A9)
> scu_enable(scu_base_addr());
>
> diff --git a/arch/arm/mach-exynos/pm.c b/arch/arm/mach-exynos/pm.c
> index 723c988..e4c10d4 100644
> --- a/arch/arm/mach-exynos/pm.c
> +++ b/arch/arm/mach-exynos/pm.c
> @@ -20,6 +20,7 @@
> #include <linux/irqchip/arm-gic.h>
> #include <linux/err.h>
> #include <linux/clk.h>
> +#include <linux/regmap.h>
>
> #include <asm/cacheflush.h>
> #include <asm/hardware/cache-l2x0.h>
> @@ -37,6 +38,8 @@
> #include "regs-pmu.h"
> #include "regs-sys.h"
>
> +static struct regmap *pmu_regmap;
> +
> /**
> * struct exynos_wkup_irq - Exynos GIC to PMU IRQ mapping
> * @hwirq: Hardware IRQ signal of the GIC
> @@ -125,43 +128,44 @@ static void exynos_pm_prepare(void)
> unsigned int tmp;
>
> /* Set wake-up mask registers */
> - __raw_writel(exynos_get_eint_wake_mask(), S5P_EINT_WAKEUP_MASK);
> - __raw_writel(exynos_irqwake_intmask & ~(1 << 31), S5P_WAKEUP_MASK);
> + regmap_write(pmu_regmap, S5P_EINT_WAKEUP_MASK,
> + exynos_get_eint_wake_mask());
> + regmap_write(pmu_regmap, S5P_WAKEUP_MASK,
> + exynos_irqwake_intmask & ~(1 << 31));
>
> s3c_pm_do_save(exynos_core_save, ARRAY_SIZE(exynos_core_save));
>
> if (soc_is_exynos5250()) {
> s3c_pm_do_save(exynos5_sys_save, ARRAY_SIZE(exynos5_sys_save));
> /* Disable USE_RETENTION of JPEG_MEM_OPTION */
> - tmp = __raw_readl(EXYNOS5_JPEG_MEM_OPTION);
> + regmap_read(pmu_regmap, EXYNOS5_JPEG_MEM_OPTION, &tmp);
> tmp &= ~EXYNOS5_OPTION_USE_RETENTION;
> - __raw_writel(tmp, EXYNOS5_JPEG_MEM_OPTION);
> + regmap_write(pmu_regmap, EXYNOS5_JPEG_MEM_OPTION, tmp);
> }
>
> /* Set value of power down register for sleep mode */
>
> exynos_sys_powerdown_conf(SYS_SLEEP);
> - __raw_writel(S5P_CHECK_SLEEP, S5P_INFORM1);
> + regmap_write(pmu_regmap, S5P_INFORM1, S5P_CHECK_SLEEP);
>
> /* ensure at least INFORM0 has the resume address */
>
> - __raw_writel(virt_to_phys(exynos_cpu_resume), S5P_INFORM0);
> + regmap_write(pmu_regmap, S5P_INFORM0, virt_to_phys(exynos_cpu_resume));
> }
>
> static int exynos_pm_suspend(void)
> {
> - unsigned long tmp;
> + unsigned int tmp;
>
> /* Setting Central Sequence Register for power down mode */
>
> - tmp = __raw_readl(S5P_CENTRAL_SEQ_CONFIGURATION);
> + regmap_read(pmu_regmap, S5P_CENTRAL_SEQ_CONFIGURATION, &tmp);
> tmp &= ~S5P_CENTRAL_LOWPWR_CFG;
> - __raw_writel(tmp, S5P_CENTRAL_SEQ_CONFIGURATION);
> -
> + regmap_write(pmu_regmap, S5P_CENTRAL_SEQ_CONFIGURATION, tmp);
> /* Setting SEQ_OPTION register */
>
> tmp = (S5P_USE_STANDBY_WFI0 | S5P_USE_STANDBY_WFE0);
> - __raw_writel(tmp, S5P_CENTRAL_SEQ_OPTION);
> + regmap_write(pmu_regmap, S5P_CENTRAL_SEQ_OPTION, tmp);
>
> if (!soc_is_exynos5250()) {
> /* Save Power control register */
> @@ -180,7 +184,7 @@ static int exynos_pm_suspend(void)
>
> static void exynos_pm_resume(void)
> {
> - unsigned long tmp;
> + unsigned int tmp;
>
> /*
> * If PMU failed while entering sleep mode, WFI will be
> @@ -188,12 +192,12 @@ static void exynos_pm_resume(void)
> * S5P_CENTRAL_LOWPWR_CFG bit will not be set automatically
> * in this situation.
> */
> - tmp = __raw_readl(S5P_CENTRAL_SEQ_CONFIGURATION);
> + regmap_read(pmu_regmap, S5P_CENTRAL_SEQ_CONFIGURATION, &tmp);
> if (!(tmp & S5P_CENTRAL_LOWPWR_CFG)) {
> tmp |= S5P_CENTRAL_LOWPWR_CFG;
> - __raw_writel(tmp, S5P_CENTRAL_SEQ_CONFIGURATION);
> + regmap_write(pmu_regmap, S5P_CENTRAL_SEQ_CONFIGURATION, tmp);
> /* clear the wakeup state register */
> - __raw_writel(0x0, S5P_WAKEUP_STAT);
> + regmap_write(pmu_regmap, S5P_WAKEUP_STAT, 0x0);
> /* No need to perform below restore code */
> goto early_wakeup;
> }
> @@ -213,13 +217,13 @@ static void exynos_pm_resume(void)
>
> /* For release retention */
>
> - __raw_writel((1 << 28), S5P_PAD_RET_MAUDIO_OPTION);
> - __raw_writel((1 << 28), S5P_PAD_RET_GPIO_OPTION);
> - __raw_writel((1 << 28), S5P_PAD_RET_UART_OPTION);
> - __raw_writel((1 << 28), S5P_PAD_RET_MMCA_OPTION);
> - __raw_writel((1 << 28), S5P_PAD_RET_MMCB_OPTION);
> - __raw_writel((1 << 28), S5P_PAD_RET_EBIA_OPTION);
> - __raw_writel((1 << 28), S5P_PAD_RET_EBIB_OPTION);
> + regmap_write(pmu_regmap, S5P_PAD_RET_MAUDIO_OPTION, (1 << 28));
> + regmap_write(pmu_regmap, S5P_PAD_RET_GPIO_OPTION, (1 << 28));
> + regmap_write(pmu_regmap, S5P_PAD_RET_UART_OPTION, (1 << 28));
> + regmap_write(pmu_regmap, S5P_PAD_RET_MMCA_OPTION, (1 << 28));
> + regmap_write(pmu_regmap, S5P_PAD_RET_MMCB_OPTION, (1 << 28));
> + regmap_write(pmu_regmap, S5P_PAD_RET_EBIA_OPTION, (1 << 28));
> + regmap_write(pmu_regmap, S5P_PAD_RET_EBIB_OPTION, (1 << 28));
>
> if (soc_is_exynos5250())
> s3c_pm_do_restore(exynos5_sys_save,
> @@ -233,7 +237,7 @@ static void exynos_pm_resume(void)
> early_wakeup:
>
> /* Clear SLEEP mode set in INFORM1 */
> - __raw_writel(0x0, S5P_INFORM1);
> + regmap_write(pmu_regmap, S5P_INFORM1, 0x0);
>
> return;
> }
> @@ -276,8 +280,8 @@ static int exynos_suspend_enter(suspend_state_t state)
>
> s3c_pm_restore_uarts();
>
> - S3C_PMDBG("%s: wakeup stat: %08x\n", __func__,
> - __raw_readl(S5P_WAKEUP_STAT));
> + regmap_read(pmu_regmap, S5P_WAKEUP_STAT, &ret);
> + S3C_PMDBG("%s: wakeup stat: %08x\n", __func__, ret);
>
> s3c_pm_check_restore();
>
> @@ -308,14 +312,14 @@ static const struct platform_suspend_ops exynos_suspend_ops = {
> void __init exynos_pm_init(void)
> {
> u32 tmp;
> -
> + pmu_regmap = get_exynos_pmuregmap();
> /* Platform-specific GIC callback */
> gic_arch_extn.irq_set_wake = exynos_irq_set_wake;
>
> /* All wakeup disable */
> - tmp = __raw_readl(S5P_WAKEUP_MASK);
> + regmap_read(pmu_regmap, S5P_WAKEUP_MASK, &tmp);
> tmp |= ((0xFF << 8) | (0x1F << 1));
> - __raw_writel(tmp, S5P_WAKEUP_MASK);
> + regmap_write(pmu_regmap, S5P_WAKEUP_MASK, tmp);
>
> register_syscore_ops(&exynos_pm_syscore_ops);
> suspend_set_ops(&exynos_suspend_ops);
As I said above, I don't think there is any need to use the regmap in
such low level code for registers that will not be shared.
> diff --git a/arch/arm/mach-exynos/pmu.c b/arch/arm/mach-exynos/pmu.c
> index 4c3453a..67116a5 100644
> --- a/arch/arm/mach-exynos/pmu.c
> +++ b/arch/arm/mach-exynos/pmu.c
> @@ -11,6 +11,7 @@
>
> #include <linux/io.h>
> #include <linux/kernel.h>
> +#include <linux/regmap.h>
>
> #include <plat/cpu.h>
>
> @@ -18,6 +19,7 @@
> #include "regs-pmu.h"
>
> static const struct exynos_pmu_conf *exynos_pmu_config;
> +static struct regmap *pmu_regmap;
>
> static const struct exynos_pmu_conf exynos4210_pmu_config[] = {
> /* { .reg = address, .val = { AFTR, LPA, SLEEP } */
> @@ -317,7 +319,7 @@ static const struct exynos_pmu_conf exynos5250_pmu_config[] = {
> { PMU_TABLE_END,},
> };
>
> -static void __iomem * const exynos5_list_both_cnt_feed[] = {
> +static unsigned int const exynos5_list_both_cnt_feed[] = {
> EXYNOS5_ARM_CORE0_OPTION,
> EXYNOS5_ARM_CORE1_OPTION,
> EXYNOS5_ARM_COMMON_OPTION,
> @@ -331,7 +333,7 @@ static void __iomem * const exynos5_list_both_cnt_feed[] = {
> EXYNOS5_TOP_PWR_SYSMEM_OPTION,
> };
>
> -static void __iomem * const exynos5_list_diable_wfi_wfe[] = {
> +static unsigned int const exynos5_list_diable_wfi_wfe[] = {
> EXYNOS5_ARM_CORE1_OPTION,
> EXYNOS5_FSYS_ARM_OPTION,
> EXYNOS5_ISP_ARM_OPTION,
> @@ -346,27 +348,28 @@ static void exynos5_init_pmu(void)
> * Enable both SC_FEEDBACK and SC_COUNTER
> */
> for (i = 0 ; i < ARRAY_SIZE(exynos5_list_both_cnt_feed) ; i++) {
> - tmp = __raw_readl(exynos5_list_both_cnt_feed[i]);
> + regmap_read(pmu_regmap, exynos5_list_both_cnt_feed[i], &tmp);
> tmp |= (EXYNOS5_USE_SC_FEEDBACK |
> EXYNOS5_USE_SC_COUNTER);
> - __raw_writel(tmp, exynos5_list_both_cnt_feed[i]);
> + regmap_write(pmu_regmap, exynos5_list_both_cnt_feed[i], tmp);
> }
>
> /*
> * SKIP_DEACTIVATE_ACEACP_IN_PWDN_BITFIELD Enable
> */
> - tmp = __raw_readl(EXYNOS5_ARM_COMMON_OPTION);
> + regmap_read(pmu_regmap, EXYNOS5_ARM_COMMON_OPTION, &tmp);
> tmp |= EXYNOS5_SKIP_DEACTIVATE_ACEACP_IN_PWDN;
> - __raw_writel(tmp, EXYNOS5_ARM_COMMON_OPTION);
> + regmap_write(pmu_regmap, EXYNOS5_ARM_COMMON_OPTION, tmp);
>
> /*
> * Disable WFI/WFE on XXX_OPTION
> */
> for (i = 0 ; i < ARRAY_SIZE(exynos5_list_diable_wfi_wfe) ; i++) {
> - tmp = __raw_readl(exynos5_list_diable_wfi_wfe[i]);
> + tmp = regmap_read(pmu_regmap, exynos5_list_diable_wfi_wfe[i],
> + &tmp);
> tmp &= ~(EXYNOS5_OPTION_USE_STANDBYWFE |
> EXYNOS5_OPTION_USE_STANDBYWFI);
> - __raw_writel(tmp, exynos5_list_diable_wfi_wfe[i]);
> + regmap_write(pmu_regmap, exynos5_list_diable_wfi_wfe[i], tmp);
> }
> }
>
> @@ -377,14 +380,14 @@ void exynos_sys_powerdown_conf(enum sys_powerdown mode)
> if (soc_is_exynos5250())
> exynos5_init_pmu();
>
> - for (i = 0; (exynos_pmu_config[i].reg != PMU_TABLE_END) ; i++)
> - __raw_writel(exynos_pmu_config[i].val[mode],
> - exynos_pmu_config[i].reg);
> + for (i = 0; (exynos_pmu_config[i].offset != PMU_TABLE_END) ; i++)
> + regmap_write(pmu_regmap, exynos_pmu_config[i].offset,
> + exynos_pmu_config[i].val[mode]);
>
> if (soc_is_exynos4412()) {
> - for (i = 0; exynos4412_pmu_config[i].reg != PMU_TABLE_END ; i++)
> - __raw_writel(exynos4412_pmu_config[i].val[mode],
> - exynos4412_pmu_config[i].reg);
> + for (i = 0; exynos4412_pmu_config[i].offset != PMU_TABLE_END; i++)
> + regmap_write(pmu_regmap, exynos4412_pmu_config[i].offset,
> + exynos4412_pmu_config[i].val[mode]);
> }
> }
>
> @@ -393,6 +396,7 @@ static int __init exynos_pmu_init(void)
> unsigned int value;
>
> exynos_pmu_config = exynos4210_pmu_config;
> + pmu_regmap = get_exynos_pmuregmap();
>
> if (soc_is_exynos4210()) {
> exynos_pmu_config = exynos4210_pmu_config;
> @@ -405,13 +409,13 @@ static int __init exynos_pmu_init(void)
> * When SYS_WDTRESET is set, watchdog timer reset request
> * is ignored by power management unit.
> */
> - value = __raw_readl(EXYNOS5_AUTO_WDTRESET_DISABLE);
> + regmap_read(pmu_regmap, EXYNOS5_AUTO_WDTRESET_DISABLE, &value);
> value &= ~EXYNOS5_SYS_WDTRESET;
> - __raw_writel(value, EXYNOS5_AUTO_WDTRESET_DISABLE);
> + regmap_write(pmu_regmap, EXYNOS5_AUTO_WDTRESET_DISABLE, value);
>
> - value = __raw_readl(EXYNOS5_MASK_WDTRESET_REQUEST);
> + regmap_read(pmu_regmap, EXYNOS5_MASK_WDTRESET_REQUEST, &value);
> value &= ~EXYNOS5_SYS_WDTRESET;
> - __raw_writel(value, EXYNOS5_MASK_WDTRESET_REQUEST);
> + regmap_write(pmu_regmap, EXYNOS5_MASK_WDTRESET_REQUEST, value);
>
> exynos_pmu_config = exynos5250_pmu_config;
> pr_info("EXYNOS5250 PMU Initialize\n");
Same here.
> diff --git a/arch/arm/mach-exynos/regs-pmu.h b/arch/arm/mach-exynos/regs-pmu.h
> index bfebe84..7f3bf65 100644
> --- a/arch/arm/mach-exynos/regs-pmu.h
> +++ b/arch/arm/mach-exynos/regs-pmu.h
> @@ -14,290 +14,288 @@
>
> #include <mach/map.h>
>
Is inclusion of this header still needed after getting rid of S5P_VA_PMU
below?
> -#define S5P_PMUREG(x) (S5P_VA_PMU + (x))
> -
Best regards,
Tomasz
More information about the linux-arm-kernel
mailing list