[PATCH] ARM: i.MX6: Add OF configuration support for ksz9031
Alexandre Belloni
alexandre.belloni at free-electrons.com
Tue Apr 22 09:21:17 PDT 2014
Hi,
As this is version two of your patch, you should probably use [PATCHv2].
Also, this doesn't have anything to do with i.mx6 anymore. I think youe
subject line should look like:
[PATCHv2] net: phy: micrel: Add DT configuration support for ksz9031
On 22/04/2014 at 17:49:08 +0200, Hubert Chaumette wrote :
> Adds support for ksz9031 PAD skew configuration over devicetree.
>
> Changes since v1:
> - Removed ksz9021 and ksz9031 fixup deletions from arch/arm/mach-imx/mach-imx6q.c
>
> Signed-off-by: Hubert Chaumette <hchaumette at adeneo-embedded.com>
> ---
> drivers/net/phy/micrel.c | 185 ++++++++++++++++++++++++++++++++++++++++++++++-
> 1 file changed, 184 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c
> index 5a8993b..df56b26 100644
> --- a/drivers/net/phy/micrel.c
> +++ b/drivers/net/phy/micrel.c
> @@ -242,6 +242,189 @@ static int ksz9021_config_init(struct phy_device *phydev)
> return 0;
> }
>
> +#define MII_KSZ9031RN_MMD_CTRL_REG 0x0d
> +#define MII_KSZ9031RN_MMD_REGDATA_REG 0x0e
> +#define OP_DATA 1
> +#define KSZ9031_PS_TO_REG 60
> +
> +/* Extended registers */
> +#define MII_KSZ9031RN_CONTROL_PAD_SKEW 4
> +#define MII_KSZ9031RN_RX_DATA_PAD_SKEW 5
> +#define MII_KSZ9031RN_TX_DATA_PAD_SKEW 6
> +#define MII_KSZ9031RN_CLK_PAD_SKEW 8
> +
> +static int ksz9031_extended_write(struct phy_device *phydev,
> + u8 mode, u32 dev_addr, u32 regnum, u16 val)
> +{
> + phy_write(phydev, MII_KSZ9031RN_MMD_CTRL_REG, dev_addr);
> + phy_write(phydev, MII_KSZ9031RN_MMD_REGDATA_REG, regnum);
> + phy_write(phydev, MII_KSZ9031RN_MMD_CTRL_REG, (mode << 14) | dev_addr);
> + return phy_write(phydev, MII_KSZ9031RN_MMD_REGDATA_REG, val);
> +}
> +
> +static int ksz9031_extended_read(struct phy_device *phydev,
> + u8 mode, u32 dev_addr, u32 regnum)
> +{
> + phy_write(phydev, MII_KSZ9031RN_MMD_CTRL_REG, dev_addr);
> + phy_write(phydev, MII_KSZ9031RN_MMD_REGDATA_REG, regnum);
> + phy_write(phydev, MII_KSZ9031RN_MMD_CTRL_REG, (mode << 14) | dev_addr);
> + return phy_read(phydev, MII_KSZ9031RN_MMD_REGDATA_REG);
> +}
> +
> +/* Two 5-bit fields register */
> +static int ksz9031_load_clk_skew_values(struct phy_device *phydev,
> + struct device_node *of_node,
> + char *field1, char *field2)
> +{
> + int val1 = -1;
> + int val2 = -2;
> + int newval;
> + int matches = 0;
> +
> + if (!of_property_read_u32(of_node, field1, &val1))
> + matches++;
> +
> + if (!of_property_read_u32(of_node, field2, &val2))
> + matches++;
> +
> + if (!matches)
> + return 0;
> +
> + if (matches < 2)
> + newval = ksz9031_extended_read(phydev, OP_DATA, 2,
> + MII_KSZ9031RN_CLK_PAD_SKEW);
> + else
> + newval = 0;
> +
> + if (val1 != -1)
> + newval = (newval & 0xffe0) |
> + ((val1 / KSZ9031_PS_TO_REG) & 0x1f);
> +
> + if (val2 != -2)
> + newval = (newval & 0xfc1f) |
> + (((val2 / KSZ9031_PS_TO_REG) & 0x1f) << 5);
> +
> + return ksz9031_extended_write(phydev, OP_DATA, 2,
> + MII_KSZ9031RN_CLK_PAD_SKEW, newval);
> +}
> +
> +/* Four 4-bit fields register */
> +static int ksz9031_load_data_skew_values(struct phy_device *phydev,
> + struct device_node *of_node, u16 reg,
> + char *field1, char *field2,
> + char *field3, char *field4)
> +{
> + int val1 = -1;
> + int val2 = -2;
> + int val3 = -3;
> + int val4 = -4;
> + int newval;
> + int matches = 0;
> +
> + if (!of_property_read_u32(of_node, field1, &val1))
> + matches++;
> +
> + if (!of_property_read_u32(of_node, field2, &val2))
> + matches++;
> +
> + if (!of_property_read_u32(of_node, field3, &val3))
> + matches++;
> +
> + if (!of_property_read_u32(of_node, field4, &val4))
> + matches++;
> +
> + if (!matches)
> + return 0;
> +
> + if (matches < 4)
> + newval = ksz9031_extended_read(phydev, OP_DATA, 2, reg);
> + else
> + newval = 0;
> +
> + if (val1 != -1)
> + newval = (newval & 0xfff0) |
> + (((val1 / KSZ9031_PS_TO_REG) & 0xf) << 0);
> +
> + if (val2 != -2)
> + newval = (newval & 0xff0f) |
> + (((val2 / KSZ9031_PS_TO_REG) & 0xf) << 4);
> +
> + if (val3 != -3)
> + newval = (newval & 0xf0ff) |
> + (((val3 / KSZ9031_PS_TO_REG) & 0xf) << 8);
> +
> + if (val4 != -4)
> + newval = (newval & 0x0fff) |
> + (((val4 / KSZ9031_PS_TO_REG) & 0xf) << 12);
> +
> + return ksz9031_extended_write(phydev, OP_DATA, 2, reg, newval);
> +}
> +
> +/* Two 4-bit fields register */
> +static int ksz9031_load_ctrl_skew_values(struct phy_device *phydev,
> + struct device_node *of_node,
> + char *field1, char *field2)
> +{
> + int val1 = -1;
> + int val2 = -2;
> + int newval;
> + int matches = 0;
> +
> + if (!of_property_read_u32(of_node, field1, &val1))
> + matches++;
> +
> + if (!of_property_read_u32(of_node, field2, &val2))
> + matches++;
> +
> + if (!matches)
> + return 0;
> +
> + if (matches < 2)
> + newval = ksz9031_extended_read(phydev, OP_DATA, 2,
> + MII_KSZ9031RN_CONTROL_PAD_SKEW);
> + else
> + newval = 0;
> +
> + if (val1 != -1)
> + newval = (newval & 0xfff0) |
> + (((val1 / KSZ9031_PS_TO_REG) & 0xf) << 0);
> +
> + if (val2 != -2)
> + newval = (newval & 0xff0f) |
> + (((val2 / KSZ9031_PS_TO_REG) & 0xf) << 4);
> +
> + return ksz9031_extended_write(phydev, OP_DATA, 2,
> + MII_KSZ9031RN_CONTROL_PAD_SKEW, newval);
> +}
> +
> +static int ksz9031_config_init(struct phy_device *phydev)
> +{
> + struct device *dev = &phydev->dev;
> + struct device_node *of_node = dev->of_node;
> +
> + if (!of_node && dev->parent->of_node)
> + of_node = dev->parent->of_node;
> +
> + if (of_node) {
> + ksz9031_load_clk_skew_values(phydev, of_node,
> + "rxc-skew-ps", "txc-skew-ps");
> +
> + ksz9031_load_data_skew_values(phydev, of_node,
> + MII_KSZ9031RN_RX_DATA_PAD_SKEW,
> + "rxd0-skew-ps", "rxd1-skew-ps",
> + "rxd2-skew-ps", "rxd3-skew-ps");
> +
> + ksz9031_load_data_skew_values(phydev, of_node,
> + MII_KSZ9031RN_TX_DATA_PAD_SKEW,
> + "txd0-skew-ps", "txd1-skew-ps",
> + "txd2-skew-ps", "txd3-skew-ps");
> +
> + ksz9031_load_ctrl_skew_values(phydev, of_node,
> + "txen-skew-ps", "rxdv-skew-ps");
> + }
> + return 0;
> +}
> +
> #define KSZ8873MLL_GLOBAL_CONTROL_4 0x06
> #define KSZ8873MLL_GLOBAL_CONTROL_4_DUPLEX (1 << 6)
> #define KSZ8873MLL_GLOBAL_CONTROL_4_SPEED (1 << 4)
> @@ -428,7 +611,7 @@ static struct phy_driver ksphy_driver[] = {
> .features = (PHY_GBIT_FEATURES | SUPPORTED_Pause
> | SUPPORTED_Asym_Pause),
> .flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
> - .config_init = kszphy_config_init,
> + .config_init = ksz9031_config_init,
> .config_aneg = genphy_config_aneg,
> .read_status = genphy_read_status,
> .ack_interrupt = kszphy_ack_interrupt,
> --
> 1.9.2
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
--
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
More information about the linux-arm-kernel
mailing list