[PATCH v2 2/3] ARM: dts: imx27: Place the usb phy nodes in the board dts files

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam at freescale.com>

It is not a good approach to have the USB PHY nodes inside imx27.dtsi since
the USB PHYs on mx27 are not internal to the SoC.

Place the USB PHY nodes in the board dts files instead.

Also, each board may have a different clock source for the USB PHY, so do not
hardcode it.

Signed-off-by: Fabio Estevam <fabio.estevam at freescale.com>
---
Applies on top of "[PATCH] ARM: dts: imx27-phytec-phycore-som: Move PMIC IRQ GPIO into a separate pin group"

Changes since v1:
- Use a dummy clock for USB PHY
- Put usbphy2 into the rdk dts file

 arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts  | 19 +++++++++++++++----
 arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi | 19 +++++++++++++++----
 arch/arm/boot/dts/imx27.dtsi                    | 22 ----------------------
 3 files changed, 30 insertions(+), 30 deletions(-)

diff --git a/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts b/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts
index 8b4181b..0875327 100644
--- a/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts
+++ b/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts
@@ -37,6 +37,20 @@
 			};
 		};
 	};
+
+	usbphy {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		usbphy2: usbphy at 2 {
+			compatible = "usb-nop-xceiv";
+			reg = <0>;
+			vcc-supply = <&reg_5v0>;
+			clocks = <&clks 0>;
+			clock-names = "main_clk";
+		};
+	};
 };
 
 &cspi1 {
@@ -268,14 +282,11 @@
 	dr_mode = "host";
 	phy_type = "ulpi";
 	vbus-supply = <&reg_5v0>;
+	fsl,usbphy = <&usbphy2>;
 	disable-over-current;
 	status = "okay";
 };
 
-&usbphy2 {
-	vcc-supply = <&reg_5v0>;
-};
-
 &weim {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_weim>;
diff --git a/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi b/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi
index 33c5dc2..32cc7dac9a 100644
--- a/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi
+++ b/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi
@@ -41,6 +41,20 @@
 			regulator-max-microvolt = <5000000>;
 		};
 	};
+
+	usbphy {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		usbphy0: usbphy at 0 {
+			compatible = "usb-nop-xceiv";
+			reg = <0>;
+			vcc-supply = <&sw3_reg>;
+			clocks = <&clks 0>;
+			clock-names = "main_clk";
+		};
+	};
 };
 
 &audmux {
@@ -307,14 +321,11 @@
 	pinctrl-0 = <&pinctrl_usbotg>;
 	dr_mode = "otg";
 	phy_type = "ulpi";
+	fsl,usbphy = <&usbphy0>;
 	vbus-supply = <&sw3_reg>;
 	status = "okay";
 };
 
-&usbphy0 {
-	vcc-supply = <&sw3_reg>;
-};
-
 &weim {
 	status = "okay";
 
diff --git a/arch/arm/boot/dts/imx27.dtsi b/arch/arm/boot/dts/imx27.dtsi
index 948354e..b2c103e 100644
--- a/arch/arm/boot/dts/imx27.dtsi
+++ b/arch/arm/boot/dts/imx27.dtsi
@@ -72,26 +72,6 @@
 		};
 	};
 
-	usbphy {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		usbphy0: usbphy at 0 {
-			compatible = "usb-nop-xceiv";
-			reg = <0>;
-			clocks = <&clks 75>;
-			clock-names = "main_clk";
-		};
-
-		usbphy2: usbphy at 2 {
-			compatible = "usb-nop-xceiv";
-			reg = <2>;
-			clocks = <&clks 75>;
-			clock-names = "main_clk";
-		};
-	};
-
 	soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -467,7 +447,6 @@
 				interrupts = <56>;
 				clocks = <&clks 75>;
 				fsl,usbmisc = <&usbmisc 0>;
-				fsl,usbphy = <&usbphy0>;
 				status = "disabled";
 			};
 
@@ -486,7 +465,6 @@
 				interrupts = <55>;
 				clocks = <&clks 75>;
 				fsl,usbmisc = <&usbmisc 2>;
-				fsl,usbphy = <&usbphy2>;
 				status = "disabled";
 			};
 
-- 
1.8.3.2