[PATCH v5 01/20] clk: shmobile: r8a7779: Add clocks support
Laurent Pinchart
laurent.pinchart at ideasonboard.com
Wed Apr 16 02:27:13 PDT 2014
Hi Simon,
Thank you for the patch.
On Wednesday 16 April 2014 10:57:15 Simon Horman wrote:
> The R8A7779 SoC has several clocks that are too custom to be supported in a
> generic driver. Those clocks are all fixed rate clocks with multiplier and
> divisor set according to boot mode configuration.
>
> Based on work for R-Car Gen2 SoCs by Laurent Pinchart.
>
> Cc: Laurent Pinchart <laurent.pinchart+renesas at ideasonboard.com>
> Cc: devicetree at vger.kernel.org
> Signed-off-by: Simon Horman <horms+renesas at verge.net.au>
Acked-by: Laurent Pinchart <laurent.pinchart at ideasonboard.com>
>
> ---
>
> Laurent Pinchart suggested an "renesas,rcar-gen1-cpg-clocks" compat string,
> however, I have decided against including this as I do not believe
> that it describes the hardware as to my knowledge the documentation
> does not explicitly state that the hardware is compatible between
> different R-Car Gen 1 SoCs.
>
> v5
> * Rebase
> * As suggested by Laurent Pinchart
> - Do not print an error if kzalloc() fails,
> kzalloc() will print OOM message to the kernel log in such cases
> v4
> * As suggested by Geert Uytterhoeven
> - Remove double and from bindings documentation
> - Remove unused CPG_PLL_CONFIG_INDEX and struct cpg_pll_config
> - Correct order of cpg_clk_configs entries
> * As suggested by Laurent Pinchart
> - Update copyright to include 2014
> - Remove reference to non-existent divider clocks in changelog
> - Do not map cpg->reg as it is not accessed
> - Return an error for unknown name values in r8a7779_cpg_register_clock()
> - Expose clkb in binding
> - Do not include MSPT registers in register range in binding example
> * Write (BIT(2)|BIT(1)) instead of (BIT(1)|BIT(2)) as it is less confusing
> (to me)
> v3
> * As suggested by Laurent Pinchart
> - Added external clock input
> - Use PLLA ratio set bu MD11 and MD12
> - Add _div suffixes of fields of struct cpt_clk_config
> - Register PLLA as a fixed factor clock
> - Use sizeof() instead of sizeof
> - Use num_clks instead of CPG_NUM_CLOCKS in r8a7779_cpg_clocks_init()
>
> - I kept this as r8a7779 binding rather than moving to a R-Car Gen1
> binding which could be shared with other SoCs as I do not believe that
> the SoCs is are sufficiently similar.
> ---
> .../bindings/clock/renesas,r8a7779-cpg-clocks.txt | 27 ++++
> drivers/clk/shmobile/Makefile | 1 +
> drivers/clk/shmobile/clk-r8a7779.c | 180
> +++++++++++++++++++++ include/linux/clk/shmobile.h |
> 3 +
> 4 files changed, 211 insertions(+)
> create mode 100644
> Documentation/devicetree/bindings/clock/renesas,r8a7779-cpg-clocks.txt
> create mode 100644 drivers/clk/shmobile/clk-r8a7779.c
>
> diff --git
> a/Documentation/devicetree/bindings/clock/renesas,r8a7779-cpg-clocks.txt
> b/Documentation/devicetree/bindings/clock/renesas,r8a7779-cpg-clocks.txt
> new file mode 100644
> index 0000000..ed3c8cb
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/clock/renesas,r8a7779-cpg-clocks.txt
> @@ -0,0 +1,27 @@
> +* Renesas R8A7779 Clock Pulse Generator (CPG)
> +
> +The CPG generates core clocks for the R8A7779. It includes one PLL and
> +several fixed ratio dividers
> +
> +Required Properties:
> +
> + - compatible: Must be "renesas,r8a7779-cpg-clocks"
> + - reg: Base address and length of the memory resource used by the CPG
> +
> + - clocks: Reference to the parent clock
> + - #clock-cells: Must be 1
> + - clock-output-names: The names of the clocks. Supported clocks are
> "plla", + "z", "zs", "s", "s1", "p", "b", "out".
> +
> +
> +Example
> +-------
> +
> + cpg_clocks: cpg_clocks at ffc80000 {
> + compatible = "renesas,r8a7779-cpg-clocks";
> + reg = <0 0xffc80000 0 0x30>;
> + clocks = <&extal_clk>;
> + #clock-cells = <1>;
> + clock-output-names = "plla", "z", "zs", "s", "s1", "p",
> + "b", "out";
> + };
> diff --git a/drivers/clk/shmobile/Makefile b/drivers/clk/shmobile/Makefile
> index 5404cb9..bdf342d 100644
> --- a/drivers/clk/shmobile/Makefile
> +++ b/drivers/clk/shmobile/Makefile
> @@ -1,5 +1,6 @@
> obj-$(CONFIG_ARCH_EMEV2) += clk-emev2.o
> obj-$(CONFIG_ARCH_R7S72100) += clk-rz.o
> +obj-$(CONFIG_ARCH_R8A7779) += clk-r8a7779.o
> obj-$(CONFIG_ARCH_R8A7790) += clk-rcar-gen2.o
> obj-$(CONFIG_ARCH_R8A7791) += clk-rcar-gen2.o
> obj-$(CONFIG_ARCH_SHMOBILE_MULTI) += clk-div6.o
> diff --git a/drivers/clk/shmobile/clk-r8a7779.c
> b/drivers/clk/shmobile/clk-r8a7779.c new file mode 100644
> index 0000000..652ecac
> --- /dev/null
> +++ b/drivers/clk/shmobile/clk-r8a7779.c
> @@ -0,0 +1,180 @@
> +/*
> + * r8a7779 Core CPG Clocks
> + *
> + * Copyright (C) 2013, 2014 Horms Solutions Ltd.
> + *
> + * Contact: Simon Horman <horms at verge.net.au>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; version 2 of the License.
> + */
> +
> +#include <linux/clk-provider.h>
> +#include <linux/clkdev.h>
> +#include <linux/clk/shmobile.h>
> +#include <linux/init.h>
> +#include <linux/kernel.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/spinlock.h>
> +
> +#include <dt-bindings/clock/r8a7779-clock.h>
> +
> +#define CPG_NUM_CLOCKS (R8A7779_CLK_OUT + 1)
> +
> +struct r8a7779_cpg {
> + struct clk_onecell_data data;
> + spinlock_t lock;
> + void __iomem *reg;
> +};
> +
> +/*
> ---------------------------------------------------------------------------
> -- + * CPG Clock Data
> + */
> +
> +/*
> + * MD1 = 1 MD1 = 0
> + * (PLLA = 1500) (PLLA = 1600)
> + * (MHz) (MHz)
> + *------------------------------------------------+--------------------
> + * clkz 1000 (2/3) 800 (1/2)
> + * clkzs 250 (1/6) 200 (1/8)
> + * clki 750 (1/2) 800 (1/2)
> + * clks 250 (1/6) 200 (1/8)
> + * clks1 125 (1/12) 100 (1/16)
> + * clks3 187.5 (1/8) 200 (1/8)
> + * clks4 93.7 (1/16) 100 (1/16)
> + * clkp 62.5 (1/24) 50 (1/32)
> + * clkg 62.5 (1/24) 66.6 (1/24)
> + * clkb, CLKOUT
> + * (MD2 = 0) 62.5 (1/24) 66.6 (1/24)
> + * (MD2 = 1) 41.6 (1/36) 50 (1/32)
> + */
> +
> +#define CPG_CLK_CONFIG_INDEX(md) (((md) & (BIT(2)|BIT(1))) >> 1)
> +
> +struct cpg_clk_config {
> + unsigned int z_mult;
> + unsigned int z_div;
> + unsigned int zs_and_s_div;
> + unsigned int s1_div;
> + unsigned int p_div;
> + unsigned int b_and_out_div;
> +};
> +
> +static const struct cpg_clk_config cpg_clk_configs[4] __initconst = {
> + { 1, 2, 8, 16, 32, 24 },
> + { 2, 3, 6, 12, 24, 24 },
> + { 1, 2, 8, 16, 32, 32 },
> + { 2, 3, 6, 12, 24, 36 },
> +};
> +
> +/*
> + * MD PLLA Ratio
> + * 12 11
> + *------------------------
> + * 0 0 x42
> + * 0 1 x48
> + * 1 0 x56
> + * 1 1 x64
> + */
> +
> +#define CPG_PLLA_MULT_INDEX(md) (((md) & (BIT(12)|BIT(11))) >> 11)
> +
> +static const unsigned int cpg_plla_mult[4] __initconst = { 42, 48, 56, 64
> }; +
> +/*
> ---------------------------------------------------------------------------
> -- + * Initialization
> + */
> +
> +static u32 cpg_mode __initdata;
> +
> +static struct clk * __init
> +r8a7779_cpg_register_clock(struct device_node *np, struct r8a7779_cpg *cpg,
> + const struct cpg_clk_config *config,
> + unsigned int plla_mult, const char *name)
> +{
> + const char *parent_name = "plla";
> + unsigned int mult = 1;
> + unsigned int div = 1;
> +
> + if (!strcmp(name, "plla")) {
> + parent_name = of_clk_get_parent_name(np, 0);
> + mult = plla_mult;
> + } else if (!strcmp(name, "z")) {
> + div = config->z_div;
> + mult = config->z_mult;
> + } else if (!strcmp(name, "zs") || !strcmp(name, "s")) {
> + div = config->zs_and_s_div;
> + } else if (!strcmp(name, "s1")) {
> + div = config->s1_div;
> + } else if (!strcmp(name, "p")) {
> + div = config->p_div;
> + } else if (!strcmp(name, "b") || !strcmp(name, "out")) {
> + div = config->b_and_out_div;
> + } else {
> + return ERR_PTR(-EINVAL);
> + }
> +
> + return clk_register_fixed_factor(NULL, name, parent_name, 0, mult, div);
> +}
> +
> +static void __init r8a7779_cpg_clocks_init(struct device_node *np)
> +{
> + const struct cpg_clk_config *config;
> + struct r8a7779_cpg *cpg;
> + struct clk **clks;
> + unsigned int i, plla_mult;
> + int num_clks;
> +
> + num_clks = of_property_count_strings(np, "clock-output-names");
> + if (num_clks < 0) {
> + pr_err("%s: failed to count clocks\n", __func__);
> + return;
> + }
> +
> + cpg = kzalloc(sizeof(*cpg), GFP_KERNEL);
> + clks = kzalloc(CPG_NUM_CLOCKS * sizeof(*clks), GFP_KERNEL);
> + if (cpg == NULL || clks == NULL) {
> + /* We're leaking memory on purpose, there's no point in cleaning
> + * up as the system won't boot anyway.
> + */
> + return;
> + }
> +
> + spin_lock_init(&cpg->lock);
> +
> + cpg->data.clks = clks;
> + cpg->data.clk_num = num_clks;
> +
> + config = &cpg_clk_configs[CPG_CLK_CONFIG_INDEX(cpg_mode)];
> + plla_mult = cpg_plla_mult[CPG_PLLA_MULT_INDEX(cpg_mode)];
> +
> + for (i = 0; i < num_clks; ++i) {
> + const char *name;
> + struct clk *clk;
> +
> + of_property_read_string_index(np, "clock-output-names", i,
> + &name);
> +
> + clk = r8a7779_cpg_register_clock(np, cpg, config,
> + plla_mult, name);
> + if (IS_ERR(clk))
> + pr_err("%s: failed to register %s %s clock (%ld)\n",
> + __func__, np->name, name, PTR_ERR(clk));
> + else
> + cpg->data.clks[i] = clk;
> + }
> +
> + of_clk_add_provider(np, of_clk_src_onecell_get, &cpg->data);
> +}
> +CLK_OF_DECLARE(r8a7779_cpg_clks, "renesas,r8a7779-cpg-clocks",
> + r8a7779_cpg_clocks_init);
> +
> +void __init r8a7779_clocks_init(u32 mode)
> +{
> + cpg_mode = mode;
> +
> + of_clk_init(NULL);
> +}
> diff --git a/include/linux/clk/shmobile.h b/include/linux/clk/shmobile.h
> index f9bf080..9f8a140 100644
> --- a/include/linux/clk/shmobile.h
> +++ b/include/linux/clk/shmobile.h
> @@ -1,7 +1,9 @@
> /*
> * Copyright 2013 Ideas On Board SPRL
> + * Copyright 2013, 2014 Horms Solutions Ltd.
> *
> * Contact: Laurent Pinchart <laurent.pinchart at ideasonboard.com>
> + * Contact: Simon Horman <horms at verge.net.au>
> *
> * This program is free software; you can redistribute it and/or modify
> * it under the terms of the GNU General Public License as published by
> @@ -14,6 +16,7 @@
>
> #include <linux/types.h>
>
> +void r8a7779_clocks_init(u32 mode);
> void rcar_gen2_clocks_init(u32 mode);
>
> #endif
--
Regards,
Laurent Pinchart
More information about the linux-arm-kernel
mailing list