[PATCH] ARM: tegra: define Jetson TK1 regulators
Stephen Warren
swarren at wwwdotorg.org
Mon Apr 14 15:55:20 PDT 2014
From: Stephen Warren <swarren at nvidia.com>
These are mostly identical to the Venice2 regulator definitions, since
the board designs are very similar. Differences are:
- Jetson TK1 doesn't have a built-in LCD panel, so on-board regulators
are not present for the backlight, touchscreen, or panel.
- +3.3V_RUN needs to be boot-on/always-on, since it's widely used. This
change should likely be propagated to Venice2 for completeness,
although it will have no practical effect there since various other
regulators use +3.3V_RUN as their supply and are always-on.
- +3.3V_LP0 needs to be boot-on as well as always-on. One reason
is because it's used to driver the UART level-shifter; without this, I
see a brief period of UART corruption during cold boots.I suspect this
change needs to be propagated to Venice2, and we simply haven't noticed
the need since there's no UART level-shifter on Venice2.
- A few rails have different names in the schematics.
Signed-off-by: Stephen Warren <swarren at nvidia.com>
---
arch/arm/boot/dts/tegra124-jetson-tk1.dts | 230 ++++++++++++++++++++++++++++++
1 file changed, 230 insertions(+)
diff --git a/arch/arm/boot/dts/tegra124-jetson-tk1.dts b/arch/arm/boot/dts/tegra124-jetson-tk1.dts
index dedcb0c165c5..ae5c750dc515 100644
--- a/arch/arm/boot/dts/tegra124-jetson-tk1.dts
+++ b/arch/arm/boot/dts/tegra124-jetson-tk1.dts
@@ -1426,6 +1426,155 @@
bias-high-impedance;
};
};
+
+ regulators {
+ vsup-sd2-supply = <&vdd_5v0_sys>;
+ vsup-sd3-supply = <&vdd_5v0_sys>;
+ vsup-sd4-supply = <&vdd_5v0_sys>;
+ vsup-sd5-supply = <&vdd_5v0_sys>;
+ vin-ldo0-supply = <&vdd_1v35_lp0>;
+ vin-ldo1-6-supply = <&vdd_3v3_run>;
+ vin-ldo2-5-7-supply = <&vddio_1v8>;
+ vin-ldo3-4-supply = <&vdd_3v3_sys>;
+ vin-ldo9-10-supply = <&vdd_5v0_sys>;
+ vin-ldo11-supply = <&vdd_3v3_run>;
+
+ sd0 {
+ regulator-name = "+VDD_CPU_AP";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-min-microamp = <3500000>;
+ regulator-max-microamp = <3500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ ams,external-control = <2>;
+ };
+
+ sd1 {
+ regulator-name = "+VDD_CORE";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-min-microamp = <2500000>;
+ regulator-max-microamp = <2500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ ams,external-control = <1>;
+ };
+
+ vdd_1v35_lp0: sd2 {
+ regulator-name = "+1.35V_LP0(sd2)";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ sd3 {
+ regulator-name = "+1.35V_LP0(sd3)";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ sd4 {
+ regulator-name = "+1.05V_RUN";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ };
+
+ vddio_1v8: sd5 {
+ regulator-name = "+1.8V_VDDIO";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sd6 {
+ regulator-name = "+VDD_GPU_AP";
+ regulator-min-microvolt = <650000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-min-microamp = <3500000>;
+ regulator-max-microamp = <3500000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo0 {
+ regulator-name = "+1.05V_RUN_AVDD";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-boot-on;
+ regulator-always-on;
+ ams,external-control = <1>;
+ };
+
+ ldo1 {
+ regulator-name = "+1.8V_RUN_CAM";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo2 {
+ regulator-name = "+1.2V_GEN_AVDD";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3 {
+ regulator-name = "+1.05V_LP0_VDD_RTC";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ ams,enable-tracking;
+ };
+
+ ldo4 {
+ regulator-name = "+2.8V_RUN_CAM";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo5 {
+ regulator-name = "+1.2V_RUN_CAM_FRONT";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ vddio_sdmmc3: ldo6 {
+ regulator-name = "+VDDIO_SDMMC3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo7 {
+ regulator-name = "+1.05V_RUN_CAM_REAR";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ };
+
+ ldo9 {
+ regulator-name = "+3.3V_RUN_TOUCH";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo10 {
+ regulator-name = "+2.8V_RUN_CAM_AF";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo11 {
+ regulator-name = "+1.8V_RUN_VPP_FUSE";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ };
};
};
@@ -1462,6 +1611,7 @@
cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
bus-width = <4>;
+ vmmc-supply = <&vddio_sdmmc3>;
};
/* eMMC */
@@ -1525,6 +1675,72 @@
#address-cells = <1>;
#size-cells = <0>;
+ vdd_mux: regulator at 0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "+VDD_MUX";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_5v0_sys: regulator at 1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "+5V_SYS";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vdd_mux>;
+ };
+
+ vdd_3v3_sys: regulator at 2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "+3.3V_SYS";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vdd_mux>;
+ };
+
+ vdd_3v3_run: regulator at 3 {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ regulator-name = "+3.3V_RUN";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&pmic 1 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&vdd_3v3_sys>;
+ };
+
+ vdd_3v3_hdmi: regulator at 4 {
+ compatible = "regulator-fixed";
+ reg = <4>;
+ regulator-name = "+3.3V_AVDD_HDMI_AP_GATED";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vdd_3v3_run>;
+ };
+
+ vdd_usb1_vbus: regulator at 7 {
+ compatible = "regulator-fixed";
+ reg = <7>;
+ regulator-name = "+USB0_VBUS_SW";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ gpio-open-drain;
+ vin-supply = <&vdd_5v0_sys>;
+ };
+
vdd_usb3_vbus: regulator at 8 {
compatible = "regulator-fixed";
reg = <8>;
@@ -1534,6 +1750,20 @@
gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>;
enable-active-high;
gpio-open-drain;
+ vin-supply = <&vdd_5v0_sys>;
+ };
+
+ vdd_3v3_lp0: regulator at 10 {
+ compatible = "regulator-fixed";
+ reg = <10>;
+ regulator-name = "+3.3V_LP0";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&pmic 2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&vdd_3v3_sys>;
};
};
--
1.8.1.5
More information about the linux-arm-kernel
mailing list