[PATCH 02/11] ARM: OMAP3: Fix idle mode signaling for sys_clkreq and sys_off_mode
Grazvydas Ignotas
notasas at gmail.com
Mon Apr 14 15:51:27 PDT 2014
On Fri, Apr 11, 2014 at 2:47 AM, Tony Lindgren <tony at atomide.com> wrote:
> While debugging legacy mode vs device tree booted PM regressions,
> I noticed that omap3 is not toggling sys_clkreq and sys_off_mode
> pins like it should.
>
> The sys_clkreq and sys_off_mode pins are not toggling because of
> the following issues:
>
> 1. The default polarity for the sys_off_mode pin is wrong.
> OFFMODE_POL needs to be cleared for sys_off_mode to go down when
> hitting off-idle, while CLKREQ_POL needs to be set so sys_clkreq
> goes down when hitting retention.
>
> 2. The values for voltctrl register need to be updated dynamically.
> We need to set either the retention idle bits, or off idle bits
> in the voltctrl register depending the idle mode we're targeting
> to hit.
>
> Let's fix these two issues as otherwise the system will just
> hang if any twl4030 PMIC idle scripts are loaded. The only case
> where the system does not hang is if only retention idle over I2C4
> is configured by the bootloader.
>
> Note that even without the twl4030 PMIC scripts, these fixes will
> do the proper signaling of sys_clkreq and sys_off_mode pins, so
> the fixes are needed to fix monitoring of PM states with LEDs or
> an oscilloscope.
>
> Cc: Kevin Hilman <khilman at linaro.org>
> Cc: Nishanth Menon <nm at ti.com>
> Cc: Paul Walmsley <paul at pwsan.com>
> Cc: Tero Kristo <t-kristo at ti.com>
> Signed-off-by: Tony Lindgren <tony at atomide.com>
> ---
> arch/arm/mach-omap2/pm34xx.c | 2 +
> arch/arm/mach-omap2/prm-regbits-34xx.h | 11 ++++-
> arch/arm/mach-omap2/vc.c | 75 +++++++++++++++++++++++++++++++++-
> arch/arm/mach-omap2/vc.h | 2 +
> 4 files changed, 87 insertions(+), 3 deletions(-)
>
> diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c
> index 87099bb..3119ec2 100644
> --- a/arch/arm/mach-omap2/pm34xx.c
> +++ b/arch/arm/mach-omap2/pm34xx.c
> @@ -50,6 +50,7 @@
> #include "sdrc.h"
> #include "sram.h"
> #include "control.h"
> +#include "vc.h"
>
> /* pm34xx errata defined in pm.h */
> u16 pm34xx_errata;
> @@ -282,6 +283,7 @@ void omap_sram_idle(void)
>
> /* CORE */
> if (core_next_state < PWRDM_POWER_ON) {
> + omap3_vc_set_pmic_signaling(core_next_state);
I wonder how is it going to affect latencies, adding stuff to suspend
path hurts things like NAND transfers, which consist of lots of small
blocks with an interrupt after each..
> if (core_next_state == PWRDM_POWER_OFF) {
> omap3_core_save_context();
> omap3_cm_save_context();
> diff --git a/arch/arm/mach-omap2/prm-regbits-34xx.h b/arch/arm/mach-omap2/prm-regbits-34xx.h
> index cebad56..106132d 100644
> --- a/arch/arm/mach-omap2/prm-regbits-34xx.h
> +++ b/arch/arm/mach-omap2/prm-regbits-34xx.h
> @@ -123,8 +123,15 @@
> #define OMAP3430_GLOBAL_SW_RST_SHIFT 1
> #define OMAP3430_GLOBAL_COLD_RST_SHIFT 0
> #define OMAP3430_GLOBAL_COLD_RST_MASK (1 << 0)
> -#define OMAP3430_SEL_OFF_MASK (1 << 3)
> -#define OMAP3430_AUTO_OFF_MASK (1 << 2)
> +#define OMAP3430_PRM_VOLTCTRL_SEL_VMODE (1 << 4)
> +#define OMAP3430_PRM_VOLTCTRL_SEL_OFF (1 << 3)
> +#define OMAP3430_PRM_VOLTCTRL_AUTO_OFF (1 << 2)
> +#define OMAP3430_PRM_VOLTCTRL_AUTO_RET (1 << 1)
> +#define OMAP3430_PRM_VOLTCTRL_AUTO_SLEEP (1 << 0)
> #define OMAP3430_SETUP_TIME2_MASK (0xffff << 16)
> #define OMAP3430_SETUP_TIME1_MASK (0xffff << 0)
> +#define OMAP3430_PRM_POLCTRL_OFFMODE_POL (1 << 3)
> +#define OMAP3430_PRM_POLCTRL_CLKOUT_POL (1 << 2)
> +#define OMAP3430_PRM_POLCTRL_CLKREQ_POL (1 << 1)
> +#define OMAP3430_PRM_POLCTRL_EXTVOL_POL (1 << 0)
> #endif
> diff --git a/arch/arm/mach-omap2/vc.c b/arch/arm/mach-omap2/vc.c
> index 49ac797..3d5ba5d 100644
> --- a/arch/arm/mach-omap2/vc.c
> +++ b/arch/arm/mach-omap2/vc.c
> @@ -220,6 +220,78 @@ static inline u32 omap_usec_to_32k(u32 usec)
> return DIV_ROUND_UP_ULL(32768ULL * (u64)usec, 1000000ULL);
> }
>
> +void omap3_vc_set_pmic_signaling(int core_next_state)
> +{
> + u32 voltctrl;
> +
> + voltctrl = omap2_prm_read_mod_reg(OMAP3430_GR_MOD,
> + OMAP3_PRM_VOLTCTRL_OFFSET);
> + switch (core_next_state) {
> + case PWRDM_POWER_OFF:
> + voltctrl &= ~(OMAP3430_PRM_VOLTCTRL_AUTO_RET |
> + OMAP3430_PRM_VOLTCTRL_AUTO_SLEEP);
> + voltctrl |= OMAP3430_PRM_VOLTCTRL_AUTO_OFF;
> + break;
> + case PWRDM_POWER_RET:
> + voltctrl &= ~(OMAP3430_PRM_VOLTCTRL_AUTO_OFF |
> + OMAP3430_PRM_VOLTCTRL_AUTO_SLEEP);
> + voltctrl |= OMAP3430_PRM_VOLTCTRL_AUTO_RET;
> + break;
> + default:
> + voltctrl &= ~(OMAP3430_PRM_VOLTCTRL_AUTO_OFF |
> + OMAP3430_PRM_VOLTCTRL_AUTO_RET);
> + voltctrl |= OMAP3430_PRM_VOLTCTRL_AUTO_SLEEP;
> + break;
> + }
> + omap2_prm_write_mod_reg(voltctrl, OMAP3430_GR_MOD,
> + OMAP3_PRM_VOLTCTRL_OFFSET);
Could it only write if the value changed? Caching register value would
be great too to avoid slow register accesses.
> +}
> +
> +/*
> + * Configure signal polarity for sys_clkreq and sys_off_mode pins
> + * as the default values are wrong and can cause the system to hang
> + * if any twl4030 sccripts are loaded.
s/sccripts/scripts
> + */
> +static void __init omap3_vc_init_pmic_signaling(void)
> +{
> + u32 val, old;
> +
> + val = omap2_prm_read_mod_reg(OMAP3430_GR_MOD,
> + OMAP3_PRM_POLCTRL_OFFSET);
> + old = val;
> +
> + if (old & OMAP3430_PRM_POLCTRL_CLKREQ_POL)
> + val |= OMAP3430_PRM_POLCTRL_CLKREQ_POL;
Are these 2 lines actually doing anything?
> + if (old & OMAP3430_PRM_POLCTRL_OFFMODE_POL)
> + val &= ~OMAP3430_PRM_POLCTRL_OFFMODE_POL;
Why not just clear the bit unconditionally?
> +
> + if (val != old) {
> + pr_debug("PM: fixing sys_clkreq and sys_off_mode polarity 0x%x -> 0x%x\n",
> + old, val);
> + }
> + omap2_prm_write_mod_reg(val, OMAP3430_GR_MOD,
> + OMAP3_PRM_POLCTRL_OFFSET);
Maybe move this write inside the block just above it?
--
Gražvydas
More information about the linux-arm-kernel
mailing list