[PATCH] ARM: dts: Add support for OMAP4 Variscite OM44 family
Joachim Eastwood
manabian at gmail.com
Sat Apr 12 11:41:05 PDT 2014
Add support for VAR-SOM-OM44[1] SODIMM system on module from Variscite. SoM
features a OMAP4460, 1GB RAM, Gigabit Ethernet (LAN7500) and optional WLAN/BT.
Also add support for VAR-STK-OM44 development board from Variscite. This kit
features a VAR-SOM-OM44 and the carrier board VAR-OM44CustomBoard[2]. The
VAR-STK-OM44 is the same as VAR-DVK-OM44 but without the LCD display.
omap4-var-stk-om44.dts replace the old and very limited omap4-var-som.dts.
[1] http://www.variscite.com/products/system-on-module-som/cortex-a9/var-som-om44-cpu-ti-omap-4-omap4460
[2] http://www.variscite.com/products/single-board-computers/var-om44customboard
Signed-off-by: Joachim Eastwood <manabian at gmail.com>
---
Hello,
Some features like WLAN/BT, HDMI and LCD support for VAR-DVK-OM44 is missing
from this patch set.
WLAN/BT could be fixed by adding some code to pdata-quirks.c but I'll rather
wait for proper DT bindings.
The OM44CustomBoard has a HDMI port but uses a different tranceiver than the
Panda board. So I guess it will need a new driver.
I will eventually add HDMI support and VAR-DVK-OM44 LCD support.
best regards
Joachim Eastwood
.../devicetree/bindings/arm/omap/omap.txt | 3 +
arch/arm/boot/dts/Makefile | 2 +-
arch/arm/boot/dts/omap4-var-om44customboard.dtsi | 182 +++++++++++
arch/arm/boot/dts/omap4-var-som-om44.dtsi | 341 +++++++++++++++++++++
arch/arm/boot/dts/omap4-var-som.dts | 96 ------
arch/arm/boot/dts/omap4-var-stk-om44.dts | 16 +
6 files changed, 543 insertions(+), 97 deletions(-)
create mode 100644 arch/arm/boot/dts/omap4-var-om44customboard.dtsi
create mode 100644 arch/arm/boot/dts/omap4-var-som-om44.dtsi
delete mode 100644 arch/arm/boot/dts/omap4-var-som.dts
create mode 100644 arch/arm/boot/dts/omap4-var-stk-om44.dts
diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
index 36ede19a1630..7db69ac46188 100644
--- a/Documentation/devicetree/bindings/arm/omap/omap.txt
+++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
@@ -102,6 +102,9 @@ Boards:
- OMAP4 DuoVero with Parlor : Commercial expansion board with daughter board
compatible = "gumstix,omap4-duovero-parlor", "gumstix,omap4-duovero", "ti,omap4430", "ti,omap4";
+- OMAP4 VAR-STK-OM44 : Commercial dev kit with VAR-OM44CustomBoard and VAR-SOM-OM44 w/WLAN
+ compatible = "variscite,var-stk-om44", "variscite,var-som-om44", "ti,omap4430", "ti,omap4";
+
- OMAP3 EVM : Software Development Board for OMAP35x, AM/DM37x
compatible = "ti,omap3-evm", "ti,omap3"
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 35c146f31e46..f443ade8ae3c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -273,7 +273,7 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
omap4-panda.dtb \
omap4-panda-a4.dtb \
omap4-panda-es.dtb \
- omap4-var-som.dtb \
+ omap4-var-stk-om44.dtb \
omap4-sdp.dtb \
omap4-sdp-es23plus.dtb \
omap5-uevm.dtb \
diff --git a/arch/arm/boot/dts/omap4-var-om44customboard.dtsi b/arch/arm/boot/dts/omap4-var-om44customboard.dtsi
new file mode 100644
index 000000000000..dcb94b80283c
--- /dev/null
+++ b/arch/arm/boot/dts/omap4-var-om44customboard.dtsi
@@ -0,0 +1,182 @@
+/*
+ * Copyright (C) 2014 Joachim Eastwood <manabian at gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/ {
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_led_pins>;
+
+ led0 {
+ label = "var:green:led0";
+ gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>; /* gpio 173 */
+ linux,default-trigger = "heartbeat";
+ };
+
+ led1 {
+ label = "var:green:led1";
+ gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>; /* gpio 172 */
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_key_pins>;
+
+ user-key {
+ label = "user";
+ gpios = <&gpio6 24 GPIO_ACTIVE_HIGH>; /* gpio 184 */
+ linux,code = <276>; /* BTN_EXTRA */
+ };
+ };
+};
+
+&omap4_pmx_core {
+ uart1_pins: pinmux_uart1_pins {
+ pinctrl-single,pins = <
+ 0xfc (PIN_INPUT_PULLUP | MUX_MODE1) /* mcspi1_cs2.uart1_cts */
+ 0xfe (PIN_OUTPUT | MUX_MODE1) /* mcspi1_cs3.uart1_rts */
+ 0xe6 (PIN_INPUT_PULLUP | MUX_MODE1) /* i2c2_scl.uart1_rx */
+ 0xe8 (PIN_OUTPUT | MUX_MODE1) /* i2c2_sda.uart1_tx */
+ >;
+ };
+
+ mcspi1_pins: pinmux_mcspi1_pins {
+ pinctrl-single,pins = <
+ 0xf2 (PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */
+ 0xf4 (PIN_INPUT | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */
+ 0xf6 (PIN_INPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */
+ 0xf8 (PIN_INPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */
+ >;
+ };
+
+ mcasp_pins: pinmux_mcsasp_pins {
+ pinctrl-single,pins = <
+ 0xb8 (PIN_OUTPUT | MUX_MODE2) /* mcbsp2_dr.abe_mcasp_axr */
+ >;
+ };
+
+ dss_dpi_pins: pinmux_dss_dpi_pins {
+ pinctrl-single,pins = <
+ 0x122 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data23 */
+ 0x124 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data22 */
+ 0x126 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data21 */
+ 0x128 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data20 */
+ 0x12a (PIN_OUTPUT | MUX_MODE5) /* dispc2_data19 */
+ 0x12c (PIN_OUTPUT | MUX_MODE5) /* dispc2_data18 */
+ 0x12e (PIN_OUTPUT | MUX_MODE5) /* dispc2_data15 */
+ 0x130 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data14 */
+ 0x132 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data13 */
+ 0x134 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data12 */
+ 0x136 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data11 */
+ 0x174 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data10 */
+ 0x176 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data9 */
+ 0x178 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data16 */
+ 0x17a (PIN_OUTPUT | MUX_MODE5) /* dispc2_data17 */
+ 0x17c (PIN_OUTPUT | MUX_MODE5) /* dispc2_hsync */
+ 0x17e (PIN_OUTPUT | MUX_MODE5) /* dispc2_pclk */
+ 0x180 (PIN_OUTPUT | MUX_MODE5) /* dispc2_vsync */
+ 0x182 (PIN_OUTPUT | MUX_MODE5) /* dispc2_de */
+ 0x184 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data8 */
+ 0x186 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data7 */
+ 0x188 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data6 */
+ 0x18a (PIN_OUTPUT | MUX_MODE5) /* dispc2_data5 */
+ 0x18c (PIN_OUTPUT | MUX_MODE5) /* dispc2_data4 */
+ 0x18e (PIN_OUTPUT | MUX_MODE5) /* dispc2_data3 */
+ 0x190 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data2 */
+ 0x192 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data1 */
+ 0x194 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data0 */
+ >;
+ };
+
+ dss_hdmi_pins: pinmux_dss_hdmi_pins {
+ pinctrl-single,pins = <
+ 0x58 (PIN_INPUT_PULLUP | MUX_MODE3) /* hdmi_hpd.gpio_63 */
+ 0x5a (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */
+ 0x5c (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_scl.hdmi_scl */
+ 0x5e (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_sda.hdmi_sda */
+ >;
+ };
+
+ i2c4_pins: pinmux_i2c4_pins {
+ pinctrl-single,pins = <
+ 0xee (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */
+ 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */
+ >;
+ };
+
+ mmc5_pins: pinmux_mmc5_pins {
+ pinctrl-single,pins = <
+ 0x0b6 (PIN_INPUT | MUX_MODE3) /* abe_mcbsp2_clkx.gpio_110 */
+ 0x108 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_clk.sdmmc5_clk */
+ 0x10a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_cmd.sdmmc5_cmd */
+ 0x10c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat0.sdmmc5_dat0 */
+ 0x10e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat1.sdmmc5_dat1 */
+ 0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat2.sdmmc5_dat2 */
+ 0x112 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat3.sdmmc5_dat3 */
+ >;
+ };
+
+ gpio_led_pins: pinmux_gpio_led_pins {
+ pinctrl-single,pins = <
+ 0x13e (PIN_OUTPUT | MUX_MODE3) /* kpd_col4.gpio_172 */
+ 0x140 (PIN_OUTPUT | MUX_MODE3) /* kpd_col5.gpio_173 */
+ >;
+ };
+
+ gpio_key_pins: pinmux_gpio_key_pins {
+ pinctrl-single,pins = <
+ 0x162 (PIN_INPUT | MUX_MODE3) /* sys_boot0.gpio_184 */
+ >;
+ };
+
+ ks8851_irq_pins: pinmux_ks8851_irq_pins {
+ pinctrl-single,pins = <
+ 0x13c (PIN_INPUT_PULLUP | MUX_MODE3) /* kpd_col3.gpio_171 */
+ >;
+ };
+};
+
+&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_pins>;
+ clock-frequency = <400000>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "okay";
+};
+
+&mcspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcspi1_pins>;
+ status = "okay";
+
+ eth at 0 {
+ compatible = "ks8851";
+ pinctrl-names = "default";
+ pinctrl-0 = <&ks8851_irq_pins>;
+ spi-max-frequency = <24000000>;
+ reg = <0>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>; /* gpio 171 */
+ };
+};
+
+&mmc5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc5_pins>;
+ vmmc-supply = <&vbat>;
+ bus-width = <4>;
+ cd-gpios = <&gpio4 14 GPIO_ACTIVE_HIGH>; /* gpio 110 */
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/omap4-var-som-om44.dtsi b/arch/arm/boot/dts/omap4-var-som-om44.dtsi
new file mode 100644
index 000000000000..247922103888
--- /dev/null
+++ b/arch/arm/boot/dts/omap4-var-som-om44.dtsi
@@ -0,0 +1,341 @@
+/*
+ * Copyright (C) 2014 Joachim Eastwood <manabian at gmail.com>
+ * Copyright (C) 2012 Variscite Ltd. - http://www.variscite.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include "omap4460.dtsi"
+
+/ {
+ model = "Variscite VAR-SOM-OM44";
+ compatible = "variscite,var-som-om44", "ti,omap4430", "ti,omap4";
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x40000000>; /* 1 GB */
+ };
+
+ sound: sound {
+ compatible = "ti,abe-twl6040";
+ ti,model = "VAR-SOM-OM44";
+
+ ti,mclk-freq = <38400000>;
+ ti,mcpdm = <&mcpdm>;
+ ti,twl6040 = <&twl6040>;
+
+ /* Audio routing */
+ ti,audio-routing =
+ "Headset Stereophone", "HSOL",
+ "Headset Stereophone", "HSOR",
+ "AFML", "Line In",
+ "AFMR", "Line In";
+ };
+
+ /* HS USB Host PHY on PORT 1 */
+ hsusb1_phy: hsusb1_phy {
+ compatible = "usb-nop-xceiv";
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &hsusbb1_phy_clk_pins
+ &hsusbb1_phy_rst_pins
+ >;
+
+ reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>; /* gpio 177 */
+ vcc-supply = <&vbat>;
+
+ clocks = <&auxclk3_ck>;
+ clock-names = "main_clk";
+ clock-frequency = <19200000>;
+ };
+
+ vbat: fixedregulator-vbat {
+ compatible = "regulator-fixed";
+ regulator-name = "VBAT";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+};
+
+&omap4_pmx_core {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &hsusbb1_pins
+ >;
+
+ twl6040_pins: pinmux_twl6040_pins {
+ pinctrl-single,pins = <
+ 0x15c (PIN_OUTPUT | MUX_MODE3) /* fref_clk2_out.gpio_182 */
+ 0x160 (PIN_INPUT | MUX_MODE0) /* sys_nirq2.sys_nirq2 */
+ >;
+ };
+
+ mcpdm_pins: pinmux_mcpdm_pins {
+ pinctrl-single,pins = <
+ 0xc6 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_ul_data.abe_pdm_ul_data */
+ 0xc8 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_dl_data.abe_pdm_dl_data */
+ 0xca (PIN_INPUT_PULLUP | MUX_MODE0) /* abe_pdm_frame.abe_pdm_frame */
+ 0xcc (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_lb_clk.abe_pdm_lb_clk */
+ 0xce (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */
+ >;
+ };
+
+ tsc2004_pins: pinmux_tsc2004_pins {
+ pinctrl-single,pins = <
+ 0x50 (PIN_INPUT | MUX_MODE3) /* gpmc_ncs4.gpio_101 (irq) */
+ 0x52 (PIN_OUTPUT | MUX_MODE3) /* gpmc_ncs5.gpio_102 (rst) */
+ >;
+ };
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_cts_rctx.uart3_cts_rctx */
+ 0x102 (PIN_OUTPUT | MUX_MODE0) /* uart3_rts_sd.uart3_rts_sd */
+ 0x104 (PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
+ 0x106 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
+ >;
+ };
+
+ hsusbb1_pins: pinmux_hsusbb1_pins {
+ pinctrl-single,pins = <
+ 0x82 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_clk.usbb1_ulpiphy_clk */
+ 0x84 (PIN_OUTPUT | MUX_MODE4) /* usbb1_ulpitll_stp.usbb1_ulpiphy_stp */
+ 0x86 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dir.usbb1_ulpiphy_dir */
+ 0x88 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_nxt.usbb1_ulpiphy_nxt */
+ 0x8a (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat0.usbb1_ulpiphy_dat0 */
+ 0x8c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat1.usbb1_ulpiphy_dat1 */
+ 0x8e (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat2.usbb1_ulpiphy_dat2 */
+ 0x90 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat3.usbb1_ulpiphy_dat3 */
+ 0x92 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat4.usbb1_ulpiphy_dat4 */
+ 0x94 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat5.usbb1_ulpiphy_dat5 */
+ 0x96 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat6.usbb1_ulpiphy_dat6 */
+ 0x98 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat7.usbb1_ulpiphy_dat7 */
+ >;
+ };
+
+ hsusbb1_phy_rst_pins: pinmux_hsusbb1_phy_rst_pins {
+ pinctrl-single,pins = <
+ 0x14c (PIN_OUTPUT | MUX_MODE3) /* kpd_row2.gpio_177 */
+ >;
+ };
+
+ i2c1_pins: pinmux_i2c1_pins {
+ pinctrl-single,pins = <
+ 0xe2 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
+ 0xe4 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
+ >;
+ };
+
+ i2c3_pins: pinmux_i2c3_pins {
+ pinctrl-single,pins = <
+ 0xea (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */
+ 0xec (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */
+ >;
+ };
+
+ mmc1_pins: pinmux_mmc1_pins {
+ pinctrl-single,pins = <
+ 0xa2 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */
+ 0xa4 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */
+ 0xa6 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
+ 0xa8 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
+ 0xaa (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
+ 0xac (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
+ >;
+ };
+};
+
+&omap4_pmx_wkup {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &hsusbb1_hub_rst_pins
+ &lan7500_rst_pins
+ >;
+
+ hsusbb1_phy_clk_pins: pinmux_hsusbb1_phy_clk_pins {
+ pinctrl-single,pins = <
+ 0x18 (PIN_OUTPUT | MUX_MODE0) /* fref_clk3_out */
+ >;
+ };
+
+ hsusbb1_hub_rst_pins: pinmux_hsusbb1_hub_rst_pins {
+ pinctrl-single,pins = <
+ 0x2 (PIN_OUTPUT | MUX_MODE3) /* gpio_wk1 */
+ >;
+ };
+
+ lan7500_rst_pins: pinmux_lan7500_rst_pins {
+ pinctrl-single,pins = <
+ 0x0 (PIN_OUTPUT | MUX_MODE3) /* gpio_wk0 */
+ >;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+
+ clock-frequency = <400000>;
+
+ twl: twl at 48 {
+ reg = <0x48>;
+ /* SPI = 0, IRQ# = 7, 4 = active high level-sensitive */
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */
+ interrupt-parent = <&gic>;
+ };
+
+ twl6040: twl at 4b {
+ compatible = "ti,twl6040";
+ reg = <0x4b>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&twl6040_pins>;
+
+ /* SPI = 0, IRQ# = 119, 4 = active high level-sensitive */
+ interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */
+ interrupt-parent = <&gic>;
+ ti,audpwron-gpio = <&gpio6 22 0>; /* gpio 182 */
+
+ vio-supply = <&v1v8>;
+ v2v1-supply = <&v2v1>;
+ enable-active-high;
+ };
+};
+
+#include "twl6030.dtsi"
+#include "twl6030_omap4.dtsi"
+
+&vusim {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+};
+
+&i2c2 {
+ status = "disabled";
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pins>;
+ status = "okay";
+
+ clock-frequency = <400000>;
+
+ tsc2004 at 48 {
+ compatible = "ti,tsc2004";
+ pinctrl-names = "default";
+ pinctrl-0 = <&tsc2004_pins>;
+ reg = <0x48>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <5 IRQ_TYPE_LEVEL_LOW>; /* gpio 101 */
+ };
+
+ tmp105 at 49 {
+ compatible = "ti,tmp105";
+ reg = <0x49>;
+ };
+
+ eeprom at 50 {
+ compatible = "24c32";
+ reg = <0x50>;
+ };
+};
+
+&i2c4 {
+ status = "disabled";
+};
+
+&mcpdm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcpdm_pins>;
+ status = "okay";
+};
+
+&gpmc {
+ status = "disabled";
+};
+
+&mcspi1 {
+ status = "disabled";
+};
+
+&mcspi2 {
+ status = "disabled";
+};
+
+&mcspi3 {
+ status = "disabled";
+};
+
+&mcspi4 {
+ status = "disabled";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ vmmc-supply = <&vmmc>;
+ bus-width = <4>;
+ ti,non-removable;
+ status = "okay";
+};
+
+&mmc2 {
+ status = "disabled";
+};
+
+&mmc3 {
+ status = "disabled";
+};
+
+&mmc4 {
+ status = "disabled";
+};
+
+&mmc5 {
+ status = "disabled";
+};
+
+&uart1 {
+ status = "disabled";
+};
+
+&uart2 {
+ status = "disabled";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+ status = "okay";
+};
+
+&uart4 {
+ status = "disabled";
+};
+
+&keypad {
+ status = "disabled";
+};
+
+&twl_usb_comparator {
+ usb-supply = <&vusb>;
+};
+
+&usb_otg_hs {
+ interface-type = <1>;
+ mode = <3>;
+ power = <50>;
+};
+
+&usbhshost {
+ port1-mode = "ehci-phy";
+};
+
+&usbhsehci {
+ phys = <&hsusb1_phy>;
+};
diff --git a/arch/arm/boot/dts/omap4-var-som.dts b/arch/arm/boot/dts/omap4-var-som.dts
deleted file mode 100644
index b41269e871dd..000000000000
--- a/arch/arm/boot/dts/omap4-var-som.dts
+++ /dev/null
@@ -1,96 +0,0 @@
-/*
- * Copyright (C) 2012 Variscite Ltd. - http://www.variscite.com
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-/dts-v1/;
-
-#include "omap443x.dtsi"
-
-/ {
- model = "Variscite OMAP4 SOM";
- compatible = "var,omap4-var_som", "ti,omap4430", "ti,omap4";
-
- memory {
- device_type = "memory";
- reg = <0x80000000 0x40000000>; /* 1 GB */
- };
-
- vdd_eth: fixedregulator at 0 {
- compatible = "regulator-fixed";
- regulator-name = "VDD_ETH";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- enable-active-high;
- regulator-boot-on;
- };
-};
-
-&i2c1 {
- clock-frequency = <400000>;
-
- twl: twl at 48 {
- reg = <0x48>;
- /* SPI = 0, IRQ# = 7, 4 = active high level-sensitive */
- interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */
- interrupt-parent = <&gic>;
- };
-};
-
-#include "twl6030.dtsi"
-
-&i2c2 {
- clock-frequency = <400000>;
-};
-
-&i2c3 {
- clock-frequency = <400000>;
-
- /*
- * Temperature Sensor
- * http://www.ti.com/lit/ds/symlink/tmp105.pdf
- */
- tmp105 at 49 {
- compatible = "ti,tmp105";
- reg = <0x49>;
- };
-};
-
-&i2c4 {
- clock-frequency = <400000>;
-};
-
-&mcspi1 {
- eth at 0 {
- compatible = "ks8851";
- spi-max-frequency = <24000000>;
- reg = <0>;
- interrupt-parent = <&gpio6>;
- interrupts = <11 IRQ_TYPE_LEVEL_LOW>; /* gpio line 171 */
- vdd-supply = <&vdd_eth>;
- };
-};
-
-&mmc1 {
- vmmc-supply = <&vmmc>;
- ti,bus-width = <8>;
- ti,non-removable;
-};
-
-&mmc2 {
- status = "disabled";
-};
-
-&mmc3 {
- status = "disabled";
-};
-
-&mmc4 {
- status = "disabled";
-};
-
-&mmc5 {
- ti,bus-width = <4>;
-};
diff --git a/arch/arm/boot/dts/omap4-var-stk-om44.dts b/arch/arm/boot/dts/omap4-var-stk-om44.dts
new file mode 100644
index 000000000000..35e2364374f7
--- /dev/null
+++ b/arch/arm/boot/dts/omap4-var-stk-om44.dts
@@ -0,0 +1,16 @@
+/*
+ * Copyright (C) 2014 Joachim Eastwood <manabian at gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "omap4-var-som-om44.dtsi"
+#include "omap4-var-om44customboard.dtsi"
+
+/ {
+ model = "Variscite VAR-STK-OM44";
+ compatible = "variscite,var-stk-om44", "variscite,var-som-om44", "ti,omap4430", "ti,omap4";
+};
--
1.8.0
More information about the linux-arm-kernel
mailing list