[PATCH] pwm: mxs: set pwm_chip can_sleep flag

[Stefan Wahren]

Hi Shawn,

Am 08.04.2014 13:29, schrieb Shawn Guo:
> The .config() calls clk_get_rate() which might sleep, so we need to set
> pwm_chip can_sleep flag.  Otherwise, we see the following warning when
> using pwm driven heartbeat led.
>
> WARNING: CPU: 0 PID: 0 at kernel/locking/mutex.c:856 mutex_trylock+0x184/0x1a4()
> DEBUG_LOCKS_WARN_ON(in_interrupt())
> Modules linked in:
> CPU: 0 PID: 0 Comm: swapper Not tainted 3.14.0-rc5 #18
> [<c0015420>] (unwind_backtrace) from [<c0012cb0>] (show_stack+0x10/0x14)
> [<c0012cb0>] (show_stack) from [<c001daf8>] (warn_slowpath_common+0x6c/0x8c)
> [<c001daf8>] (warn_slowpath_common) from [<c001dbac>] (warn_slowpath_fmt+0x30/0x40)
> [<c001dbac>] (warn_slowpath_fmt) from [<c045df74>] (mutex_trylock+0x184/0x1a4)
> [<c045df74>] (mutex_trylock) from [<c0360950>] (clk_prepare_lock+0xc/0xec)
> [<c0360950>] (clk_prepare_lock) from [<c0362020>] (clk_get_rate+0xc/0x68)
> [<c0362020>] (clk_get_rate) from [<c028d07c>] (mxs_pwm_config+0x20/0x198)
> [<c028d07c>] (mxs_pwm_config) from [<c028bde8>] (pwm_config+0x60/0x70)
> [<c028bde8>] (pwm_config) from [<c034b61c>] (__led_pwm_set+0x1c/0x3c)
> [<c034b61c>] (__led_pwm_set) from [<c034bc3c>] (led_heartbeat_function+0x70/0x110)
> [<c034bc3c>] (led_heartbeat_function) from [<c00292f0>] (call_timer_fn+0x7c/0x164)
> [<c00292f0>] (call_timer_fn) from [<c00295c8>] (run_timer_softirq+0x1f0/0x260)
> [<c00295c8>] (run_timer_softirq) from [<c002255c>] (__do_softirq+0xc4/0x2f0)
> [<c002255c>] (__do_softirq) from [<c0022890>] (irq_exit+0xa4/0x10c)
> [<c0022890>] (irq_exit) from [<c0010240>] (handle_IRQ+0x34/0x84)
> [<c0010240>] (handle_IRQ) from [<c0013524>] (__irq_svc+0x44/0x54)
> [<c0013524>] (__irq_svc) from [<c00107f8>] (arch_cpu_idle+0x40/0x48)
> [<c00107f8>] (arch_cpu_idle) from [<c005deb8>] (cpu_startup_entry+0x70/0x198)
> [<c005deb8>] (cpu_startup_entry) from [<c060aac8>] (start_kernel+0x2a8/0x2f8)
>
> Reported-by: Stefan Wahren <stefan.wahren at i2se.com>
> Signed-off-by: Shawn Guo <shawn.guo at freescale.com>
> ---
>  drivers/pwm/pwm-mxs.c | 1 +
>  1 file changed, 1 insertion(+)
>
> diff --git a/drivers/pwm/pwm-mxs.c b/drivers/pwm/pwm-mxs.c
> index 9475bc7..4f1bb4e 100644
> --- a/drivers/pwm/pwm-mxs.c
> +++ b/drivers/pwm/pwm-mxs.c
> @@ -147,6 +147,7 @@ static int mxs_pwm_probe(struct platform_device *pdev)
>  	mxs->chip.dev = &pdev->dev;
>  	mxs->chip.ops = &mxs_pwm_ops;
>  	mxs->chip.base = -1;
> +	mxs->chip.can_sleep = true;
>  	ret = of_property_read_u32(np, "fsl,pwm-number", &mxs->chip.npwm);
>  	if (ret < 0) {
>  		dev_err(&pdev->dev, "failed to get pwm number: %d\n", ret);

thanks for the patch. I've tested it with our i.MX28 board and the
warning above never came. So it works.
Unfortunately the led still don't behave as expected. If i set the led
trigger to heartbeat the led goes on and stays in this state.

May be this has something to do with the following discussion

http://comments.gmane.org/gmane.linux.leds/208

Kind regards
Stefan Wahren