[PATCH] clk: qcom: Add support for IPQ8064's global clock controller (GCC)

[Stephen Boyd]

On 04/04/14 09:30, Kumar Gala wrote:
> Add a driver for the global clock controller found on IPQ8064 based
> platforms. This should allow most non-multimedia device drivers to probe
> and control their clocks.
>
> This is currently missing clocks for SATA, USB, audio and networking
> devices.
>

There shouldn't be any audio clocks in GCC.

> diff --git a/Documentation/devicetree/bindings/clock/qcom,gcc.txt b/Documentation/devicetree/bindings/clock/qcom,gcc.txt
> index 767401f..74974d6 100644
> --- a/Documentation/devicetree/bindings/clock/qcom,gcc.txt
> +++ b/Documentation/devicetree/bindings/clock/qcom,gcc.txt
> @@ -4,6 +4,7 @@ Qualcomm Global Clock & Reset Controller Binding
>  Required properties :
>  - compatible : shall contain only one of the following:
>  
> +			"qcom,gcc-ipq8064"
>  			"qcom,gcc-msm8660"
>  			"qcom,gcc-msm8960"
>  			"qcom,gcc-msm8974"
> diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig
> index 995bcfa..5d81f7d 100644
> --- a/drivers/clk/qcom/Kconfig
> +++ b/drivers/clk/qcom/Kconfig
> @@ -4,6 +4,14 @@ config COMMON_CLK_QCOM
>  	select REGMAP_MMIO
>  	select RESET_CONTROLLER
>  
> +config MSM_GCC_806X

It would be better to say IPQ_GCC_806X here instead of MSM.

> +	tristate "IPQ806x Global Clock Controller"
> +	depends on COMMON_CLK_QCOM
> +	help
> +	  Support for the global clock controller on ipq806x devices.
> +	  Say Y if you want to use peripheral devices such as UART, SPI,
> +	  i2c, USB, SD/eMMC, etc.
> +
>
> diff --git a/drivers/clk/qcom/gcc-ipq806x.c b/drivers/clk/qcom/gcc-ipq806x.c
> new file mode 100644
> index 0000000..cc5b6c8
> --- /dev/null
> +++ b/drivers/clk/qcom/gcc-ipq806x.c
[...]
> +static int gcc_ipq806x_probe(struct platform_device *pdev)
> +{
> +	struct clk *clk;
> +	struct device *dev = &pdev->dev;
> +
> +	/* Temporary until RPM clocks supported */
> +	clk = clk_register_fixed_rate(dev, "cxo", NULL, CLK_IS_ROOT, 19200000);
> +	if (IS_ERR(clk))
> +		return PTR_ERR(clk);
> +
> +	clk = clk_register_fixed_rate(dev, "pxo", NULL, CLK_IS_ROOT, 27000000);

I thought PXO was 25MHz. Is there even a CXO present? It may just be PXO.

> diff --git a/include/dt-bindings/clock/qcom,gcc-ipq806x.h b/include/dt-bindings/clock/qcom,gcc-ipq806x.h
> new file mode 100644
> index 0000000..50a640e
> --- /dev/null
> +++ b/include/dt-bindings/clock/qcom,gcc-ipq806x.h

One thing I've been considering is moving the reset defines into the
same dt-binding include as the clocks. That way we cut down on the
number of files that are all related to the same thing. What do you think?

-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation