[PATCH] ARM: imx: Remove mx51_babbage board file
Fabio Estevam
festevam at gmail.com
Fri Apr 4 08:12:59 PDT 2014
From: Fabio Estevam <fabio.estevam at freescale.com>
The device tree version for the babbage board (imx51-babbage.dtb) has a more
complete support than the board file version, so remove the board file source
code.
Signed-off-by: Fabio Estevam <fabio.estevam at freescale.com>
---
Hi Eric,
Do you think we could remove CPUIMX51SD board file well?
If so, then this would allow us to make imx51 to be device tree only (like
mx53 and mx6).
arch/arm/mach-imx/Kconfig | 15 --
arch/arm/mach-imx/Makefile | 1 -
arch/arm/mach-imx/mach-mx51_babbage.c | 428 ----------------------------------
3 files changed, 444 deletions(-)
delete mode 100644 arch/arm/mach-imx/mach-mx51_babbage.c
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index 5740296d..d56eb1a 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -711,21 +711,6 @@ config MACH_IMX51_DT
Include support for Freescale i.MX51 based platforms
using the device tree for discovery
-config MACH_MX51_BABBAGE
- bool "Support MX51 BABBAGE platforms"
- select IMX_HAVE_PLATFORM_FSL_USB2_UDC
- select IMX_HAVE_PLATFORM_IMX2_WDT
- select IMX_HAVE_PLATFORM_IMX_I2C
- select IMX_HAVE_PLATFORM_IMX_UART
- select IMX_HAVE_PLATFORM_MXC_EHCI
- select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
- select IMX_HAVE_PLATFORM_SPI_IMX
- select SOC_IMX51
- help
- Include support for MX51 Babbage platform, also known as MX51EVK in
- u-boot. This includes specific configurations for the board and its
- peripherals.
-
config MACH_EUKREA_CPUIMX51SD
bool "Support Eukrea CPUIMX51SD module"
select IMX_HAVE_PLATFORM_FSL_USB2_UDC
diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile
index f4ed830..8dd377b 100644
--- a/arch/arm/mach-imx/Makefile
+++ b/arch/arm/mach-imx/Makefile
@@ -109,7 +109,6 @@ endif
obj-$(CONFIG_SOC_IMX6) += pm-imx6.o
# i.MX5 based machines
-obj-$(CONFIG_MACH_MX51_BABBAGE) += mach-mx51_babbage.o
obj-$(CONFIG_MACH_EUKREA_CPUIMX51SD) += mach-cpuimx51sd.o
obj-$(CONFIG_MACH_EUKREA_MBIMXSD51_BASEBOARD) += eukrea_mbimxsd51-baseboard.o
diff --git a/arch/arm/mach-imx/mach-mx51_babbage.c b/arch/arm/mach-imx/mach-mx51_babbage.c
deleted file mode 100644
index f3d264a..0000000
--- a/arch/arm/mach-imx/mach-mx51_babbage.c
+++ /dev/null
@@ -1,428 +0,0 @@
-/*
- * Copyright 2009-2010 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright (C) 2009-2010 Amit Kucheria <amit.kucheria at canonical.com>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
-
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/i2c.h>
-#include <linux/gpio.h>
-#include <linux/delay.h>
-#include <linux/io.h>
-#include <linux/input.h>
-#include <linux/spi/flash.h>
-#include <linux/spi/spi.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-
-#include "common.h"
-#include "devices-imx51.h"
-#include "hardware.h"
-#include "iomux-mx51.h"
-
-#define BABBAGE_USB_HUB_RESET IMX_GPIO_NR(1, 7)
-#define BABBAGE_USBH1_STP IMX_GPIO_NR(1, 27)
-#define BABBAGE_USB_PHY_RESET IMX_GPIO_NR(2, 5)
-#define BABBAGE_FEC_PHY_RESET IMX_GPIO_NR(2, 14)
-#define BABBAGE_POWER_KEY IMX_GPIO_NR(2, 21)
-#define BABBAGE_ECSPI1_CS0 IMX_GPIO_NR(4, 24)
-#define BABBAGE_ECSPI1_CS1 IMX_GPIO_NR(4, 25)
-#define BABBAGE_SD2_CD IMX_GPIO_NR(1, 6)
-#define BABBAGE_SD2_WP IMX_GPIO_NR(1, 5)
-
-/* USB_CTRL_1 */
-#define MX51_USB_CTRL_1_OFFSET 0x10
-#define MX51_USB_CTRL_UH1_EXT_CLK_EN (1 << 25)
-
-#define MX51_USB_PLLDIV_12_MHZ 0x00
-#define MX51_USB_PLL_DIV_19_2_MHZ 0x01
-#define MX51_USB_PLL_DIV_24_MHZ 0x02
-
-static struct gpio_keys_button babbage_buttons[] = {
- {
- .gpio = BABBAGE_POWER_KEY,
- .code = BTN_0,
- .desc = "PWR",
- .active_low = 1,
- .wakeup = 1,
- },
-};
-
-static const struct gpio_keys_platform_data imx_button_data __initconst = {
- .buttons = babbage_buttons,
- .nbuttons = ARRAY_SIZE(babbage_buttons),
-};
-
-static iomux_v3_cfg_t mx51babbage_pads[] = {
- /* UART1 */
- MX51_PAD_UART1_RXD__UART1_RXD,
- MX51_PAD_UART1_TXD__UART1_TXD,
- MX51_PAD_UART1_RTS__UART1_RTS,
- MX51_PAD_UART1_CTS__UART1_CTS,
-
- /* UART2 */
- MX51_PAD_UART2_RXD__UART2_RXD,
- MX51_PAD_UART2_TXD__UART2_TXD,
-
- /* UART3 */
- MX51_PAD_EIM_D25__UART3_RXD,
- MX51_PAD_EIM_D26__UART3_TXD,
- MX51_PAD_EIM_D27__UART3_RTS,
- MX51_PAD_EIM_D24__UART3_CTS,
-
- /* I2C1 */
- MX51_PAD_EIM_D16__I2C1_SDA,
- MX51_PAD_EIM_D19__I2C1_SCL,
-
- /* I2C2 */
- MX51_PAD_KEY_COL4__I2C2_SCL,
- MX51_PAD_KEY_COL5__I2C2_SDA,
-
- /* HSI2C */
- MX51_PAD_I2C1_CLK__I2C1_CLK,
- MX51_PAD_I2C1_DAT__I2C1_DAT,
-
- /* USB HOST1 */
- MX51_PAD_USBH1_CLK__USBH1_CLK,
- MX51_PAD_USBH1_DIR__USBH1_DIR,
- MX51_PAD_USBH1_NXT__USBH1_NXT,
- MX51_PAD_USBH1_DATA0__USBH1_DATA0,
- MX51_PAD_USBH1_DATA1__USBH1_DATA1,
- MX51_PAD_USBH1_DATA2__USBH1_DATA2,
- MX51_PAD_USBH1_DATA3__USBH1_DATA3,
- MX51_PAD_USBH1_DATA4__USBH1_DATA4,
- MX51_PAD_USBH1_DATA5__USBH1_DATA5,
- MX51_PAD_USBH1_DATA6__USBH1_DATA6,
- MX51_PAD_USBH1_DATA7__USBH1_DATA7,
-
- /* USB HUB reset line*/
- MX51_PAD_GPIO1_7__GPIO1_7,
-
- /* USB PHY reset line */
- MX51_PAD_EIM_D21__GPIO2_5,
-
- /* FEC */
- MX51_PAD_EIM_EB2__FEC_MDIO,
- MX51_PAD_EIM_EB3__FEC_RDATA1,
- MX51_PAD_EIM_CS2__FEC_RDATA2,
- MX51_PAD_EIM_CS3__FEC_RDATA3,
- MX51_PAD_EIM_CS4__FEC_RX_ER,
- MX51_PAD_EIM_CS5__FEC_CRS,
- MX51_PAD_NANDF_RB2__FEC_COL,
- MX51_PAD_NANDF_RB3__FEC_RX_CLK,
- MX51_PAD_NANDF_D9__FEC_RDATA0,
- MX51_PAD_NANDF_D8__FEC_TDATA0,
- MX51_PAD_NANDF_CS2__FEC_TX_ER,
- MX51_PAD_NANDF_CS3__FEC_MDC,
- MX51_PAD_NANDF_CS4__FEC_TDATA1,
- MX51_PAD_NANDF_CS5__FEC_TDATA2,
- MX51_PAD_NANDF_CS6__FEC_TDATA3,
- MX51_PAD_NANDF_CS7__FEC_TX_EN,
- MX51_PAD_NANDF_RDY_INT__FEC_TX_CLK,
-
- /* FEC PHY reset line */
- MX51_PAD_EIM_A20__GPIO2_14,
-
- /* SD 1 */
- MX51_PAD_SD1_CMD__SD1_CMD,
- MX51_PAD_SD1_CLK__SD1_CLK,
- MX51_PAD_SD1_DATA0__SD1_DATA0,
- MX51_PAD_SD1_DATA1__SD1_DATA1,
- MX51_PAD_SD1_DATA2__SD1_DATA2,
- MX51_PAD_SD1_DATA3__SD1_DATA3,
- /* CD/WP from controller */
- MX51_PAD_GPIO1_0__SD1_CD,
- MX51_PAD_GPIO1_1__SD1_WP,
-
- /* SD 2 */
- MX51_PAD_SD2_CMD__SD2_CMD,
- MX51_PAD_SD2_CLK__SD2_CLK,
- MX51_PAD_SD2_DATA0__SD2_DATA0,
- MX51_PAD_SD2_DATA1__SD2_DATA1,
- MX51_PAD_SD2_DATA2__SD2_DATA2,
- MX51_PAD_SD2_DATA3__SD2_DATA3,
- /* CD/WP gpio */
- MX51_PAD_GPIO1_6__GPIO1_6,
- MX51_PAD_GPIO1_5__GPIO1_5,
-
- /* eCSPI1 */
- MX51_PAD_CSPI1_MISO__ECSPI1_MISO,
- MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI,
- MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK,
- MX51_PAD_CSPI1_SS0__GPIO4_24,
- MX51_PAD_CSPI1_SS1__GPIO4_25,
-
- /* Audio */
- MX51_PAD_AUD3_BB_TXD__AUD3_TXD,
- MX51_PAD_AUD3_BB_RXD__AUD3_RXD,
- MX51_PAD_AUD3_BB_CK__AUD3_TXC,
- MX51_PAD_AUD3_BB_FS__AUD3_TXFS,
-};
-
-/* Serial ports */
-static const struct imxuart_platform_data uart_pdata __initconst = {
- .flags = IMXUART_HAVE_RTSCTS,
-};
-
-static const struct imxi2c_platform_data babbage_i2c_data __initconst = {
- .bitrate = 100000,
-};
-
-static const struct imxi2c_platform_data babbage_hsi2c_data __initconst = {
- .bitrate = 400000,
-};
-
-static struct gpio mx51_babbage_usbh1_gpios[] = {
- { BABBAGE_USBH1_STP, GPIOF_OUT_INIT_LOW, "usbh1_stp" },
- { BABBAGE_USB_PHY_RESET, GPIOF_OUT_INIT_LOW, "usbh1_phy_reset" },
-};
-
-static int gpio_usbh1_active(void)
-{
- iomux_v3_cfg_t usbh1stp_gpio = MX51_PAD_USBH1_STP__GPIO1_27;
- int ret;
-
- /* Set USBH1_STP to GPIO and toggle it */
- mxc_iomux_v3_setup_pad(usbh1stp_gpio);
- ret = gpio_request_array(mx51_babbage_usbh1_gpios,
- ARRAY_SIZE(mx51_babbage_usbh1_gpios));
-
- if (ret) {
- pr_debug("failed to get USBH1 pins: %d\n", ret);
- return ret;
- }
-
- msleep(100);
- gpio_set_value(BABBAGE_USBH1_STP, 1);
- gpio_set_value(BABBAGE_USB_PHY_RESET, 1);
- gpio_free_array(mx51_babbage_usbh1_gpios,
- ARRAY_SIZE(mx51_babbage_usbh1_gpios));
- return 0;
-}
-
-static inline void babbage_usbhub_reset(void)
-{
- int ret;
-
- /* Reset USB hub */
- ret = gpio_request_one(BABBAGE_USB_HUB_RESET,
- GPIOF_OUT_INIT_LOW, "GPIO1_7");
- if (ret) {
- printk(KERN_ERR"failed to get GPIO_USB_HUB_RESET: %d\n", ret);
- return;
- }
-
- msleep(2);
- /* Deassert reset */
- gpio_set_value(BABBAGE_USB_HUB_RESET, 1);
-}
-
-static inline void babbage_fec_reset(void)
-{
- int ret;
-
- /* reset FEC PHY */
- ret = gpio_request_one(BABBAGE_FEC_PHY_RESET,
- GPIOF_OUT_INIT_LOW, "fec-phy-reset");
- if (ret) {
- printk(KERN_ERR"failed to get GPIO_FEC_PHY_RESET: %d\n", ret);
- return;
- }
- msleep(1);
- gpio_set_value(BABBAGE_FEC_PHY_RESET, 1);
-}
-
-/* This function is board specific as the bit mask for the plldiv will also
-be different for other Freescale SoCs, thus a common bitmask is not
-possible and cannot get place in /plat-mxc/ehci.c.*/
-static int initialize_otg_port(struct platform_device *pdev)
-{
- u32 v;
- void __iomem *usb_base;
- void __iomem *usbother_base;
-
- usb_base = ioremap(MX51_USB_OTG_BASE_ADDR, SZ_4K);
- if (!usb_base)
- return -ENOMEM;
- usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;
-
- /* Set the PHY clock to 19.2MHz */
- v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
- v &= ~MX5_USB_UTMI_PHYCTRL1_PLLDIV_MASK;
- v |= MX51_USB_PLL_DIV_19_2_MHZ;
- __raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
- iounmap(usb_base);
-
- mdelay(10);
-
- return mx51_initialize_usb_hw(0, MXC_EHCI_INTERNAL_PHY);
-}
-
-static int initialize_usbh1_port(struct platform_device *pdev)
-{
- u32 v;
- void __iomem *usb_base;
- void __iomem *usbother_base;
-
- usb_base = ioremap(MX51_USB_OTG_BASE_ADDR, SZ_4K);
- if (!usb_base)
- return -ENOMEM;
- usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;
-
- /* The clock for the USBH1 ULPI port will come externally from the PHY. */
- v = __raw_readl(usbother_base + MX51_USB_CTRL_1_OFFSET);
- __raw_writel(v | MX51_USB_CTRL_UH1_EXT_CLK_EN, usbother_base + MX51_USB_CTRL_1_OFFSET);
- iounmap(usb_base);
-
- mdelay(10);
-
- return mx51_initialize_usb_hw(1, MXC_EHCI_POWER_PINS_ENABLED |
- MXC_EHCI_ITC_NO_THRESHOLD);
-}
-
-static const struct mxc_usbh_platform_data dr_utmi_config __initconst = {
- .init = initialize_otg_port,
- .portsc = MXC_EHCI_UTMI_16BIT,
-};
-
-static const struct fsl_usb2_platform_data usb_pdata __initconst = {
- .operating_mode = FSL_USB2_DR_DEVICE,
- .phy_mode = FSL_USB2_PHY_UTMI_WIDE,
-};
-
-static const struct mxc_usbh_platform_data usbh1_config __initconst = {
- .init = initialize_usbh1_port,
- .portsc = MXC_EHCI_MODE_ULPI,
-};
-
-static bool otg_mode_host __initdata;
-
-static int __init babbage_otg_mode(char *options)
-{
- if (!strcmp(options, "host"))
- otg_mode_host = true;
- else if (!strcmp(options, "device"))
- otg_mode_host = false;
- else
- pr_info("otg_mode neither \"host\" nor \"device\". "
- "Defaulting to device\n");
- return 1;
-}
-__setup("otg_mode=", babbage_otg_mode);
-
-static struct spi_board_info mx51_babbage_spi_board_info[] __initdata = {
- {
- .modalias = "mtd_dataflash",
- .max_speed_hz = 25000000,
- .bus_num = 0,
- .chip_select = 1,
- .mode = SPI_MODE_0,
- .platform_data = NULL,
- },
-};
-
-static int mx51_babbage_spi_cs[] = {
- BABBAGE_ECSPI1_CS0,
- BABBAGE_ECSPI1_CS1,
-};
-
-static const struct spi_imx_master mx51_babbage_spi_pdata __initconst = {
- .chipselect = mx51_babbage_spi_cs,
- .num_chipselect = ARRAY_SIZE(mx51_babbage_spi_cs),
-};
-
-static const struct esdhc_platform_data mx51_babbage_sd1_data __initconst = {
- .cd_type = ESDHC_CD_CONTROLLER,
- .wp_type = ESDHC_WP_CONTROLLER,
-};
-
-static const struct esdhc_platform_data mx51_babbage_sd2_data __initconst = {
- .cd_gpio = BABBAGE_SD2_CD,
- .wp_gpio = BABBAGE_SD2_WP,
- .cd_type = ESDHC_CD_GPIO,
- .wp_type = ESDHC_WP_GPIO,
-};
-
-void __init imx51_babbage_common_init(void)
-{
- mxc_iomux_v3_setup_multiple_pads(mx51babbage_pads,
- ARRAY_SIZE(mx51babbage_pads));
-}
-
-/*
- * Board specific initialization.
- */
-static void __init mx51_babbage_init(void)
-{
- iomux_v3_cfg_t usbh1stp = MX51_PAD_USBH1_STP__USBH1_STP;
- iomux_v3_cfg_t power_key = NEW_PAD_CTRL(MX51_PAD_EIM_A27__GPIO2_21,
- PAD_CTL_SRE_FAST | PAD_CTL_DSE_HIGH);
-
- imx51_soc_init();
-
- imx51_babbage_common_init();
-
- imx51_add_imx_uart(0, &uart_pdata);
- imx51_add_imx_uart(1, NULL);
- imx51_add_imx_uart(2, &uart_pdata);
-
- babbage_fec_reset();
- imx51_add_fec(NULL);
-
- /* Set the PAD settings for the pwr key. */
- mxc_iomux_v3_setup_pad(power_key);
- imx_add_gpio_keys(&imx_button_data);
-
- imx51_add_imx_i2c(0, &babbage_i2c_data);
- imx51_add_imx_i2c(1, &babbage_i2c_data);
- imx51_add_hsi2c(&babbage_hsi2c_data);
-
- if (otg_mode_host)
- imx51_add_mxc_ehci_otg(&dr_utmi_config);
- else {
- initialize_otg_port(NULL);
- imx51_add_fsl_usb2_udc(&usb_pdata);
- }
-
- gpio_usbh1_active();
- imx51_add_mxc_ehci_hs(1, &usbh1_config);
- /* setback USBH1_STP to be function */
- mxc_iomux_v3_setup_pad(usbh1stp);
- babbage_usbhub_reset();
-
- imx51_add_sdhci_esdhc_imx(0, &mx51_babbage_sd1_data);
- imx51_add_sdhci_esdhc_imx(1, &mx51_babbage_sd2_data);
-
- spi_register_board_info(mx51_babbage_spi_board_info,
- ARRAY_SIZE(mx51_babbage_spi_board_info));
- imx51_add_ecspi(0, &mx51_babbage_spi_pdata);
- imx51_add_imx2_wdt(0);
-}
-
-static void __init mx51_babbage_timer_init(void)
-{
- mx51_clocks_init(32768, 24000000, 22579200, 0);
-}
-
-MACHINE_START(MX51_BABBAGE, "Freescale MX51 Babbage Board")
- /* Maintainer: Amit Kucheria <amit.kucheria at canonical.com> */
- .atag_offset = 0x100,
- .map_io = mx51_map_io,
- .init_early = imx51_init_early,
- .init_irq = mx51_init_irq,
- .handle_irq = imx51_handle_irq,
- .init_time = mx51_babbage_timer_init,
- .init_machine = mx51_babbage_init,
- .init_late = imx51_init_late,
- .restart = mxc_restart,
-MACHINE_END
--
1.8.3.2
More information about the linux-arm-kernel
mailing list