[PATCH v4 1/2] video: ARM CLCD: Add DT support
Jean-Christophe PLAGNIOL-VILLARD
plagnioj at jcrosoft.com
Fri Sep 27 09:51:53 EDT 2013
On 15:19 Fri 20 Sep , Pawel Moll wrote:
> This patch adds basic DT bindings for the PL11x CLCD cells
> and make their fbdev driver use them.
>
> Signed-off-by: Pawel Moll <pawel.moll at arm.com>
> ---
> Changes since v3:
> - changed wording and order of interrupt-names and interrupts
> properties documentation
> - changed wording of arm,pl11x,framebuffer-base property
> documentation
> - cleaned up binding documentation indentation
>
> Changes since v2:
> - replaced video-ram phandle with arm,pl11x,framebuffer-base
> - replaced panel-* properties with arm,pl11x,panel-data-pads
> - replaced max-framebuffer-size with max-memory-bandwidth
> - modified clcdfb_of_init_tft_panel() to use the pads
> data and take differences between PL110 and PL110 into
> account
>
> Changes since v1:
> - minor code cleanups as suggested by Sylwester Nawrocki
> .../devicetree/bindings/video/arm,pl11x.txt | 145 +++++++++++
> .../devicetree/bindings/video/arm,pl11x.txt | 146 +++++++++++
> drivers/video/Kconfig | 1 +
> drivers/video/amba-clcd.c | 268 +++++++++++++++++++++
> 3 files changed, 415 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/video/arm,pl11x.txt
>
> diff --git a/Documentation/devicetree/bindings/video/arm,pl11x.txt b/Documentation/devicetree/bindings/video/arm,pl11x.txt
> new file mode 100644
> index 0000000..247e120
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/video/arm,pl11x.txt
> @@ -0,0 +1,146 @@
> +* ARM PrimeCell Color LCD Controller PL110/PL111
> +
> +See also Documentation/devicetree/bindings/arm/primecell.txt
> +
> +Required properties:
> +
> +- compatible: must be one of:
> + "arm,pl110", "arm,primecell"
> + "arm,pl111", "arm,primecell"
> +
> +- reg: base address and size of the control registers block
> +
> +- interrupt-names: either the single entry "combined" representing a
> + combined interrupt output (CLCDINTR), or the four entries
> + "mbe", "vcomp", "lnbu", "fuf" representing the individual
> + CLCDMBEINTR, CLCDVCOMPINTR, CLCDLNBUINTR, CLCDFUFINTR interrupts
> +
> +- interrupts: contains an interrupt specifier for each entry in
> + interrupt-names
> +
> +- clocks names: should contain "clcdclk" and "apb_pclk"
> +
> +- clocks: contains phandle and clock specifier pairs for the entries
> + in the clock-names property. See
> + Documentation/devicetree/binding/clock/clock-bindings.txt
> +
> +- arm,pl11x,panel-data-pads: array of 24 cells, each of them describing
> + a function of one of the CLD pads, starting from 0 up to 23;
> + each pad can be described by one of the following values:
> + - 0: reserved (not connected)
> + - 0x100-0x107: color upper STN panel data 0 to 7
> + - 0x110-0x117: color lower STN panel data 0 to 7
> + - 0x200-0x207: mono upper STN panel data 0 to 7
> + - 0x210-0x217: mono lower STN panel data 0 to 7
> + - 0x300-0x307: red component bit 0 to 7 of TFT panel data
> + - 0x310-0x317: green component bit 0 to 7 of TFT panel data
> + - 0x320-0x327: blue component bit 0 to 7 of TFT panel data
> + - 0x330: intensity bit of TFT panel data
sorry Paul for the late comment but those magic are really anoyoing please use
DT macro to make it readable
and maybe you can use phandle to drop the possible duplication across baords
> + Example sets of values for standard panel interfaces:
> + - PL110 single colour STN panel:
> + <0x107 0x106 0x105 0x104 0x103 0x102 0x101 0x100>,
> + <0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0>;
> + - PL110 dual colour STN panel:
> + <0x107 0x106 0x105 0x104 0x103 0x102 0x101 0x100>,
> + <0x117 0x116 0x115 0x114 0x113 0x112 0x111 0x110>,
> + <0 0 0 0 0 0 0 0>;
> + - PL110 single mono 4-bit STN panel:
> + <0x203 0x202 0x201 0x200>,
> + <0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0>;
> + - PL110 dual mono 4-bit STN panel:
> + <0x203 0x202 0x201 0x200>, <0 0 0 0>,
> + <0x213 0x212 0x211 0x210>,
> + <0 0 0 0 0 0 0 0 0 0 0 0>;
> + - PL110 single mono 8-bit STN panel:
> + <0x207 0x206 0x205 0x204 0x203 0x202 0x201 0x200>,
> + <0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0>;
> + - PL110 dual mono 8-bit STN panel:
> + <0x207 0x206 0x205 0x204 0x203 0x202 0x201 0x200>,
> + <0x217 0x216 0x215 0x214 0x213 0x212 0x211 0x210>,
> + <0 0 0 0 0 0 0 0>;
> + - PL110 TFT (1:)5:5:5 panel:
> + <0x330 0x300 0x301 0x302 0x303 0x304>,
> + <0x330 0x310 0x311 0x312 0x313 0x314>,
> + <0x330 0x320 0x321 0x322 0x323 0x324>,
> + <0 0 0 0 0 0>
> + - PL110 and PL111 TFT RGB 888 panel:
> + <0x300 0x301 0x302 0x303 0x304 0x305 0x306 0x307>,
> + <0x310 0x311 0x312 0x313 0x314 0x315 0x316 0x317>,
> + <0x320 0x321 0x322 0x323 0x324 0x325 0x326 0x327>;
> + - PL111 single colour STN panel:
> + <0x100 0x101 0x102 0x103 0x104 0x105 0x106 0x107>,
> + <0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0>;
> + - PL111 dual colour STN panel:
> + <0x100 0x101 0x102 0x103 0x104 0x105 0x106 0x107>,
> + <0x110 0x111 0x112 0x113 0x114 0x115 0x116 0x117>,
> + <0 0 0 0 0 0 0 0>;
> + - PL111 single mono 4-bit STN panel:
> + <0x200 0x201 0x202 0x203>,
> + <0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0>;
> + - PL111 dual mono 4-bit STN panel:
> + <0x200 0x201 0x202 0x203>, <0 0 0 0>,
> + <0x210 0x211 0x212 0x213>,
> + <0 0 0 0 0 0 0 0 0 0 0 0>;
> + - PL111 single mono 8-bit STN panel:
> + <0x200 0x201 0x202 0x203 0x204 0x205 0x206 0x207>,
> + <0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0>;
> + - PL111 dual mono 8-bit STN panel:
> + <0x200 0x201 0x202 0x203 0x204 0x205 0x206 0x207>,
> + <0x210 0x211 0x212 0x213 0x214 0x215 0x216 0x217>,
> + <0 0 0 0 0 0 0 0>;
> + - PL111 TFT 4:4:4 panel:
> + <0 0 0 0>, <0x300 0x301 0x302 0x303>,
> + <0 0 0 0>, <0x310 0x311 0x312 0x313>,
> + <0 0 0 0>, <0x320 0x321 0x322 0x323>;
> + - PL111 TFT 5:6:5 panel:
> + <0 0 0>, <0x300 0x301 0x302 0x303 0x304>,
> + <0 0>, <0x310 0x311 0x312 0x313 0x314 0x315>,
> + <0 0 0>, <0x320 0x321 0x322 0x323 0x324>;
> + - PL111 TFT (1):5:5:5 panel:
> + <0 0 0>, <0x300 0x301 0x302 0x303 0x304>,
> + <0 0>, <0x330 0x310 0x311 0x312 0x313 0x314>,
> + <0 0 0>, <0x320 0x321 0x322 0x323 0x324>;
> +
> +Optional properties:
> +
> +- arm,pl11x,framebuffer-base: a pair of two values, address and size,
> + defining the framebuffer that must be used; if not present, the
> + framebuffer may be located anywhere in the memory
this should be named ressources not a property for me
> +
> +- max-memory-bandwidth: maximum bandwidth in bytes per second that the
> + cell's memory interface can handle
> +
> +- display-timings: standard display timings sub-node, defining possible
> + video modes of a connected panel; for details see
> + Documentation/devicetree/bindings/video/display-timing.txt
> +
> +Example:
> +
> + clcd at 1f0000 {
> + compatible = "arm,pl111", "arm,primecell";
> + reg = <0x1f0000 0x1000>;
> + interrupt-names = "combined";
> + interrupts = <14>;
> + clock-names = "clcdclk", "apb_pclk";
> + clocks = <&v2m_oscclk1>, <&smbclk>;
> +
> + arm,pl11x,panel-data-pads = <0x300 0x301 0x302 0x303 0x304 0x305 0x306 0x307>,
> + <0x310 0x311 0x312 0x313 0x314 0x315 0x316 0x317>,
> + <0x320 0x321 0x322 0x323 0x324 0x325 0x326 0x327>;
> + arm,pl11x,framebuffer-base = <0x18000000 0x00800000>;
> + max-memory-bandwidth = <36864000>; /* bps, 640x480 at 60 16bpp */
> + display-timings {
> + native-mode = <&v2m_clcd_timing0>;
> + v2m_clcd_timing0: vga {
> + clock-frequency = <25175000>;
> + hactive = <640>;
> + hback-porch = <40>;
> + hfront-porch = <24>;
> + hsync-len = <96>;
> + vactive = <480>;
> + vback-porch = <32>;
> + vfront-porch = <11>;
> + vsync-len = <2>;
> + };
> + };
> + };
> diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
> index 84b685f..b7d8c23 100644
> --- a/drivers/video/Kconfig
> +++ b/drivers/video/Kconfig
> @@ -316,6 +316,7 @@ config FB_ARMCLCD
> select FB_CFB_FILLRECT
> select FB_CFB_COPYAREA
> select FB_CFB_IMAGEBLIT
> + select VIDEOMODE_HELPERS if OF
> help
> This framebuffer device driver is for the ARM PrimeCell PL110
> Colour LCD controller. ARM PrimeCells provide the building
> diff --git a/drivers/video/amba-clcd.c b/drivers/video/amba-clcd.c
> index 0a2cce7..03420d1 100644
> --- a/drivers/video/amba-clcd.c
> +++ b/drivers/video/amba-clcd.c
> @@ -25,6 +25,11 @@
> #include <linux/amba/clcd.h>
> #include <linux/clk.h>
> #include <linux/hardirq.h>
> +#include <linux/dma-mapping.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <video/of_display_timing.h>
> +#include <video/of_videomode.h>
>
> #include <asm/sizes.h>
>
> @@ -542,6 +547,266 @@ static int clcdfb_register(struct clcd_fb *fb)
> return ret;
> }
>
> +#ifdef CONFIG_OF
> +
> +#define CLCD_PADS_NUM 24
> +
> +#define CLCD_PAD_BIT(pad) ((pad) & 0xf)
> +#define CLCD_PAD_TYPE(pad) (((pad) >> 8) & 0xf)
> +
> +#define CLCD_PAD_IS_TFT(pad) (CLCD_PAD_TYPE(pad) == 0x3)
> +
> +#define CLCD_PAD_RGB(pad) (((pad) >> 4) & 0xf)
> +#define CLCD_PAD_R 0x0
> +#define CLCD_PAD_G 0x1
> +#define CLCD_PAD_B 0x2
> +
> +static int clcdfb_of_init_tft_panel(struct clcd_fb *fb, u32 *pads)
> +{
> + static struct {
> + unsigned int part;
> + int r0, g0, b0;
> + u32 caps;
> + } panels[] = {
> + { 0x110, 1, 7, 13, CLCD_CAP_5551 },
> + { 0x110, 0, 8, 16, CLCD_CAP_888 },
> + { 0x111, 4, 14, 20, CLCD_CAP_444 },
> + { 0x111, 3, 11, 19, CLCD_CAP_444 | CLCD_CAP_5551 },
> + { 0x111, 3, 10, 19, CLCD_CAP_444 | CLCD_CAP_5551 |
> + CLCD_CAP_565 },
> + { 0x111, 0, 8, 16, CLCD_CAP_444 | CLCD_CAP_5551 |
> + CLCD_CAP_565 | CLCD_CAP_888 },
> + };
> + int r = 0, g = 0, b = 0;
> + int r0 = -1, g0 = -1, b0 = -1;
> + int i;
> +
> + /* Bypass pixel clock divider, data output on the falling edge */
> + fb->panel->tim2 = TIM2_BCD | TIM2_IPC;
> +
> + /* TFT display, vert. comp. interrupt at the start of the back porch */
> + fb->panel->cntl |= CNTL_LCDTFT | CNTL_LCDVCOMP(1);
> +
> + fb->panel->caps = 0;
> +
> + /*
> + * Find indices of the first component bits and make sure they
> + * are in correct order
> + */
> + for (i = 0; i < CLCD_PADS_NUM; i++) {
> + int bit;
> +
> + if (!pads[i])
> + continue;
> + switch (CLCD_PAD_RGB(pads[i])) {
> + case CLCD_PAD_R:
> + r0 = r ? r0 : i;
> + bit = r++;
> + break;
> + case CLCD_PAD_G:
> + g0 = g ? g0 : i;
> + bit = g++;
> + break;
> + case CLCD_PAD_B:
> + b0 = b ? b0 : i;
> + bit = b++;
> + break;
> + default:
> + return -EINVAL;
> + }
> + if (bit != CLCD_PAD_BIT(pads[i]) || !CLCD_PAD_IS_TFT(pads[i]))
> + return -EINVAL;
> + }
> +
> + /* Match the setup with known variants */
> + for (i = 0; i < ARRAY_SIZE(panels) && !fb->panel->caps; i++) {
> + if (amba_part(fb->dev) != panels[i].part)
> + continue;
> + if (g0 != panels[i].g0)
> + continue;
> + if (r0 == panels[i].r0 && b0 == panels[i].b0)
> + fb->panel->caps = panels[i].caps & CLCD_CAP_RGB;
> + if (r0 == panels[i].b0 && b0 == panels[i].r0)
> + fb->panel->caps = panels[i].caps & CLCD_CAP_BGR;
> + }
> +
> + return fb->panel->caps ? 0 : -EINVAL;
> +}
> +
> +static int clcdfb_snprintf_mode(char *buf, int size, struct fb_videomode *mode)
> +{
> + return snprintf(buf, size, "%ux%u@%u", mode->xres, mode->yres,
> + mode->refresh);
> +}
> +
> +static int clcdfb_of_init_display(struct clcd_fb *fb)
> +{
> + struct device_node *node = fb->dev->dev.of_node;
> + int err, len;
> + char *mode_name;
> + u32 max_bandwidth;
> + u32 pads[CLCD_PADS_NUM];
> + int i;
> +
> + fb->panel = devm_kzalloc(&fb->dev->dev, sizeof(*fb->panel), GFP_KERNEL);
> + if (!fb->panel)
> + return -ENOMEM;
> +
> + err = of_get_fb_videomode(node, &fb->panel->mode, OF_USE_NATIVE_MODE);
> + if (err)
> + return err;
> +
> + len = clcdfb_snprintf_mode(NULL, 0, &fb->panel->mode);
> + mode_name = devm_kzalloc(&fb->dev->dev, len + 1, GFP_KERNEL);
> + clcdfb_snprintf_mode(mode_name, len + 1, &fb->panel->mode);
> + fb->panel->mode.name = mode_name;
> +
> + err = of_property_read_u32(node, "max-memory-bandwidth",
> + &max_bandwidth);
> + if (!err)
> + fb->panel->bpp = 8 * max_bandwidth / (fb->panel->mode.xres *
> + fb->panel->mode.yres * fb->panel->mode.refresh);
> + else
> + fb->panel->bpp = 32;
> +
> +#ifdef CONFIG_CPU_BIG_ENDIAN
if (IS_ENABLED(xxx))
> + fb->panel->cntl |= CNTL_BEBO;
> +#endif
> + fb->panel->width = -1;
> + fb->panel->height = -1;
> +
> + err = of_property_read_u32_array(node, "arm,pl11x,panel-data-pads",
> + pads, ARRAY_SIZE(pads));
> + if (err)
> + return err;
> +
> + /* Find first connected pad - its type determines the panel */
> + for (i = 0; i < CLCD_PADS_NUM; i++)
> + if (pads[i] && CLCD_PAD_IS_TFT(pads[i]))
> + return clcdfb_of_init_tft_panel(fb, pads);
> +
> + return -EINVAL;
> +}
> +
> +static int clcdfb_of_vram_setup(struct clcd_fb *fb)
> +{
> + int err;
> + u32 values[2];
> + phys_addr_t phys_base;
> + size_t size;
> +
> + err = clcdfb_of_init_display(fb);
> + if (err)
> + return err;
> +
> + err = of_property_read_u32_array(fb->dev->dev.of_node,
> + "arm,pl11x,framebuffer-base",
> + values, ARRAY_SIZE(values));
> + if (err)
> + return err;
> +
> + phys_base = values[0];
> + size = values[1];
> +
> + fb->fb.screen_base = ioremap(phys_base, size);
> + if (!fb->fb.screen_base)
> + return -ENOMEM;
> +
> + fb->fb.fix.smem_start = phys_base;
> + fb->fb.fix.smem_len = size;
> +
> + return 0;
> +}
> +
> +static int clcdfb_of_vram_mmap(struct clcd_fb *fb, struct vm_area_struct *vma)
> +{
> + unsigned long off, user_size, kernel_size;
> +
> + off = vma->vm_pgoff << PAGE_SHIFT;
> + user_size = vma->vm_end - vma->vm_start;
> + kernel_size = fb->fb.fix.smem_len;
> +
> + if (off >= kernel_size || user_size > (kernel_size - off))
> + return -ENXIO;
> +
> + return remap_pfn_range(vma, vma->vm_start,
> + __phys_to_pfn(fb->fb.fix.smem_start) + vma->vm_pgoff,
> + user_size,
> + pgprot_writecombine(vma->vm_page_prot));
> +}
> +
> +static void clcdfb_of_vram_remove(struct clcd_fb *fb)
> +{
> + iounmap(fb->fb.screen_base);
> +}
> +
> +static int clcdfb_of_dma_setup(struct clcd_fb *fb)
> +{
> + unsigned long framesize;
> + dma_addr_t dma;
> + int err;
> +
> + err = clcdfb_of_init_display(fb);
> + if (err)
> + return err;
> +
> + framesize = fb->panel->mode.xres * fb->panel->mode.yres *
> + fb->panel->bpp / 8;
> + fb->fb.screen_base = dma_alloc_writecombine(&fb->dev->dev, framesize,
> + &dma, GFP_KERNEL);
> + if (!fb->fb.screen_base)
> + return -ENOMEM;
> +
> + fb->fb.fix.smem_start = dma;
> + fb->fb.fix.smem_len = framesize;
> +
> + return 0;
> +}
> +
> +static int clcdfb_of_dma_mmap(struct clcd_fb *fb, struct vm_area_struct *vma)
> +{
> + return dma_mmap_writecombine(&fb->dev->dev, vma, fb->fb.screen_base,
> + fb->fb.fix.smem_start, fb->fb.fix.smem_len);
> +}
> +
> +static void clcdfb_of_dma_remove(struct clcd_fb *fb)
> +{
> + dma_free_writecombine(&fb->dev->dev, fb->fb.fix.smem_len,
> + fb->fb.screen_base, fb->fb.fix.smem_start);
> +}
> +
> +static struct clcd_board *clcdfb_of_get_board(struct amba_device *dev)
> +{
> + struct clcd_board *board = devm_kzalloc(&dev->dev, sizeof(*board),
> + GFP_KERNEL);
> + struct device_node *node = dev->dev.of_node;
> +
> + if (!board)
> + return NULL;
> +
> + board->name = of_node_full_name(node);
> + board->caps = CLCD_CAP_ALL;
> + board->check = clcdfb_check;
> + board->decode = clcdfb_decode;
> + if (of_find_property(node, "arm,pl11x,framebuffer-base", NULL)) {
> + board->setup = clcdfb_of_vram_setup;
> + board->mmap = clcdfb_of_vram_mmap;
> + board->remove = clcdfb_of_vram_remove;
> + } else {
> + board->setup = clcdfb_of_dma_setup;
> + board->mmap = clcdfb_of_dma_mmap;
> + board->remove = clcdfb_of_dma_remove;
> + }
> +
> + return board;
> +}
> +#else
> +static struct clcd_board *clcdfb_of_get_board(struct amba_dev *dev)
> +{
> + return NULL;
> +}
> +#endif
> +
> static int clcdfb_probe(struct amba_device *dev, const struct amba_id *id)
> {
> struct clcd_board *board = dev->dev.platform_data;
> @@ -549,6 +814,9 @@ static int clcdfb_probe(struct amba_device *dev, const struct amba_id *id)
> int ret;
>
> if (!board)
> + board = clcdfb_of_get_board(dev);
> +
> + if (!board)
> return -EINVAL;
>
> ret = amba_request_regions(dev, NULL);
> --
> 1.8.1.2
>
>
More information about the linux-arm-kernel
mailing list