[PATCHv3 2/4] ARM: dts: Add Freescale FTM PWM node for VF610.

[Sascha Hauer]

On Fri, Sep 06, 2013 at 04:08:25PM +0800, Xiubo Li wrote:
> This adds devicetree node for VF610, and there are 8 channels supported
> by default.
> 
> Signed-off-by: Xiubo Li <Li.Xiubo at freescale.com>
> ---
>  arch/arm/boot/dts/vf610.dtsi | 103 ++++++++++++++++++++++++++++++++++++++++++-
>  1 file changed, 102 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm/boot/dts/vf610.dtsi b/arch/arm/boot/dts/vf610.dtsi
> index 67d929c..44787b5 100644
> --- a/arch/arm/boot/dts/vf610.dtsi
> +++ b/arch/arm/boot/dts/vf610.dtsi
> @@ -140,6 +140,37 @@
>  				clock-names = "pit";
>  			};
>  
> +			pwm0: pwm at 40038000 {
> +				compatible = "fsl,vf610-ftm-pwm";
> +				#pwm-cells = <3>;
> +				reg = <0x40038000 0x1000>;
> +				clock-names = "ftm0", "ftm0_fix_sel", "ftm0_ext_sel";
> +				clocks = <&clks VF610_CLK_FTM0>,
> +					<&clks VF610_CLK_FTM0_FIX_SEL>,
> +					<&clks VF610_CLK_FTM0_EXT_SEL>;
> +				pinctrl-names = "ch0-active", "ch0-idle", "ch1-active", "ch1-idle",
> +						"ch2-active", "ch2-idle", "ch3-active", "ch3-idle",
> +						"ch4-active", "ch4-idle", "ch5-active", "ch5-idle",
> +						"ch6-active", "ch6-idle", "ch7-active", "ch7-idle";
> +				pinctrl-0 = <&pinctrl_pwm0_ch0_active>;
> +				pinctrl-1 = <&pinctrl_pwm0_ch0_idle>;
> +				pinctrl-2 = <&pinctrl_pwm0_ch1_active>;
> +				pinctrl-3 = <&pinctrl_pwm0_ch1_idle>;
> +				pinctrl-4 = <&pinctrl_pwm0_ch2_active>;
> +				pinctrl-5 = <&pinctrl_pwm0_ch2_idle>;
> +				pinctrl-6 = <&pinctrl_pwm0_ch3_active>;
> +				pinctrl-7 = <&pinctrl_pwm0_ch3_idle>;
> +				pinctrl-8 = <&pinctrl_pwm0_ch4_active>;
> +				pinctrl-9 = <&pinctrl_pwm0_ch4_idle>;
> +				pinctrl-10 = <&pinctrl_pwm0_ch5_active>;
> +				pinctrl-11 = <&pinctrl_pwm0_ch5_idle>;
> +				pinctrl-12 = <&pinctrl_pwm0_ch6_active>;
> +				pinctrl-13 = <&pinctrl_pwm0_ch6_idle>;
> +				pinctrl-14 = <&pinctrl_pwm0_ch7_active>;
> +				pinctrl-15 = <&pinctrl_pwm0_ch7_idle>;
> +				status = "disabled";
> +			};

This is a SoC file, but the pinmux is board specific. The pinmux
settings probably shouldn't be here.

Sascha

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |