[PATCH 5/5] Staging/iio/adc/touchscreen/MXS: Remove old touchscreen detection implementation
Juergen Beisert
jbe at pengutronix.de
Fri Sep 6 06:08:43 EDT 2013
Signed-off-by: Juergen Beisert <jbe at pengutronix.de>
CC: linux-arm-kernel at lists.infradead.org
CC: devel at driverdev.osuosl.org
CC: Marek Vasut <marex at denx.de>
CC: Fabio Estevam <fabio.estevam at freescale.com>
CC: Jonathan Cameron <jic23 at cam.ac.uk>
---
drivers/staging/iio/adc/mxs-lradc.c | 165 ------------------------------------
1 file changed, 165 deletions(-)
diff --git a/drivers/staging/iio/adc/mxs-lradc.c b/drivers/staging/iio/adc/mxs-lradc.c
index 28b5ea4..638a228 100644
--- a/drivers/staging/iio/adc/mxs-lradc.c
+++ b/drivers/staging/iio/adc/mxs-lradc.c
@@ -183,7 +183,6 @@ struct mxs_lradc {
bool use_touchbutton;
struct input_dev *ts_input;
- struct work_struct ts_work;
enum mxs_lradc_id soc;
enum lradc_ts_plate cur_plate; /* statemachine */
@@ -837,168 +836,6 @@ static const struct iio_info mxs_lradc_iio_info = {
.read_raw = mxs_lradc_read_raw,
};
-static int mxs_lradc_ts_touched(struct mxs_lradc *lradc)
-{
- uint32_t reg;
-
- /* Enable touch detection. */
- mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
- mxs_lradc_reg_set(lradc, mxs_lradc_touch_detect_bit(lradc),
- LRADC_CTRL0);
-
- msleep(LRADC_TS_SAMPLE_DELAY_MS);
-
- reg = readl(lradc->base + LRADC_STATUS);
-
- return reg & LRADC_STATUS_TOUCH_DETECT_RAW;
-}
-
-static int32_t mxs_lradc_ts_sample(struct mxs_lradc *lradc,
- enum lradc_ts_plate plate, int change)
-{
- unsigned long delay, jiff;
- uint32_t reg, ctrl0 = 0, chan = 0;
- /* The touchscreen always uses CTRL4 slot #7. */
- const uint8_t slot = 7;
- uint32_t val;
-
- /*
- * There are three correct configurations of the controller sampling
- * the touchscreen, each of these configuration provides different
- * information from the touchscreen.
- *
- * The following table describes the sampling configurations:
- * +-------------+-------+-------+-------+
- * | Wire \ Axis | X | Y | Z |
- * +---------------------+-------+-------+
- * | X+ (CH2) | HI | TS | TS |
- * +-------------+-------+-------+-------+
- * | X- (CH4) | LO | SH | HI |
- * +-------------+-------+-------+-------+
- * | Y+ (CH3) | SH | HI | HI |
- * +-------------+-------+-------+-------+
- * | Y- (CH5) | TS | LO | SH |
- * +-------------+-------+-------+-------+
- *
- * HI ... strong '1' ; LO ... strong '0'
- * SH ... sample here ; TS ... tri-state
- *
- * There are a few other ways of obtaining the Z coordinate
- * (aka. pressure), but the one in the table seems to be the
- * most reliable one.
- */
- switch (plate) {
- case LRADC_SAMPLE_X:
- ctrl0 = mxs_lradc_drive_x_plate(lradc);
- chan = 3;
- break;
- case LRADC_SAMPLE_Y:
- ctrl0 = mxs_lradc_drive_y_plate(lradc);
- chan = 4;
- break;
- case LRADC_SAMPLE_PRESSURE:
- ctrl0 = mxs_lradc_drive_pressure(lradc);
- chan = 5;
- break;
- }
-
- if (change) {
- mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc),
- LRADC_CTRL0);
- mxs_lradc_reg_set(lradc, ctrl0, LRADC_CTRL0);
-
- mxs_lradc_reg_clear(lradc, LRADC_CTRL4_LRADCSELECT_MASK(slot),
- LRADC_CTRL4);
- mxs_lradc_reg_set(lradc,
- chan << LRADC_CTRL4_LRADCSELECT_OFFSET(slot),
- LRADC_CTRL4);
- }
-
- mxs_lradc_reg_clear(lradc, 0xffffffff, LRADC_CH(slot));
- mxs_lradc_reg_set(lradc, 1 << slot, LRADC_CTRL0);
-
- delay = jiffies + msecs_to_jiffies(LRADC_TS_SAMPLE_DELAY_MS);
- do {
- jiff = jiffies;
- reg = readl_relaxed(lradc->base + LRADC_CTRL1);
- if (reg & LRADC_CTRL1_LRADC_IRQ(slot))
- break;
- } while (time_before(jiff, delay));
-
- mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ(slot), LRADC_CTRL1);
-
- if (time_after_eq(jiff, delay))
- return -ETIMEDOUT;
-
- val = readl(lradc->base + LRADC_CH(slot));
- val &= LRADC_CH_VALUE_MASK;
-
- return val;
-}
-
-static int32_t mxs_lradc_ts_sample_filter(struct mxs_lradc *lradc,
- enum lradc_ts_plate plate)
-{
- int32_t val, tot = 0;
- int i;
-
- val = mxs_lradc_ts_sample(lradc, plate, 1);
-
- /* Delay a bit so the touchscreen is stable. */
- mdelay(2);
-
- for (i = 0; i < LRADC_TS_SAMPLE_AMOUNT; i++) {
- val = mxs_lradc_ts_sample(lradc, plate, 0);
- tot += val;
- }
-
- return tot / LRADC_TS_SAMPLE_AMOUNT;
-}
-
-static void mxs_lradc_ts_work(struct work_struct *ts_work)
-{
- struct mxs_lradc *lradc = container_of(ts_work,
- struct mxs_lradc, ts_work);
- int val_x, val_y, val_p;
- bool valid = false;
-
- while (mxs_lradc_ts_touched(lradc)) {
- /* Disable touch detector so we can sample the touchscreen. */
- mxs_lradc_reg_clear(lradc, mxs_lradc_touch_detect_bit(lradc),
- LRADC_CTRL0);
-
- if (likely(valid)) {
- input_report_abs(lradc->ts_input, ABS_X, val_x);
- input_report_abs(lradc->ts_input, ABS_Y, val_y);
- input_report_abs(lradc->ts_input, ABS_PRESSURE, val_p);
- input_report_key(lradc->ts_input, BTN_TOUCH, 1);
- input_sync(lradc->ts_input);
- }
-
- valid = false;
-
- val_x = mxs_lradc_ts_sample_filter(lradc, LRADC_SAMPLE_X);
- if (val_x < 0)
- continue;
- val_y = mxs_lradc_ts_sample_filter(lradc, LRADC_SAMPLE_Y);
- if (val_y < 0)
- continue;
- val_p = mxs_lradc_ts_sample_filter(lradc, LRADC_SAMPLE_PRESSURE);
- if (val_p < 0)
- continue;
-
- valid = true;
- }
-
- input_report_abs(lradc->ts_input, ABS_PRESSURE, 0);
- input_report_key(lradc->ts_input, BTN_TOUCH, 0);
- input_sync(lradc->ts_input);
-
- /* Restart the touchscreen interrupts. */
- mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1);
- mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
-}
-
static int mxs_lradc_ts_open(struct input_dev *dev)
{
struct mxs_lradc *lradc = input_get_drvdata(dev);
@@ -1071,8 +908,6 @@ static void mxs_lradc_ts_unregister(struct mxs_lradc *lradc)
if (!lradc->use_touchscreen)
return;
- cancel_work_sync(&lradc->ts_work);
-
mxs_lradc_disable_ts(lradc);
input_unregister_device(lradc->ts_input);
}
--
1.8.4.rc3
More information about the linux-arm-kernel
mailing list