[PATCH 6/8] ARM: dts: Add basic support for zoom3
Tony Lindgren
tony at atomide.com
Thu Oct 10 18:20:55 EDT 2013
I've tested serial, MMC, smsc911x and wl12xx on zoom3. As my
omap is an early ES revision, I have not been able to test
off-idle on this one. But anyways, I'd say we have enough
device tree support for the zoom to be able to drop the
board-zoom files. Patches are welcome to add further features
to this .dts file.
Signed-off-by: Tony Lindgren <tony at atomide.com>
---
arch/arm/boot/dts/Makefile | 1
arch/arm/boot/dts/omap-zoom-common.dtsi | 33 +++++
arch/arm/boot/dts/omap3-zoom3.dts | 217 +++++++++++++++++++++++++++++++
3 files changed, 251 insertions(+)
create mode 100644 arch/arm/boot/dts/omap-zoom-common.dtsi
create mode 100644 arch/arm/boot/dts/omap3-zoom3.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 3c4e105..ce332c8 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -176,6 +176,7 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
omap3-tobi.dtb \
omap3-igep0020.dtb \
omap3-igep0030.dtb \
+ omap3-zoom3.dtb \
omap4-panda.dtb \
omap4-panda-a4.dtb \
omap4-panda-es.dtb \
diff --git a/arch/arm/boot/dts/omap-zoom-common.dtsi b/arch/arm/boot/dts/omap-zoom-common.dtsi
new file mode 100644
index 0000000..b0ee342
--- /dev/null
+++ b/arch/arm/boot/dts/omap-zoom-common.dtsi
@@ -0,0 +1,33 @@
+/*
+ * Common features on the Zoom debug board
+ */
+
+#include "omap-gpmc-smsc911x.dtsi"
+
+&gpmc {
+ ranges = <3 0 0x10000000 0x00000400>,
+ <7 0 0x2c000000 0x01000000>;
+
+ /*
+ * Four port TL16CP754C serial port on GPMC,
+ * they probably share the same GPIO IRQ
+ * REVISIT: Add timing support from slls644g.pdf
+ */
+ 8250 at 3,0 {
+ compatible = "ns16550a";
+ reg = <3 0 0x100>;
+ bank-width = <2>;
+ reg-shift = <1>;
+ reg-io-width = <1>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <6 IRQ_TYPE_EDGE_RISING>; /* gpio102 */
+ clock-frequency = <1843200>;
+ current-speed = <115200>;
+ };
+
+ ethernet at gpmc {
+ reg = <7 0 0xff>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <30 IRQ_TYPE_LEVEL_LOW>; /* gpio158 */
+ };
+};
diff --git a/arch/arm/boot/dts/omap3-zoom3.dts b/arch/arm/boot/dts/omap3-zoom3.dts
new file mode 100644
index 0000000..15eb9fe
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-zoom3.dts
@@ -0,0 +1,217 @@
+/*
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "omap36xx.dtsi"
+#include "omap-zoom-common.dtsi"
+
+/ {
+ model = "TI Zoom3";
+ compatible = "ti,omap3-zoom3", "ti,omap36xx", "ti,omap3";
+
+ cpus {
+ cpu at 0 {
+ cpu0-supply = <&vcc>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x20000000>; /* 512 MB */
+ };
+
+ vddvario: regulator-vddvario {
+ compatible = "regulator-fixed";
+ regulator-name = "vddvario";
+ regulator-always-on;
+ };
+
+ vdd33a: regulator-vdd33a {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd33a";
+ regulator-always-on;
+ };
+
+ wl12xx_vmmc: wl12xx_vmmc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&wl12xx_gpio>;
+ compatible = "regulator-fixed";
+ regulator-name = "vwl1271";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio4 5 0>; /* gpio101 */
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
+};
+
+&omap3_pmx_core {
+ /* REVISIT: twl gpio0 is mmc0_cd */
+ mmc1_pins: pinmux_mmc1_pins {
+ pinctrl-single,pins = <
+ 0x114 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */
+ 0x116 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */
+ 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
+ 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
+ 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
+ 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
+ >;
+ };
+
+ mmc2_pins: pinmux_mmc2_pins {
+ pinctrl-single,pins = <
+ 0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */
+ 0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */
+ 0x12c (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */
+ 0x12e (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
+ 0x130 (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
+ 0x132 (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
+ 0x134 (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat4.sdmmc2_dat4 */
+ 0x136 (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat5.sdmmc2_dat5 */
+ 0x138 (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat6.sdmmc2_dat6 */
+ 0x13a (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat7.sdmmc2_dat7 */
+ >;
+ };
+
+ mmc3_pins: pinmux_mmc3_pins {
+ pinctrl-single,pins = <
+ 0x168 (PIN_INPUT | MUX_MODE4) /* mcbsp1_clkx.gpio_162 WLAN IRQ */
+ 0x1a0 (PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs1.sdmmc3_cmd */
+ 0x5a8 (PIN_INPUT_PULLUP | MUX_MODE2) /* etk_clk.sdmmc3_clk */
+ 0x5b4 (PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d4.sdmmc3_dat0 */
+ 0x5b6 (WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d5.sdmmc3_dat1 */
+ 0x5b8 (PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d6.sdmmc3_dat2 */
+ 0x5b2 (PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d3.sdmmc3_dat3 */
+ >;
+ };
+
+ uart1_pins: pinmux_uart1_pins {
+ pinctrl-single,pins = <
+ 0x150 (PIN_INPUT | MUX_MODE0) /* uart1_cts.uart1_cts */
+ 0x14e (PIN_OUTPUT | MUX_MODE0) /* uart1_rts.uart1_rts */
+ 0x152 (WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart1_rx.uart1_rx */
+ 0x14c (PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_tx */
+ >;
+ };
+
+ uart2_pins: pinmux_uart2_pins {
+ pinctrl-single,pins = <
+ 0x144 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_cts.uart2_cts */
+ 0x146 (PIN_OUTPUT | MUX_MODE0) /* uart2_rts.uart2_rts */
+ 0x14a (WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */
+ 0x148 (PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */
+ >;
+ };
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ 0x16a (PIN_INPUT_PULLDOWN | MUX_MODE0) /* uart3_cts_rctx.uart3_cts_rctx */
+ 0x16c (PIN_OUTPUT | MUX_MODE0) /* uart3_rts_sd.uart3_rts_sd */
+ 0x16e (WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
+ 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
+ >;
+ };
+
+ /* wl12xx GPIO output for WLAN_EN */
+ wl12xx_gpio: pinmux_wl12xx_gpio {
+ pinctrl-single,pins = <
+ 0xea (PIN_OUTPUT| MUX_MODE4) /* cam_d2.gpio_101 */
+ >;
+ };
+};
+
+&omap3_pmx_wkup {
+ wlan_host_wkup: pinmux_wlan_host_wkup_pins {
+ pinctrl-single,pins = <
+ 0x1a (PIN_INPUT_PULLUP | MUX_MODE4) /* sys_clkout1.gpio_10 WLAN_HOST_WKUP */
+ >;
+ };
+};
+
+&i2c1 {
+ clock-frequency = <2600000>;
+
+ twl: twl at 48 {
+ reg = <0x48>;
+ interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+ interrupt-parent = <&intc>;
+ };
+};
+
+#include "twl4030.dtsi"
+
+&i2c2 {
+ clock-frequency = <400000>;
+};
+
+&i2c3 {
+ clock-frequency = <400000>;
+
+ /*
+ * TVP5146 Video decoder-in for analog input support.
+ */
+ tvp5146 at 5c {
+ compatible = "ti,tvp5146m2";
+ reg = <0x5c>;
+ };
+};
+
+&twl_gpio {
+ ti,use-leds;
+};
+
+&mmc1 {
+ vmmc-supply = <&vmmc1>;
+ vmmc_aux-supply = <&vsim>;
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+};
+/*
+&mmc2 {
+ vmmc-supply = <&vmmc2>;
+ ti,non-removable;
+ bus-width = <8>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>;
+};
+*/
+&mmc3 {
+ vmmc-supply = <&wl12xx_vmmc>;
+ non-removable;
+ bus-width = <4>;
+ cap-power-off-card;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins>;
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+};
+
+&uart4 {
+ status = "disabled";
+};
+
+&usb_otg_hs {
+ interface-type = <0>;
+ usb-phy = <&usb2_phy>;
+ mode = <3>;
+ power = <50>;
+};
More information about the linux-arm-kernel
mailing list