[PATCH v3 09/36] mtd: st_spi_fsm: Provide device look-up table
Lee Jones
lee.jones at linaro.org
Fri Nov 29 07:18:58 EST 2013
Supply a lookup table of all the devices we intend to support. This table
is used to store device information such as; a human readable device name,
their JEDEC ID (plus the extended version), sector size and amount, a bit
store of a device's capabilities, its maximum running frequency and
possible use of a per-device configuration call-back.
Signed-off-by: Lee Jones <lee.jones at linaro.org>
---
drivers/mtd/devices/st_spi_fsm.h | 137 +++++++++++++++++++++++++++++++++++++++
1 file changed, 137 insertions(+)
diff --git a/drivers/mtd/devices/st_spi_fsm.h b/drivers/mtd/devices/st_spi_fsm.h
index 5c6c55e..fd1472e 100644
--- a/drivers/mtd/devices/st_spi_fsm.h
+++ b/drivers/mtd/devices/st_spi_fsm.h
@@ -253,4 +253,141 @@ struct stfsm_seq {
} __attribute__((__packed__, aligned(4)));
#define STFSM_SEQ_SIZE sizeof(struct stfsm_seq)
+/* SPI Flash Device Table */
+struct flash_info {
+ char *name;
+ /*
+ * JEDEC id zero means "no ID" (most older chips); otherwise it has
+ * a high byte of zero plus three data bytes: the manufacturer id,
+ * then a two byte device id.
+ */
+ u32 jedec_id;
+ u16 ext_id;
+ /*
+ * The size listed here is what works with FLASH_CMD_SE, which isn't
+ * necessarily called a "sector" by the vendor.
+ */
+ unsigned sector_size;
+ u16 n_sectors;
+ u32 flags;
+ /*
+ * Note, where FAST_READ is supported, freq_max specifies the
+ * FAST_READ frequency, not the READ frequency.
+ */
+ u32 max_freq;
+ int (*config)(struct stfsm *);
+};
+
+static struct flash_info flash_types[] = {
+ /*
+ * ST Microelectronics/Numonyx --
+ * (newer production versions may have feature updates
+ * (eg faster operating frequency)
+ */
+#define M25P_FLAG (FLASH_FLAG_READ_WRITE | FLASH_FLAG_READ_FAST)
+ { "m25p40", 0x202013, 0, 64 * 1024, 8, M25P_FLAG, 25, NULL },
+ { "m25p80", 0x202014, 0, 64 * 1024, 16, M25P_FLAG, 25, NULL },
+ { "m25p16", 0x202015, 0, 64 * 1024, 32, M25P_FLAG, 25, NULL },
+ { "m25p32", 0x202016, 0, 64 * 1024, 64, M25P_FLAG, 50, NULL },
+ { "m25p64", 0x202017, 0, 64 * 1024, 128, M25P_FLAG, 50, NULL },
+ { "m25p128", 0x202018, 0, 256 * 1024, 64, M25P_FLAG, 50, NULL },
+
+#define M25PX_FLAG (FLASH_FLAG_READ_WRITE | \
+ FLASH_FLAG_READ_FAST | \
+ FLASH_FLAG_READ_1_1_2 | \
+ FLASH_FLAG_WRITE_1_1_2)
+ { "m25px32", 0x207116, 0, 64 * 1024, 64, M25PX_FLAG, 75, NULL },
+ { "m25px64", 0x207117, 0, 64 * 1024, 128, M25PX_FLAG, 75, NULL },
+
+#define MX25_FLAG (FLASH_FLAG_READ_WRITE | \
+ FLASH_FLAG_READ_FAST | \
+ FLASH_FLAG_READ_1_1_2 | \
+ FLASH_FLAG_READ_1_2_2 | \
+ FLASH_FLAG_READ_1_1_4 | \
+ FLASH_FLAG_READ_1_4_4 | \
+ FLASH_FLAG_WRITE_1_4_4 | \
+ FLASH_FLAG_SE_4K | \
+ FLASH_FLAG_SE_32K)
+ { "mx25l25635e", 0xc22019, 0, 64*1024, 512,
+ (MX25_FLAG | FLASH_FLAG_32BIT_ADDR | FLASH_FLAG_RESET), 70, NULL },
+
+#define N25Q_FLAG (FLASH_FLAG_READ_WRITE | \
+ FLASH_FLAG_READ_FAST | \
+ FLASH_FLAG_READ_1_1_2 | \
+ FLASH_FLAG_READ_1_2_2 | \
+ FLASH_FLAG_READ_1_1_4 | \
+ FLASH_FLAG_READ_1_4_4 | \
+ FLASH_FLAG_WRITE_1_1_2 | \
+ FLASH_FLAG_WRITE_1_2_2 | \
+ FLASH_FLAG_WRITE_1_1_4 | \
+ FLASH_FLAG_WRITE_1_4_4)
+ { "n25q128", 0x20ba18, 0, 64 * 1024, 256, N25Q_FLAG, 108, NULL },
+ { "n25q256", 0x20ba19, 0, 64 * 1024, 512,
+ N25Q_FLAG | FLASH_FLAG_32BIT_ADDR, 108, NULL },
+
+ /*
+ * Spansion S25FLxxxP
+ * - 256KiB and 64KiB sector variants (identified by ext. JEDEC)
+ */
+#define S25FLXXXP_FLAG (FLASH_FLAG_READ_WRITE | \
+ FLASH_FLAG_READ_1_1_2 | \
+ FLASH_FLAG_READ_1_2_2 | \
+ FLASH_FLAG_READ_1_1_4 | \
+ FLASH_FLAG_READ_1_4_4 | \
+ FLASH_FLAG_WRITE_1_1_4 | \
+ FLASH_FLAG_READ_FAST)
+ { "s25fl129p0", 0x012018, 0x4d00, 256 * 1024, 64, S25FLXXXP_FLAG, 80,
+ NULL },
+ { "s25fl129p1", 0x012018, 0x4d01, 64 * 1024, 256, S25FLXXXP_FLAG, 80,
+ NULL },
+
+ /*
+ * Spansion S25FLxxxS
+ * - 256KiB and 64KiB sector variants (identified by ext. JEDEC)
+ * - RESET# signal supported by die but not bristled out on all
+ * package types. The package type is a function of board design,
+ * so this information is captured in the board's flags.
+ * - Supports 'DYB' sector protection. Depending on variant, sectors
+ * may default to locked state on power-on.
+ */
+#define S25FLXXXS_FLAG (S25FLXXXP_FLAG | \
+ FLASH_FLAG_RESET | \
+ FLASH_FLAG_DYB_LOCKING)
+ { "s25fl128s0", 0x012018, 0x0300, 256 * 1024, 64, S25FLXXXS_FLAG, 80,
+ NULL },
+ { "s25fl128s1", 0x012018, 0x0301, 64 * 1024, 256, S25FLXXXS_FLAG, 80,
+ NULL },
+ { "s25fl256s0", 0x010219, 0x4d00, 256 * 1024, 128,
+ S25FLXXXS_FLAG | FLASH_FLAG_32BIT_ADDR, 80, NULL },
+ { "s25fl256s1", 0x010219, 0x4d01, 64 * 1024, 512,
+ S25FLXXXS_FLAG | FLASH_FLAG_32BIT_ADDR, 80, NULL },
+
+ /* Winbond -- w25x "blocks" are 64K, "sectors" are 4KiB */
+#define W25X_FLAG (FLASH_FLAG_READ_WRITE | \
+ FLASH_FLAG_READ_FAST | \
+ FLASH_FLAG_READ_1_1_2 | \
+ FLASH_FLAG_WRITE_1_1_2)
+ { "w25x40", 0xef3013, 0, 64 * 1024, 8, W25X_FLAG, 75, NULL },
+ { "w25x80", 0xef3014, 0, 64 * 1024, 16, W25X_FLAG, 75, NULL },
+ { "w25x16", 0xef3015, 0, 64 * 1024, 32, W25X_FLAG, 75, NULL },
+ { "w25x32", 0xef3016, 0, 64 * 1024, 64, W25X_FLAG, 75, NULL },
+ { "w25x64", 0xef3017, 0, 64 * 1024, 128, W25X_FLAG, 75, NULL },
+
+ /* Winbond -- w25q "blocks" are 64K, "sectors" are 4KiB */
+#define W25Q_FLAG (FLASH_FLAG_READ_WRITE | \
+ FLASH_FLAG_READ_FAST | \
+ FLASH_FLAG_READ_1_1_2 | \
+ FLASH_FLAG_READ_1_2_2 | \
+ FLASH_FLAG_READ_1_1_4 | \
+ FLASH_FLAG_READ_1_4_4 | \
+ FLASH_FLAG_WRITE_1_1_4)
+ { "w25q80", 0xef4014, 0, 64 * 1024, 16, W25Q_FLAG, 80, NULL },
+ { "w25q16", 0xef4015, 0, 64 * 1024, 32, W25Q_FLAG, 80, NULL },
+ { "w25q32", 0xef4016, 0, 64 * 1024, 64, W25Q_FLAG, 80, NULL },
+ { "w25q64", 0xef4017, 0, 64 * 1024, 128, W25Q_FLAG, 80, NULL },
+
+ /* Sentinel */
+ { NULL, 0x000000, 0, 0, 0, 0, 0, NULL },
+};
+
#endif /* ST_SPI_FSM_H */
--
1.8.3.2
More information about the linux-arm-kernel
mailing list