[PATCH v4 1/2] clk/zynq/clkc: Add 'fclk-enable' feature

[Soren Brinkmann]

In some use cases Zynq's FPGA clocks are used as static clock
generators for IP in the FPGA part of the SOC for which no Linux driver
exists and would control those clocks. To avoid automatic
gating of these clocks in such cases a new property - fclk-enable - is
added to the clock controller's DT description to accomodate such use
cases. It's value is a bitmask, where a set bit results in enabling
the corresponding FCLK through the clkc.

FPGA clocks are handled following the rules below:

If an FCLK is not enabled by bootloaders, that FCLK will be disabled in
Linux. Drivers can enable and control it through the CCF as usual.

If an FCLK is enabled by bootloaders AND the corresponding bit in the
'fclk-enable' DT property is set, that FCLK will be enabled by the clkc,
resulting in an off by one reference count for that clock. Ensuring it
will always be running.

Signed-off-by: Soren Brinkmann <soren.brinkmann at xilinx.com>
Acked-by: Michal Simek <michal.simek at xilinx.com>
---
v4:
 - replace bitwise with logical AND
v3:
 - documentation stated the default for fclk-enable is 0xf. This changed
   in v2 => remove that note
v2:
 - change default value for fclk-enable to '0'
---
 Documentation/devicetree/bindings/clock/zynq-7000.txt |  4 ++++
 drivers/clk/zynq/clkc.c                               | 18 +++++++++++++++---
 2 files changed, 19 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/clock/zynq-7000.txt b/Documentation/devicetree/bindings/clock/zynq-7000.txt
index d99af878f5d7..17b4a94916d6 100644
--- a/Documentation/devicetree/bindings/clock/zynq-7000.txt
+++ b/Documentation/devicetree/bindings/clock/zynq-7000.txt
@@ -22,6 +22,10 @@ Required properties:
 Optional properties:
  - clocks : as described in the clock bindings
  - clock-names : as described in the clock bindings
+ - fclk-enable : Bit mask to enable FCLKs statically at boot time.
+		 Bit [0..3] correspond to FCLK0..FCLK3. The corresponding
+		 FCLK will only be enabled if it is actually running at
+		 boot time.
 
 Clock inputs:
 The following strings are optional parameters to the 'clock-names' property in
diff --git a/drivers/clk/zynq/clkc.c b/drivers/clk/zynq/clkc.c
index 10772aa72e4e..09dd0173ea0a 100644
--- a/drivers/clk/zynq/clkc.c
+++ b/drivers/clk/zynq/clkc.c
@@ -102,9 +102,10 @@ static const char *swdt_ext_clk_input_names[] __initdata = {"swdt_ext_clk"};
 
 static void __init zynq_clk_register_fclk(enum zynq_clk fclk,
 		const char *clk_name, void __iomem *fclk_ctrl_reg,
-		const char **parents)
+		const char **parents, int enable)
 {
 	struct clk *clk;
+	u32 enable_reg;
 	char *mux_name;
 	char *div0_name;
 	char *div1_name;
@@ -147,6 +148,12 @@ static void __init zynq_clk_register_fclk(enum zynq_clk fclk,
 	clks[fclk] = clk_register_gate(NULL, clk_name,
 			div1_name, CLK_SET_RATE_PARENT, fclk_gate_reg,
 			0, CLK_GATE_SET_TO_DISABLE, fclk_gate_lock);
+	enable_reg = readl(fclk_gate_reg) & 1;
+	if (enable && !enable_reg) {
+		if (clk_prepare_enable(clks[fclk]))
+			pr_warn("%s: FCLK%u enable failed\n", __func__,
+					fclk - fclk0);
+	}
 	kfree(mux_name);
 	kfree(div0_name);
 	kfree(div1_name);
@@ -213,6 +220,7 @@ static void __init zynq_clk_setup(struct device_node *np)
 	int ret;
 	struct clk *clk;
 	char *clk_name;
+	unsigned int fclk_enable = 0;
 	const char *clk_output_name[clk_max];
 	const char *cpu_parents[4];
 	const char *periph_parents[4];
@@ -238,6 +246,8 @@ static void __init zynq_clk_setup(struct device_node *np)
 	periph_parents[2] = clk_output_name[armpll];
 	periph_parents[3] = clk_output_name[ddrpll];
 
+	of_property_read_u32(np, "fclk-enable", &fclk_enable);
+
 	/* ps_clk */
 	ret = of_property_read_u32(np, "ps-clk-frequency", &tmp);
 	if (ret) {
@@ -340,10 +350,12 @@ static void __init zynq_clk_setup(struct device_node *np)
 	clk_prepare_enable(clks[dci]);
 
 	/* Peripheral clocks */
-	for (i = fclk0; i <= fclk3; i++)
+	for (i = fclk0; i <= fclk3; i++) {
+		int enable = !!(fclk_enable & BIT(i - fclk0));
 		zynq_clk_register_fclk(i, clk_output_name[i],
 				SLCR_FPGA0_CLK_CTRL + 0x10 * (i - fclk0),
-				periph_parents);
+				periph_parents, enable);
+	}
 
 	zynq_clk_register_periph_clk(lqspi, 0, clk_output_name[lqspi], NULL,
 			SLCR_LQSPI_CLK_CTRL, periph_parents, 0);
-- 
1.8.4.4