[PATCH V6 2/3] ahci: imx: Pull out the clock enable/disable calls
Marek Vasut
marex at denx.de
Mon Nov 25 03:47:01 EST 2013
The same code for enabling and disabling SATA clock was found in multiple
places in the driver. Implement functions that enable/disable the SATA clock
and use them in such places instead of duplicating the code.
Signed-off-by: Marek Vasut <marex at denx.de>
Cc: Shawn Guo <shawn.guo at linaro.org>
Cc: Richard Zhu <r65037 at freescale.com>
Cc: Tejun Heo <tj at kernel.org>
Cc: Linux-IDE <linux-ide at vger.kernel.org>
---
drivers/ata/ahci_imx.c | 143 ++++++++++++++++++++++++++-----------------------
1 file changed, 75 insertions(+), 68 deletions(-)
V2: Move the OR sign from the begining of the line to the end of the line in
the regmap_update_bits() call.
V3: Move the PHY configuration programming out of the clock_enable function
and into the probe() function.
V4: Rebase on top of new 1/6 patch.
Remove clk_prepare_enable() being called twice in imx_sata_clock_enable()
since it was a rebase artifact.
V5: Pull out the usleep_range() into imx_sata_clock_enable() as well as a small
delay is needed after turning on the clock. Also rebase this on top of the
change in comment in 1/6 .
V6: Rebase this on top of the change in comment in 1/3 .
diff --git a/drivers/ata/ahci_imx.c b/drivers/ata/ahci_imx.c
index 3e23e99..6214411 100644
--- a/drivers/ata/ahci_imx.c
+++ b/drivers/ata/ahci_imx.c
@@ -47,6 +47,36 @@ static int ahci_imx_hotplug;
module_param_named(hotplug, ahci_imx_hotplug, int, 0644);
MODULE_PARM_DESC(hotplug, "AHCI IMX hot-plug support (0=Don't support, 1=support)");
+static int imx_sata_clock_enable(struct device *dev)
+{
+ struct imx_ahci_priv *imxpriv = dev_get_drvdata(dev->parent);
+ int ret;
+
+ ret = clk_prepare_enable(imxpriv->sata_ref_clk);
+ if (ret < 0) {
+ dev_err(dev, "prepare-enable sata_ref clock err:%d\n", ret);
+ return ret;
+ }
+
+ regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
+ IMX6Q_GPR13_SATA_MPLL_CLK_EN,
+ IMX6Q_GPR13_SATA_MPLL_CLK_EN);
+
+ usleep_range(1000, 2000);
+
+ return 0;
+}
+
+static void imx_sata_clock_disable(struct device *dev)
+{
+ struct imx_ahci_priv *imxpriv = dev_get_drvdata(dev->parent);
+
+ regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
+ IMX6Q_GPR13_SATA_MPLL_CLK_EN,
+ !IMX6Q_GPR13_SATA_MPLL_CLK_EN);
+ clk_disable_unprepare(imxpriv->sata_ref_clk);
+}
+
static void ahci_imx_error_handler(struct ata_port *ap)
{
u32 reg_val;
@@ -72,10 +102,7 @@ static void ahci_imx_error_handler(struct ata_port *ap)
*/
reg_val = readl(mmio + PORT_PHY_CTL);
writel(reg_val | PORT_PHY_CTL_PDDQ_LOC, mmio + PORT_PHY_CTL);
- regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
- IMX6Q_GPR13_SATA_MPLL_CLK_EN,
- !IMX6Q_GPR13_SATA_MPLL_CLK_EN);
- clk_disable_unprepare(imxpriv->sata_ref_clk);
+ imx_sata_clock_disable(ap->dev);
imxpriv->no_device = true;
}
@@ -97,46 +124,9 @@ static int imx6q_sata_init(struct device *dev, void __iomem *mmio)
unsigned int reg_val;
struct imx_ahci_priv *imxpriv = dev_get_drvdata(dev->parent);
- imxpriv->gpr =
- syscon_regmap_lookup_by_compatible("fsl,imx6q-iomuxc-gpr");
- if (IS_ERR(imxpriv->gpr)) {
- dev_err(dev, "failed to find fsl,imx6q-iomux-gpr regmap\n");
- return PTR_ERR(imxpriv->gpr);
- }
-
- ret = clk_prepare_enable(imxpriv->sata_ref_clk);
- if (ret < 0) {
- dev_err(dev, "prepare-enable sata_ref clock err:%d\n", ret);
+ ret = imx_sata_clock_enable(dev);
+ if (ret < 0)
return ret;
- }
-
- /*
- * set PHY Paremeters, two steps to configure the GPR13,
- * one write for rest of parameters, mask of first write
- * is 0x07ffffff, and the other one write for setting
- * the mpll_clk_en.
- */
- regmap_update_bits(imxpriv->gpr, 0x34, IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK
- | IMX6Q_GPR13_SATA_RX_LOS_LVL_MASK
- | IMX6Q_GPR13_SATA_RX_DPLL_MODE_MASK
- | IMX6Q_GPR13_SATA_SPD_MODE_MASK
- | IMX6Q_GPR13_SATA_MPLL_SS_EN
- | IMX6Q_GPR13_SATA_TX_ATTEN_MASK
- | IMX6Q_GPR13_SATA_TX_BOOST_MASK
- | IMX6Q_GPR13_SATA_TX_LVL_MASK
- | IMX6Q_GPR13_SATA_MPLL_CLK_EN
- | IMX6Q_GPR13_SATA_TX_EDGE_RATE
- , IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB
- | IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M
- | IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F
- | IMX6Q_GPR13_SATA_SPD_MODE_3P0G
- | IMX6Q_GPR13_SATA_MPLL_SS_EN
- | IMX6Q_GPR13_SATA_TX_ATTEN_9_16
- | IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB
- | IMX6Q_GPR13_SATA_TX_LVL_1_025_V);
- regmap_update_bits(imxpriv->gpr, 0x34, IMX6Q_GPR13_SATA_MPLL_CLK_EN,
- IMX6Q_GPR13_SATA_MPLL_CLK_EN);
- usleep_range(100, 200);
/*
* Configure the HWINIT bits of the HOST_CAP and HOST_PORTS_IMPL,
@@ -164,11 +154,7 @@ static int imx6q_sata_init(struct device *dev, void __iomem *mmio)
static void imx6q_sata_exit(struct device *dev)
{
- struct imx_ahci_priv *imxpriv = dev_get_drvdata(dev->parent);
-
- regmap_update_bits(imxpriv->gpr, 0x34, IMX6Q_GPR13_SATA_MPLL_CLK_EN,
- !IMX6Q_GPR13_SATA_MPLL_CLK_EN);
- clk_disable_unprepare(imxpriv->sata_ref_clk);
+ imx_sata_clock_disable(dev);
}
static int imx_ahci_suspend(struct device *dev)
@@ -179,12 +165,8 @@ static int imx_ahci_suspend(struct device *dev)
* If no_device is set, The CLKs had been gated off in the
* initialization so don't do it again here.
*/
- if (!imxpriv->no_device) {
- regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
- IMX6Q_GPR13_SATA_MPLL_CLK_EN,
- !IMX6Q_GPR13_SATA_MPLL_CLK_EN);
- clk_disable_unprepare(imxpriv->sata_ref_clk);
- }
+ if (!imxpriv->no_device)
+ imx_sata_clock_disable(dev);
return 0;
}
@@ -192,22 +174,12 @@ static int imx_ahci_suspend(struct device *dev)
static int imx_ahci_resume(struct device *dev)
{
struct imx_ahci_priv *imxpriv = dev_get_drvdata(dev->parent);
- int ret;
+ int ret = 0;
- if (!imxpriv->no_device) {
- ret = clk_prepare_enable(imxpriv->sata_ref_clk);
- if (ret < 0) {
- dev_err(dev, "pre-enable sata_ref clock err:%d\n", ret);
- return ret;
- }
-
- regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
- IMX6Q_GPR13_SATA_MPLL_CLK_EN,
- IMX6Q_GPR13_SATA_MPLL_CLK_EN);
- usleep_range(1000, 2000);
- }
+ if (!imxpriv->no_device)
+ ret = imx_sata_clock_enable(dev);
- return 0;
+ return ret;
}
static struct ahci_platform_data imx6q_sata_pdata = {
@@ -290,6 +262,41 @@ static int imx_ahci_probe(struct platform_device *pdev)
ahci_dev->dma_mask = &ahci_dev->coherent_dma_mask;
ahci_dev->of_node = dev->of_node;
+ imxpriv->gpr =
+ syscon_regmap_lookup_by_compatible("fsl,imx6q-iomuxc-gpr");
+
+ if (IS_ERR(imxpriv->gpr)) {
+ dev_err(dev, "failed to find fsl,imx6q-iomux-gpr regmap\n");
+ ret = PTR_ERR(imxpriv->gpr);
+ goto err_out;
+ }
+
+ /*
+ * Set PHY Paremeters, two steps to configure the GPR13,
+ * one write for rest of parameters, mask of first write
+ * is 0x07ffffff, and the other one write for setting
+ * the mpll_clk_en happens in imx_sata_clock_enable().
+ */
+ regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
+ IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK |
+ IMX6Q_GPR13_SATA_RX_LOS_LVL_MASK |
+ IMX6Q_GPR13_SATA_RX_DPLL_MODE_MASK |
+ IMX6Q_GPR13_SATA_SPD_MODE_MASK |
+ IMX6Q_GPR13_SATA_MPLL_SS_EN |
+ IMX6Q_GPR13_SATA_TX_ATTEN_MASK |
+ IMX6Q_GPR13_SATA_TX_BOOST_MASK |
+ IMX6Q_GPR13_SATA_TX_LVL_MASK |
+ IMX6Q_GPR13_SATA_MPLL_CLK_EN |
+ IMX6Q_GPR13_SATA_TX_EDGE_RATE,
+ IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB |
+ IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M |
+ IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F |
+ IMX6Q_GPR13_SATA_SPD_MODE_3P0G |
+ IMX6Q_GPR13_SATA_MPLL_SS_EN |
+ IMX6Q_GPR13_SATA_TX_ATTEN_9_16 |
+ IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB |
+ IMX6Q_GPR13_SATA_TX_LVL_1_025_V);
+
ret = platform_device_add_resources(ahci_pdev, res, 2);
if (ret)
goto err_out;
--
1.8.4.3
More information about the linux-arm-kernel
mailing list