[PATCH v3 09/10] ARM: dts: omap3-beagle-xm: Add USB Host support

[Nishanth Menon]

On 09/24/2013 03:53 AM, Roger Quadros wrote:
> Provide RESET GPIO and Power regulator for the USB PHY,
> the USB Host port mode and the PHY device for the controller.
> Also provide pin multiplexer information for USB host pins.
> 
> We also relocate omap3_pmx_core pin definations so that they
> are close to omap3_pmx_wkup pin definations.
> 
> Signed-off-by: Roger Quadros <rogerq at ti.com>
> ---

just using this thread, but a question ->

I am kernel * master                                   dec8e46 Merge
tag 'arc-v3.13-rc1-part2' of
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc

and I see that VAUX2 which supplies USB_1V8[1] is not enabled -> I did
a quick patch and it did seem to work (Usb keyboard, networking, mouse
etc on my ehci ports seems to come up good) - any suggestions how we'd
like to handle this?

--- a/arch/arm/boot/dts/omap3-beagle-xm.dts
+++ b/arch/arm/boot/dts/omap3-beagle-xm.dts
@@ -169,6 +169,14 @@
        bus-width = <8>;
 };

+&vaux2 {
+       regulator-name = "HubPower";
+       regulator-min-microvolt = <1800000>;
+       regulator-max-microvolt = <1800000>;
+       regulator-always-on;
+};
+
+

[1]
https://github.com/CircuitCo/BeagleBoard-xM-RevC/blob/master/BeagleBoard-xM_revC_SCH.pdf?raw=true

>  arch/arm/boot/dts/omap3-beagle-xm.dts |   65 ++++++++++++++++++++++++++++-----
>  1 files changed, 56 insertions(+), 9 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts
> index afdb164..b081f5a 100644
> --- a/arch/arm/boot/dts/omap3-beagle-xm.dts
> +++ b/arch/arm/boot/dts/omap3-beagle-xm.dts
> @@ -69,6 +69,23 @@
>  		};
>  
>  	};
> +
> +	/* HS USB Port 2 Power */
> +	hsusb2_power: hsusb2_power_reg {
> +		compatible = "regulator-fixed";
> +		regulator-name = "hsusb2_vbus";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&twl_gpio 18 0>;	/* GPIO LEDA */
> +		startup-delay-us = <70000>;
> +	};
> +
> +	/* HS USB Host PHY on PORT 2 */
> +	hsusb2_phy: hsusb2_phy {
> +		compatible = "usb-nop-xceiv";
> +		reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; /* gpio_147 */
> +		vcc-supply = <&hsusb2_power>;
> +	};
>  };
>  
>  &omap3_pmx_wkup {
> @@ -79,6 +96,37 @@
>  	};
>  };
>  
> +&omap3_pmx_core {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <
> +			&hsusbb2_pins
> +	>;
> +
> +	uart3_pins: pinmux_uart3_pins {
> +		pinctrl-single,pins = <
> +			0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
> +			0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */
> +		>;
> +	};
> +
> +	hsusbb2_pins: pinmux_hsusbb2_pins {
> +		pinctrl-single,pins = <
> +			0x5c0 (PIN_OUTPUT | MUX_MODE3)		/* etk_d10.hsusb2_clk */
> +			0x5c2 (PIN_OUTPUT | MUX_MODE3)		/* etk_d11.hsusb2_stp */
> +			0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d12.hsusb2_dir */
> +			0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d13.hsusb2_nxt */
> +			0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d14.hsusb2_data0 */
> +			0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d15.hsusb2_data1 */
> +			0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi1_cs3.hsusb2_data2 */
> +			0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_clk.hsusb2_data7 */
> +			0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_simo.hsusb2_data4 */
> +			0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_somi.hsusb2_data5 */
> +			0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs0.hsusb2_data6 */
> +			0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs1.hsusb2_data3 */
> +		>;
> +	};
> +};
> +
>  &i2c1 {
>  	clock-frequency = <2600000>;
>  
> @@ -148,15 +196,6 @@
>  	power = <50>;
>  };
>  
> -&omap3_pmx_core {
> -	uart3_pins: pinmux_uart3_pins {
> -		pinctrl-single,pins = <
> -			0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
> -			0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */
> -		>;
> -	};
> -};
> -
>  &uart3 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&uart3_pins>;
> @@ -166,3 +205,11 @@
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&gpio1_pins>;
>  };
> +
> +&usbhshost {
> +	port2-mode = "ehci-phy";
> +};
> +
> +&usbhsehci {
> +	phys = <0 &hsusb2_phy>;
> +};
> 


-- 
Regards,
Nishanth Menon