[PATCHv2] ARM: mvebu: Add Netgear ReadyNAS 2120 board
Arnaud Ebalard
arno at natisbad.org
Mon Nov 11 15:01:08 EST 2013
All hardware parts of the (mv78230 Armada XP based) NETGEAR ReadyNAS
2120 are supported by mainline kernel (USB 3.0 and eSATA rear ports,
USB 2.0 front port, Gigabit controller and PHYs for the two rear ports,
serial port, LEDs, Buttons, 88SE9170 SATA controllers, three G762 fan
controllers, G751 temperature sensor) except for:
- the Intersil ISL12057 I2C RTC Chip,
- the Armada NAND controller.
Support for both of those is currently work in progress and does not
prevent boot.
Signed-off-by: Arnaud Ebalard <arno at natisbad.org>
---
Hi,
Initial message:
This one is intended for v3.14. This depends on the recent fix I pushed
for mv78230 PCIe and also on a small patch Guenter Roeck just accepted
to have lm75 driver support GMT G751 Temperature sensor (see
https://lkml.org/lkml/2013/11/9/273).
Regarding the SATA presence and power pin definitions under pinctrl
node if you wonder, I thought it would not harm to have them for
reference even though they are currently not used. FWIW, I am currently
looking if a GPIO regulator can make any use of those.
Changes since v1:
After Andrew's comment:
- Added comment about G751 function
After Sebastian's comments:
- Changed clock frequency for a clock provider for serial line
- Added compatible string for PHY (marvell,mv88e1318s)
- Removed useless properties in clocks and gpio_keys nodes
- Made G762 clock node name unique by including g762 in it
- Changed values for macros for GPIO voltage level
- Removed comments after GPIOs
- Changed buttons and button pins names
After Jason's comment:
- Changed values for macros for input keys, removed comments
After more documenation reading:
- changed i2c compatible string to marvell,mv78230-i2c
Comments welcome,
Cheers,
a+
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/armada-xp-netgear-rn2120.dts | 288 +++++++++++++++++++++++++
2 files changed, 289 insertions(+)
create mode 100644 arch/arm/boot/dts/armada-xp-netgear-rn2120.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 802720e..c6dd4de 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -112,6 +112,7 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-370-db.dtb \
armada-xp-axpwifiap.dtb \
armada-xp-db.dtb \
armada-xp-gp.dtb \
+ armada-xp-netgear-rn2120.dtb \
armada-xp-openblocks-ax3-4.dtb
dtb-$(CONFIG_ARCH_MXC) += \
imx25-karo-tx25.dtb \
diff --git a/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts b/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts
new file mode 100644
index 0000000..ba1e0de
--- /dev/null
+++ b/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts
@@ -0,0 +1,288 @@
+/*
+ * Device Tree file for NETGEAR ReadyNAS 2120
+ *
+ * Copyright (C) 2013, Arnaud EBALARD <arno at natisbad.org>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+/dts-v1/;
+
+#include "armada-xp-mv78230.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "NETGEAR ReadyNAS 2120";
+ compatible = "netgear,readynas-2120", "marvell,armadaxp-mv78230", "marvell,armadaxp", "marvell,armada-370-xp";
+
+ chosen {
+ bootargs = "console=ttyS0,115200 earlyprintk";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x00000000 0 0x80000000>; /* 2GB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>;
+
+ pcie-controller {
+ status = "okay";
+
+ /* Connected to first Marvell 88SE9170 SATA controller */
+ pcie at 1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+
+ /* Connected to second Marvell 88SE9170 SATA controller */
+ pcie at 2,0 {
+ /* Port 0, Lane 1 */
+ status = "okay";
+ };
+
+ /* Connected to Fresco Logic FL1009 USB 3.0 controller */
+ pcie at 5,0 {
+ /* Port 1, Lane 0 */
+ status = "okay";
+ };
+ };
+
+ internal-regs {
+ pinctrl {
+ poweroff: poweroff {
+ marvell,pins = "mpp42";
+ marvell,function = "gpio";
+ };
+
+ power_button_pin: power-button-pin {
+ marvell,pins = "mpp27";
+ marvell,function = "gpio";
+ };
+
+ reset_button_pin: reset-button-pin {
+ marvell,pins = "mpp41";
+ marvell,function = "gpio";
+ };
+
+ sata1_led_pin: sata1-led-pin {
+ marvell,pins = "mpp31";
+ marvell,function = "gpio";
+ };
+
+ sata2_led_pin: sata2-led-pin {
+ marvell,pins = "mpp40";
+ marvell,function = "gpio";
+ };
+
+ sata3_led_pin: sata3-led-pin {
+ marvell,pins = "mpp44";
+ marvell,function = "gpio";
+ };
+
+ sata4_led_pin: sata4-led-pin {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+
+ sata1_power_pin: sata1-power-pin {
+ marvell,pins = "mpp24";
+ marvell,function = "gpio";
+ };
+
+ sata2_power_pin: sata2-power-pin {
+ marvell,pins = "mpp25";
+ marvell,function = "gpio";
+ };
+
+ sata3_power_pin: sata3-power-pin {
+ marvell,pins = "mpp26";
+ marvell,function = "gpio";
+ };
+
+ sata4_power_pin: sata4-power-pin {
+ marvell,pins = "mpp28";
+ marvell,function = "gpio";
+ };
+
+ sata1_pres_pin: sata1-pres-pin {
+ marvell,pins = "mpp32";
+ marvell,function = "gpio";
+ };
+
+ sata2_pres_pin: sata2-pres-pin {
+ marvell,pins = "mpp33";
+ marvell,function = "gpio";
+ };
+
+ sata3_pres_pin: sata3-pres-pin {
+ marvell,pins = "mpp34";
+ marvell,function = "gpio";
+ };
+
+ sata4_pres_pin: sata4-pres-pin {
+ marvell,pins = "mpp35";
+ marvell,function = "gpio";
+ };
+
+ err_led_pin: err-led-pin {
+ marvell,pins = "mpp45";
+ marvell,function = "gpio";
+ };
+ };
+
+ serial at 12000 {
+ clocks = <&coreclk 0>;
+ status = "okay";
+ };
+
+ mdio {
+ phy0: ethernet-phy at 0 {
+ compatible = "marvell,88e1318s";
+ reg = <0>;
+ };
+
+ phy1: ethernet-phy at 1 {
+ compatible = "marvell,88e1318s";
+ reg = <1>;
+ };
+ };
+
+ ethernet at 70000 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+ };
+
+ ethernet at 74000 {
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "rgmii-id";
+ };
+
+ /* Front USB 2.0 port */
+ usb at 50000 {
+ status = "okay";
+ };
+
+ i2c at 11000 {
+ compatible = "marvell,mv78230-i2c";
+ clock-frequency = <400000>;
+ status = "okay";
+
+ /* Controller for rear fan #1 of 3 (Protechnic
+ * MGT4012XB-O20, 8000RPM) near eSATA port */
+ g762_fan1: g762 at 3e {
+ compatible = "gmt,g762";
+ reg = <0x3e>;
+ clocks = <&g762_clk>; /* input clock */
+ fan_gear_mode = <0>;
+ fan_startv = <1>;
+ pwm_polarity = <0>;
+ };
+
+ /* Controller for rear (center) fan #2 of 3 */
+ g762_fan2: g762 at 48 {
+ compatible = "gmt,g762";
+ reg = <0x48>;
+ clocks = <&g762_clk>; /* input clock */
+ fan_gear_mode = <0>;
+ fan_startv = <1>;
+ pwm_polarity = <0>;
+ };
+
+ /* Controller for rear fan #3 of 3 */
+ g762_fan3: g762 at 49 {
+ compatible = "gmt,g762";
+ reg = <0x49>;
+ clocks = <&g762_clk>; /* input clock */
+ fan_gear_mode = <0>;
+ fan_startv = <1>;
+ pwm_polarity = <0>;
+ };
+
+ /* Temperature sensor */
+ g751: g751 at 4c {
+ compatible = "gmt,g751";
+ reg = <0x4c>;
+ };
+ };
+ };
+ };
+
+ clocks {
+ g762_clk: g762_oscillator {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ };
+ };
+
+ gpio_leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&sata1_led_pin &sata2_led_pin &err_led_pin
+ &sata3_led_pin &sata4_led_pin>;
+ pinctrl-names = "default";
+
+ red_sata1_led {
+ label = "rn2120:red:sata1";
+ gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ red_sata2_led {
+ label = "rn2120:red:sata2";
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ red_sata3_led {
+ label = "rn2120:red:sata3";
+ gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ red_sata4_led {
+ label = "rn2120:red:sata4";
+ gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ red_err_led {
+ label = "rn2120:red:err";
+ gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&power_button_pin &reset_button_pin>;
+ pinctrl-names = "default";
+
+ power_button {
+ label = "Power Button";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>;
+ };
+
+ reset_button {
+ label = "Reset Button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio_poweroff {
+ compatible = "gpio-poweroff";
+ pinctrl-0 = <&poweroff>;
+ pinctrl-names = "default";
+ gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+ };
+};
--
1.8.4.rc3
More information about the linux-arm-kernel
mailing list