[PATCH] ARM: vt8500: add defconfig

[Tony Prisk]

On 10/11/13 17:24, Olof Johansson wrote:
> Add a single-vendor config for vt8500. We can't enable WM8750 in
> multi_v7_defconfig since it's a v6-based device, but it's still valuable
> to have an in-tree defconfig that is suitable for the hardware.
>
> This is based on multi_v7_defconfig and can be tweaked over time. It
> gets us off the ground for now.
>
> Booted on an APC8750 with USB rootfs.
>
> Signed-off-by: Olof Johansson <olof at lixom.net>
> ---
>
> Tony,
>
>
> I'll apply this to a suitable arm-soc branch sometime during the merge window,
> since it doesn't affect existing systems. A review/ack would be appreciated!
>
>
> -Olof
>
>   arch/arm/configs/vt8500_defconfig |   88 +++++++++++++++++++++++++++++++++++++
>   1 file changed, 88 insertions(+)
>   create mode 100644 arch/arm/configs/vt8500_defconfig
>
> diff --git a/arch/arm/configs/vt8500_defconfig b/arch/arm/configs/vt8500_defconfig
> new file mode 100644
> index 0000000..6fd3717
> --- /dev/null
> +++ b/arch/arm/configs/vt8500_defconfig
> @@ -0,0 +1,88 @@
> +CONFIG_IRQ_DOMAIN_DEBUG=y
> +CONFIG_NO_HZ=y
> +CONFIG_HIGH_RES_TIMERS=y
> +CONFIG_BLK_DEV_INITRD=y
> +CONFIG_ARCH_MULTI_V6=y
> +CONFIG_ARCH_WM8750=y
> +CONFIG_ARCH_WM8850=y
> +CONFIG_ARM_ERRATA_720789=y
> +CONFIG_ARM_ERRATA_754322=y
> +CONFIG_ARM_ERRATA_775420=y
> +CONFIG_HAVE_ARM_ARCH_TIMER=y
> +CONFIG_AEABI=y
> +CONFIG_HIGHMEM=y
> +CONFIG_HIGHPTE=y
> +CONFIG_ARM_APPENDED_DTB=y
> +CONFIG_ARM_ATAG_DTB_COMPAT=y
> +CONFIG_VFP=y
> +CONFIG_NEON=y
> +CONFIG_PM_RUNTIME=y
> +CONFIG_NET=y
> +CONFIG_UNIX=y
> +CONFIG_INET=y
> +CONFIG_IP_PNP=y
> +CONFIG_IP_PNP_DHCP=y
> +CONFIG_DEVTMPFS=y
> +CONFIG_DEVTMPFS_MOUNT=y
> +CONFIG_PROC_DEVICETREE=y
> +CONFIG_EEPROM_93CX6=y
> +CONFIG_SCSI=y
> +CONFIG_BLK_DEV_SD=y
> +CONFIG_NETDEVICES=y
> +# CONFIG_NET_CADENCE is not set
> +# CONFIG_NET_VENDOR_BROADCOM is not set
> +# CONFIG_NET_VENDOR_CIRRUS is not set
> +# CONFIG_NET_VENDOR_FARADAY is not set
> +# CONFIG_NET_VENDOR_INTEL is not set
> +# CONFIG_NET_VENDOR_MARVELL is not set
> +# CONFIG_NET_VENDOR_MICREL is not set
> +# CONFIG_NET_VENDOR_NATSEMI is not set
> +# CONFIG_NET_VENDOR_SEEQ is not set
> +# CONFIG_NET_VENDOR_SMSC is not set
> +# CONFIG_NET_VENDOR_STMICRO is not set
> +CONFIG_VIA_VELOCITY=y
> +# CONFIG_NET_VENDOR_WIZNET is not set
> +CONFIG_PHYLIB=y
> +CONFIG_INPUT_MATRIXKMAP=y
> +CONFIG_SERIAL_VT8500=y
> +CONFIG_SERIAL_VT8500_CONSOLE=y
> +CONFIG_PINCTRL_SINGLE=y
> +CONFIG_PINCTRL_WM8750=y
> +CONFIG_GPIO_GENERIC_PLATFORM=y
> +CONFIG_POWER_SUPPLY=y
> +CONFIG_POWER_RESET=y
> +CONFIG_MFD_SYSCON=y
> +CONFIG_REGULATOR=y
> +CONFIG_REGULATOR_FIXED_VOLTAGE=y
> +CONFIG_REGULATOR_GPIO=y
> +CONFIG_USB=y
> +CONFIG_USB_EHCI_HCD=y
> +CONFIG_USB_EHCI_HCD_PLATFORM=y
> +CONFIG_USB_UHCI_HCD=y
> +CONFIG_USB_STORAGE=y
> +CONFIG_NOP_USB_XCEIV=y
> +CONFIG_USB_GPIO_VBUS=y
> +CONFIG_USB_ULPI=y
> +CONFIG_MMC=y
> +CONFIG_MMC_DEBUG=y
> +CONFIG_NEW_LEDS=y
> +CONFIG_LEDS_CLASS=y
> +CONFIG_LEDS_TRIGGERS=y
> +CONFIG_RTC_CLASS=y
> +CONFIG_RTC_DRV_VT8500=y
> +CONFIG_DMADEVICES=y
> +CONFIG_COMMON_CLK_DEBUG=y
> +# CONFIG_IOMMU_SUPPORT is not set
> +CONFIG_PWM=y
> +CONFIG_PWM_VT8500=y
> +CONFIG_RESET_CONTROLLER=y
> +CONFIG_GENERIC_PHY=y
> +CONFIG_EXT4_FS=y
> +CONFIG_TMPFS=y
> +CONFIG_NFS_FS=y
> +CONFIG_NFS_V3_ACL=y
> +CONFIG_NFS_V4=y
> +CONFIG_ROOT_NFS=y
> +CONFIG_PRINTK_TIME=y
> +CONFIG_DEBUG_KERNEL=y
> +CONFIG_LOCKUP_DETECTOR=y

I notice you left out the I2C driver and the MMC driver - given you 
had/have problems with them this is understandable. They can be sorted 
out later.

My main concern is that this file is named 'vt8500_defconfig', but it 
won't be able to cover all of the VT8500 'family'.
The earlier models (vt8500/wm8505) are ARM9, the WM8650 was ARM11, and 
then we got to the WM8750 that you are targetting (ARMv6) and finally 
the ARMv7 stuff (WM8850/WM8950).
I'm not particularly fussed about it (it's fine as is), but if you think 
of a better filename to fit the situation I wouldn't complain :)

Reviewed-by: Tony Prisk <linux at prisktech.co.nz>

Regards
Tony P