[PATCH] ARM: mvebu: Add Netgear ReadyNAS 2120 board
Arnaud Ebalard
arno at natisbad.org
Sat Nov 9 16:26:12 EST 2013
Hi,
Andrew Lunn <andrew at lunn.ch> writes:
> On Sat, Nov 09, 2013 at 09:27:32PM +0100, Arnaud Ebalard wrote:
>>
>> All hardware parts of the (mv78230 Armada XP based) NETGEAR ReadyNAS
>> 2120 are supported by mainline kernel (USB 3.0 and eSATA rear ports,
>> USB 2.0 front port, Gigabit controller and PHYs for the two rear ports,
>> serial port, LEDs, Buttons, 88SE9170 SATA controllers, three G762 fan
>> controllers, G751 temperature sensor) except for:
>
>> + i2c at 11000 {
>> + compatible = "marvell,mv64xxx-i2c";
>> + clock-frequency = <400000>;
>> + status = "okay";
>> +
>> + /* Rear fan #1 of 3 (Protechnic MGT4012XB-O20,
>> + * 8000RPM) near eSATA port */
>> + g762_fan1: g762 at 3e {
>> + compatible = "gmt,g762";
>> + reg = <0x3e>;
>> + clocks = <&g762_clk>; /* input clock */
>> + fan_gear_mode = <0>;
>> + fan_startv = <1>;
>> + pwm_polarity = <0>;
>> + };
>> +
>> + /* Rear fan #2 of 3 at the center */
>> + g762_fan2: g762 at 48 {
>> + compatible = "gmt,g762";
>> + reg = <0x48>;
>> + clocks = <&g762_clk>; /* input clock */
>> + fan_gear_mode = <0>;
>> + fan_startv = <1>;
>> + pwm_polarity = <0>;
>> + };
>> +
>> + /* Rear fan #3 of 3 */
>> + g762_fan3: g762 at 49 {
>> + compatible = "gmt,g762";
>> + reg = <0x49>;
>> + clocks = <&g762_clk>; /* input clock */
>> + fan_gear_mode = <0>;
>> + fan_startv = <1>;
>> + pwm_polarity = <0>;
>> + };
>> +
>> + g751: g751 at 4c {
>> + compatible = "gmt,g751";
>> + reg = <0x4c>;
>> + };
>
> Hi Arnaud
>
> Looks good to me. However, if for some reason you need to respin, it
> would be nice to add a comment about what the g751 is. All the other
> i2c devices you say what they are. No need to respin just because of
> this.
I'll keep that in mind. Thanks.
GMT G751 is an I2C temperature sensor and thermal watchdog chip. It is
basically a clone of National Semiconductor LM75 chip:
root at thin:/sys# sensors
g762-i2c-0-3e
Adapter: mv64xxx_i2c adapter
fan1: 5461 RPM (div = 1)
g762-i2c-0-48
Adapter: mv64xxx_i2c adapter
fan1: 5461 RPM (div = 1)
g762-i2c-0-49
Adapter: mv64xxx_i2c adapter
fan1: 5461 RPM (div = 1)
g751-i2c-0-4c
Adapter: mv64xxx_i2c adapter
temp1: +30.5°C (high = +80.0°C, hyst = +75.0°C)
armada_thermal-virtual-0
Adapter: Virtual device
temp1: +34.2°C
Cheers,
a+
More information about the linux-arm-kernel
mailing list