[PATCH v2] ARM/serial: at91: switch atmel serial to use gpiolib

Nicolas Ferre nicolas.ferre at atmel.com
Wed Nov 6 05:06:03 EST 2013


On 06/11/2013 10:25, Linus Walleij :
> This passes the errata fix using a GPIO to control the RTS pin
> on one of the AT91 chips to use gpiolib instead of the
> AT91-specific interfaces. Also remove the reliance on
> compile-time #defines and the cpu_* check and rely on the
> platform passing down the proper GPIO pin through platform
> data.
>
> This is a prerequisite for getting rid of the local GPIO
> implementation in the AT91 platform and move toward
> multiplatform.
>
> The patch also adds device tree support for getting the
> RTS GPIO pin from the device tree on DT boot paths.
>
> Signed-off-by: Nicolas Ferre <nicolas.ferre at atmel.com>
> Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
> ---
> ChangeLog v1->v2:
> - Skip check for UART base address from leftover hack,
>    if we have an RTS GPIO we just use it.
> - Set default error value on GPIO pin to -EINVAL
> - Fold in a device tree support patch from Nicolas Ferre

Thanks for having done this Linus!

Greg, this patch is ready now and it supersedes the one you acknowledged 
earlier ([PATCH 1/4] ARM/serial: at91: move machine quirk into machine).

Best regards,


> ---
>   .../devicetree/bindings/serial/atmel-usart.txt     |  3 ++
>   arch/arm/mach-at91/at91rm9200_devices.c            |  1 +
>   drivers/tty/serial/atmel_serial.c                  | 55 +++++++++++++++-------
>   include/linux/platform_data/atmel.h                |  1 +
>   4 files changed, 42 insertions(+), 18 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/serial/atmel-usart.txt b/Documentation/devicetree/bindings/serial/atmel-usart.txt
> index 2191dcb9f1da..3adc61c2e4ca 100644
> --- a/Documentation/devicetree/bindings/serial/atmel-usart.txt
> +++ b/Documentation/devicetree/bindings/serial/atmel-usart.txt
> @@ -10,6 +10,8 @@ Required properties:
>   Optional properties:
>   - atmel,use-dma-rx: use of PDC or DMA for receiving data
>   - atmel,use-dma-tx: use of PDC or DMA for transmitting data
> +- rts-gpios: specify a GPIO for RTS line. It will use specified PIO instead of the peripheral
> +  function pin for the USART RTS feature. If unsure, don't specify this property.
>   - add dma bindings for dma transfer:
>   	- dmas: DMA specifier, consisting of a phandle to DMA controller node,
>   		memory peripheral interface and USART DMA channel ID, FIFO configuration.
> @@ -28,6 +30,7 @@ Example:
>   		interrupts = <7>;
>   		atmel,use-dma-rx;
>   		atmel,use-dma-tx;
> +		rts-gpios = <&pioD 15 0>;
>   	};
>
>   - use DMA:
> diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c
> index c721e9b08066..51d4c08962f6 100644
> --- a/arch/arm/mach-at91/at91rm9200_devices.c
> +++ b/arch/arm/mach-at91/at91rm9200_devices.c
> @@ -961,6 +961,7 @@ static struct resource uart0_resources[] = {
>   static struct atmel_uart_data uart0_data = {
>   	.use_dma_tx	= 1,
>   	.use_dma_rx	= 1,
> +	.rts_gpio	= AT91_PIN_PA21,
>   };
>
>   static u64 uart0_dmamask = DMA_BIT_MASK(32);
> diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
> index d067285a2d20..e31f3319be64 100644
> --- a/drivers/tty/serial/atmel_serial.c
> +++ b/drivers/tty/serial/atmel_serial.c
> @@ -35,21 +35,18 @@
>   #include <linux/platform_device.h>
>   #include <linux/of.h>
>   #include <linux/of_device.h>
> +#include <linux/of_gpio.h>
>   #include <linux/dma-mapping.h>
>   #include <linux/atmel_pdc.h>
>   #include <linux/atmel_serial.h>
>   #include <linux/uaccess.h>
>   #include <linux/platform_data/atmel.h>
>   #include <linux/timer.h>
> +#include <linux/gpio.h>
>
>   #include <asm/io.h>
>   #include <asm/ioctls.h>
>
> -#ifdef CONFIG_ARM
> -#include <mach/cpu.h>
> -#include <asm/gpio.h>
> -#endif
> -
>   #define PDC_BUFFER_SIZE		512
>   /* Revisit: We should calculate this based on the actual port settings */
>   #define PDC_RX_TIMEOUT		(3 * 10)		/* 3 bytes */
> @@ -167,6 +164,7 @@ struct atmel_uart_port {
>   	struct circ_buf		rx_ring;
>
>   	struct serial_rs485	rs485;		/* rs485 settings */
> +	int			rts_gpio;	/* optional RTS GPIO */
>   	unsigned int		tx_done_mask;
>   	bool			is_usart;	/* usart or uart */
>   	struct timer_list	uart_timer;	/* uart timer */
> @@ -300,20 +298,16 @@ static void atmel_set_mctrl(struct uart_port *port, u_int mctrl)
>   	unsigned int mode;
>   	struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
>
> -#ifdef CONFIG_ARCH_AT91RM9200
> -	if (cpu_is_at91rm9200()) {
> -		/*
> -		 * AT91RM9200 Errata #39: RTS0 is not internally connected
> -		 * to PA21. We need to drive the pin manually.
> -		 */
> -		if (port->mapbase == AT91RM9200_BASE_US0) {
> -			if (mctrl & TIOCM_RTS)
> -				at91_set_gpio_value(AT91_PIN_PA21, 0);
> -			else
> -				at91_set_gpio_value(AT91_PIN_PA21, 1);
> -		}
> +	/*
> +	 * AT91RM9200 Errata #39: RTS0 is not internally connected
> +	 * to PA21. We need to drive the pin as a GPIO.
> +	 */
> +	if (gpio_is_valid(atmel_port->rts_gpio)) {
> +		if (mctrl & TIOCM_RTS)
> +			gpio_set_value(atmel_port->rts_gpio, 0);
> +		else
> +			gpio_set_value(atmel_port->rts_gpio, 1);
>   	}
> -#endif
>
>   	if (mctrl & TIOCM_RTS)
>   		control |= ATMEL_US_RTSEN;
> @@ -2365,6 +2359,31 @@ static int atmel_serial_probe(struct platform_device *pdev)
>   	port = &atmel_ports[ret];
>   	port->backup_imr = 0;
>   	port->uart.line = ret;
> +	port->rts_gpio = -EINVAL; /* Invalid, zero could be valid */
> +	/*
> +	 * In theory the GPIO pin controlling RTS could be zero and
> +	 * this would be an improper check, but we know that the only
> +	 * existing case is != 0 and it's nice to use the zero-initialized
> +	 * structs to indicate "no RTS GPIO" instead of open-coding some
> +	 * invalid value everywhere.
> +	 */
> +	if (pdata && pdata->rts_gpio > 0)
> +		port->rts_gpio = pdata->rts_gpio;
> +	else if (np)
> +		port->rts_gpio = of_get_named_gpio(np, "rts-gpios", 0);
> +
> +	if (gpio_is_valid(port->rts_gpio)) {
> +		ret = devm_gpio_request(&pdev->dev, port->rts_gpio, "RTS");
> +		if (ret) {
> +			dev_err(&pdev->dev, "error requesting RTS GPIO\n");
> +			goto err;
> +		}
> +		ret = gpio_direction_output(port->rts_gpio, 0);
> +		if (ret) {
> +			dev_err(&pdev->dev, "error setting up RTS GPIO\n");
> +			goto err;
> +		}
> +	}
>
>   	ret = atmel_init_port(port, pdev);
>   	if (ret)
> diff --git a/include/linux/platform_data/atmel.h b/include/linux/platform_data/atmel.h
> index cea9f70133c5..e26b0c14edea 100644
> --- a/include/linux/platform_data/atmel.h
> +++ b/include/linux/platform_data/atmel.h
> @@ -84,6 +84,7 @@ struct atmel_uart_data {
>   	short			use_dma_rx;	/* use receive DMA? */
>   	void __iomem		*regs;		/* virt. base address, if any */
>   	struct serial_rs485	rs485;		/* rs485 settings */
> +	int			rts_gpio;	/* optional RTS GPIO */
>   };
>
>    /* Touchscreen Controller */
>


-- 
Nicolas Ferre



More information about the linux-arm-kernel mailing list