[PATCH v2 2/4] clk: exynos5410: register clocks using common clock framework
Mauro Ribeiro
mdrjr0 at gmail.com
Fri Nov 1 11:53:33 EDT 2013
Is the PLL35xx driver compatible with the ones used on 5410?
+static struct samsung_pll_clock exynos5410_plls[nr_plls] __initdata = {
+ [apll] = PLL(pll_35xx, CLK_FOUT_APLL, "fout_apll", "fin_pll", APLL_LOCK,
+ APLL_CON0, NULL),
+ [cpll] = PLL(pll_35xx, CLK_FOUT_CPLL, "fout_cpll", "fin_pll", CPLL_LOCK,
+ CPLL_CON0, NULL),
+ [mpll] = PLL(pll_35xx, CLK_FOUT_MPLL, "fout_mpll", "fin_pll", MPLL_LOCK,
+ MPLL_CON0, NULL),
+ [bpll] = PLL(pll_35xx, CLK_FOUT_BPLL, "fout_bpll", "fin_pll", BPLL_LOCK,
+ BPLL_CON0, NULL),
+ [kpll] = PLL(pll_35xx, CLK_FOUT_KPLL, "fout_kpll", "fin_pll", KPLL_LOCK,
+ KPLL_CON0, NULL),
It registers all the PLL's with the same PLL. While the manual says
others PLL names.
Regards,
Mauro
On Tue, Oct 22, 2013 at 7:44 AM, Mike Turquette <mturquette at linaro.org> wrote:
> Quoting Vyacheslav Tyrtov (2013-10-14 08:08:23)
>> From: Tarek Dakhran <t.dakhran at samsung.com>
>>
>> The EXYNOS5410 clocks are statically listed and registered
>> using the Samsung specific common clock helper functions.
>>
>> Signed-off-by: Tarek Dakhran <t.dakhran at samsung.com>
>> Signed-off-by: Vyacheslav Tyrtov <v.tyrtov at samsung.com>
>
> Looks good to me. Any objections for me to take this through the clk
> tree?
>
> Regards,
> Mike
>
>> ---
>> .../devicetree/bindings/clock/exynos5410-clock.txt | 37 +++
>> drivers/clk/samsung/Makefile | 1 +
>> drivers/clk/samsung/clk-exynos5410.c | 251 +++++++++++++++++++++
>> include/dt-bindings/clock/exynos5410.h | 175 ++++++++++++++
>> 4 files changed, 464 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/clock/exynos5410-clock.txt
>> create mode 100644 drivers/clk/samsung/clk-exynos5410.c
>> create mode 100644 include/dt-bindings/clock/exynos5410.h
>>
>> diff --git a/Documentation/devicetree/bindings/clock/exynos5410-clock.txt b/Documentation/devicetree/bindings/clock/exynos5410-clock.txt
>> new file mode 100644
>> index 0000000..a462da231
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/clock/exynos5410-clock.txt
>> @@ -0,0 +1,37 @@
>> +* Samsung Exynos5410 Clock Controller
>> +
>> +The Exynos5410 clock controller generates and supplies clock to various
>> +controllers within the Exynos5410 SoC.
>> +
>> +Required Properties:
>> +
>> +- compatible: should be "samsung,exynos5410-clock"
>> +
>> +- reg: physical base address of the controller and length of memory mapped
>> + region.
>> +
>> +- #clock-cells: should be 1.
>> +
>> +All available clocks are defined as preprocessor macros in
>> +dt-bindings/clock/exynos5410.h header and can be used in device
>> +tree sources.
>> +
>> +Example 1: An example of a clock controller node is listed below.
>> +
>> + clock: clock-controller at 0x10010000 {
>> + compatible = "samsung,exynos5410-clock";
>> + reg = <0x10010000 0x30000>;
>> + #clock-cells = <1>;
>> + };
>> +
>> +Example 2: UART controller node that consumes the clock generated by the clock
>> + controller. Refer to the standard clock bindings for information
>> + about 'clocks' and 'clock-names' property.
>> +
>> + serial at 12C20000 {
>> + compatible = "samsung,exynos4210-uart";
>> + reg = <0x12C00000 0x100>;
>> + interrupts = <0 51 0>;
>> + clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>;
>> + clock-names = "uart", "clk_uart_baud0";
>> + };
>> diff --git a/drivers/clk/samsung/Makefile b/drivers/clk/samsung/Makefile
>> index 3413380..5a446ca 100644
>> --- a/drivers/clk/samsung/Makefile
>> +++ b/drivers/clk/samsung/Makefile
>> @@ -5,6 +5,7 @@
>> obj-$(CONFIG_COMMON_CLK) += clk.o clk-pll.o
>> obj-$(CONFIG_ARCH_EXYNOS4) += clk-exynos4.o
>> obj-$(CONFIG_SOC_EXYNOS5250) += clk-exynos5250.o
>> +obj-$(CONFIG_SOC_EXYNOS5410) += clk-exynos5410.o
>> obj-$(CONFIG_SOC_EXYNOS5420) += clk-exynos5420.o
>> obj-$(CONFIG_SOC_EXYNOS5440) += clk-exynos5440.o
>> obj-$(CONFIG_ARCH_EXYNOS) += clk-exynos-audss.o
>> diff --git a/drivers/clk/samsung/clk-exynos5410.c b/drivers/clk/samsung/clk-exynos5410.c
>> new file mode 100644
>> index 0000000..c5eba08
>> --- /dev/null
>> +++ b/drivers/clk/samsung/clk-exynos5410.c
>> @@ -0,0 +1,251 @@
>> +/*
>> + * Copyright (c) 2013 Samsung Electronics Co., Ltd.
>> + * Author: Tarek Dakhran <t.dakhran at samsung.com>
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 as
>> + * published by the Free Software Foundation.
>> + *
>> + * Common Clock Framework support for Exynos5410 SoC.
>> +*/
>> +
>> +#include <dt-bindings/clock/exynos5410.h>
>> +
>> +#include <linux/clk.h>
>> +#include <linux/clkdev.h>
>> +#include <linux/clk-provider.h>
>> +#include <linux/of.h>
>> +#include <linux/of_address.h>
>> +
>> +#include "clk.h"
>> +
>> +#define APLL_LOCK 0x0
>> +#define APLL_CON0 0x100
>> +#define CPLL_LOCK 0x10020
>> +#define CPLL_CON0 0x10120
>> +#define MPLL_LOCK 0x4000
>> +#define MPLL_CON0 0x4100
>> +#define BPLL_LOCK 0x20010
>> +#define BPLL_CON0 0x20110
>> +#define KPLL_LOCK 0x28000
>> +#define KPLL_CON0 0x28100
>> +
>> +#define SRC_CPU 0x200
>> +#define DIV_CPU0 0x500
>> +#define SRC_CPERI1 0x4204
>> +#define DIV_TOP0 0x10510
>> +#define DIV_TOP1 0x10514
>> +#define DIV_FSYS1 0x1054c
>> +#define DIV_FSYS2 0x10550
>> +#define DIV_PERIC0 0x10558
>> +#define SRC_TOP0 0x10210
>> +#define SRC_TOP1 0x10214
>> +#define SRC_TOP2 0x10218
>> +#define SRC_FSYS 0x10244
>> +#define SRC_PERIC0 0x10250
>> +#define SRC_MASK_FSYS 0x10340
>> +#define SRC_MASK_PERIC0 0x10350
>> +#define GATE_BUS_FSYS0 0x10740
>> +#define GATE_IP_FSYS 0x10944
>> +#define GATE_IP_PERIC 0x10950
>> +#define GATE_IP_PERIS 0x10960
>> +#define SRC_CDREX 0x20200
>> +#define SRC_KFC 0x28200
>> +#define DIV_KFC0 0x28500
>> +
>> +/* list of PLLs */
>> +enum exynos5410_plls {
>> + apll, cpll, mpll,
>> + bpll, kpll,
>> + nr_plls /* number of PLLs */
>> +};
>> +
>> +/*
>> + * list of controller registers to be saved and restored during a
>> + * suspend/resume cycle.
>> + */
>> +static unsigned long exynos5410_clk_regs[] __initdata = {
>> + SRC_CPU,
>> + DIV_CPU0,
>> + SRC_CPERI1,
>> + DIV_TOP0,
>> + DIV_TOP1,
>> + DIV_FSYS1,
>> + DIV_FSYS2,
>> + DIV_PERIC0,
>> + SRC_TOP0,
>> + SRC_TOP1,
>> + SRC_TOP2,
>> + SRC_FSYS,
>> + SRC_PERIC0,
>> + SRC_MASK_FSYS,
>> + SRC_MASK_PERIC0,
>> + GATE_BUS_FSYS0,
>> + GATE_IP_FSYS,
>> + GATE_IP_PERIC,
>> + GATE_IP_PERIS,
>> + SRC_CDREX,
>> + SRC_KFC,
>> + DIV_KFC0,
>> +};
>> +
>> +/* list of all parent clocks */
>> +PNAME(apll_p) = { "fin_pll", "fout_apll", };
>> +PNAME(bpll_p) = { "fin_pll", "fout_bpll", };
>> +PNAME(cpll_p) = { "fin_pll", "fout_cpll" };
>> +PNAME(mpll_p) = { "fin_pll", "fout_mpll", };
>> +PNAME(kpll_p) = { "fin_pll", "fout_kpll", };
>> +
>> +PNAME(mout_cpu_p) = { "mout_apll", "sclk_mpll", };
>> +PNAME(mout_kfc_p) = { "mout_kpll", "sclk_mpll", };
>> +
>> +PNAME(mpll_user_p) = { "fin_pll", "sclk_mpll", };
>> +PNAME(bpll_user_p) = { "fin_pll", "sclk_bpll", };
>> +PNAME(mpll_bpll_p) = { "sclk_mpll_muxed", "sclk_bpll_muxed", };
>> +
>> +PNAME(group2_p) = { "fin_pll", "fin_pll", "none", "none",
>> + "none", "none", "sclk_mpll_bpll",
>> + "none", "none", "sclk_cpll" };
>> +
>> +/* fixed rate clocks generated outside the soc */
>> +static struct samsung_fixed_rate_clock exynos5410_frt_ext_clks[] __initdata = {
>> + FRATE(CLK_FIN_PLL, "fin_pll", NULL, CLK_IS_ROOT, 0),
>> +};
>> +
>> +static struct samsung_mux_clock exynos5410_mux_clks[] __initdata = {
>> + MUX(0, "mout_apll", apll_p, SRC_CPU, 0, 1),
>> + MUX(0, "mout_cpu", mout_cpu_p, SRC_CPU, 16, 1),
>> +
>> + MUX(0, "mout_kpll", kpll_p, SRC_KFC, 0, 1),
>> + MUX(0, "mout_kfc", mout_kfc_p, SRC_KFC, 16, 1),
>> +
>> + MUX(0, "sclk_mpll", mpll_p, SRC_CPERI1, 8, 1),
>> + MUX(0, "sclk_mpll_muxed", mpll_user_p, SRC_TOP2, 20, 1),
>> +
>> + MUX(0, "sclk_bpll", bpll_p, SRC_CDREX, 0, 1),
>> + MUX(0, "sclk_bpll_muxed", bpll_user_p, SRC_TOP2, 24, 1),
>> +
>> + MUX(0, "sclk_cpll", cpll_p, SRC_TOP2, 8, 1),
>> +
>> + MUX(0, "sclk_mpll_bpll", mpll_bpll_p, SRC_TOP1, 20, 1),
>> +
>> + MUX(0, "mout_mmc0", group2_p, SRC_FSYS, 0, 4),
>> + MUX(0, "mout_mmc1", group2_p, SRC_FSYS, 4, 4),
>> + MUX(0, "mout_mmc2", group2_p, SRC_FSYS, 8, 4),
>> +
>> + MUX(0, "mout_uart0", group2_p, SRC_PERIC0, 0, 4),
>> + MUX(0, "mout_uart1", group2_p, SRC_PERIC0, 4, 4),
>> + MUX(0, "mout_uart2", group2_p, SRC_PERIC0, 8, 4),
>> +
>> + MUX(0, "mout_aclk200", mpll_bpll_p, SRC_TOP0, 12, 1),
>> + MUX(0, "mout_aclk400", mpll_bpll_p, SRC_TOP0, 20, 1),
>> +};
>> +
>> +static struct samsung_div_clock exynos5410_div_clks[] __initdata = {
>> + DIV(0, "div_arm", "mout_cpu", DIV_CPU0, 0, 3),
>> + DIV(0, "div_arm2", "div_arm", DIV_CPU0, 28, 3),
>> +
>> + DIV(0, "div_acp", "div_arm2", DIV_CPU0, 8, 3),
>> + DIV(0, "div_cpud", "div_arm2", DIV_CPU0, 4, 3),
>> + DIV(0, "div_atb", "div_arm2", DIV_CPU0, 16, 3),
>> + DIV(0, "pclk_dbg", "div_arm2", DIV_CPU0, 20, 3),
>> +
>> + DIV(0, "div_kfc", "mout_kfc", DIV_KFC0, 0, 3),
>> + DIV(0, "div_aclk", "div_kfc", DIV_KFC0, 4, 3),
>> + DIV(0, "div_pclk", "div_kfc", DIV_KFC0, 20, 3),
>> +
>> + DIV(0, "aclk66_pre", "sclk_mpll_muxed", DIV_TOP1, 24, 3),
>> + DIV(0, "aclk66", "aclk66_pre", DIV_TOP0, 0, 3),
>> +
>> + DIV(0, "div_mmc0", "mout_mmc0", DIV_FSYS1, 0, 4),
>> + DIV(0, "div_mmc1", "mout_mmc1", DIV_FSYS1, 16, 4),
>> + DIV(0, "div_mmc2", "mout_mmc2", DIV_FSYS2, 0, 4),
>> +
>> + DIV_F(0, "div_mmc_pre0", "div_mmc0",
>> + DIV_FSYS1, 8, 8, CLK_SET_RATE_PARENT, 0),
>> + DIV_F(0, "div_mmc_pre1", "div_mmc1",
>> + DIV_FSYS1, 24, 8, CLK_SET_RATE_PARENT, 0),
>> + DIV_F(0, "div_mmc_pre2", "div_mmc2",
>> + DIV_FSYS2, 8, 8, CLK_SET_RATE_PARENT, 0),
>> +
>> + DIV(0, "div_uart0", "mout_uart0", DIV_PERIC0, 0, 4),
>> + DIV(0, "div_uart1", "mout_uart1", DIV_PERIC0, 4, 4),
>> + DIV(0, "div_uart2", "mout_uart2", DIV_PERIC0, 8, 4),
>> + DIV(0, "div_uart3", "mout_uart3", DIV_PERIC0, 12, 4),
>> +
>> + DIV(0, "aclk200", "mout_aclk200", DIV_TOP0, 12, 3),
>> + DIV(0, "aclk400", "mout_aclk400", DIV_TOP0, 24, 3),
>> +};
>> +
>> +static struct samsung_gate_clock exynos5410_gate_clks[] __initdata = {
>> + GATE(CLK_MCT, "mct", "aclk66", GATE_IP_PERIS, 18, 0, 0),
>> +
>> + GATE(CLK_SCLK_MMC0, "sclk_mmc0", "div_mmc_pre0",
>> + SRC_MASK_FSYS, 0, CLK_SET_RATE_PARENT, 0),
>> + GATE(CLK_SCLK_MMC1, "sclk_mmc1", "div_mmc_pre1",
>> + SRC_MASK_FSYS, 4, CLK_SET_RATE_PARENT, 0),
>> + GATE(CLK_SCLK_MMC2, "sclk_mmc2", "div_mmc_pre2",
>> + SRC_MASK_FSYS, 8, CLK_SET_RATE_PARENT, 0),
>> +
>> + GATE(CLK_MMC0, "sdmmc0", "aclk200", GATE_BUS_FSYS0, 12, 0, 0),
>> + GATE(CLK_MMC1, "sdmmc1", "aclk200", GATE_BUS_FSYS0, 13, 0, 0),
>> + GATE(CLK_MMC2, "sdmmc2", "aclk200", GATE_BUS_FSYS0, 14, 0, 0),
>> +
>> + GATE(CLK_UART0, "uart0", "aclk66", GATE_IP_PERIC, 0, 0, 0),
>> + GATE(CLK_UART1, "uart1", "aclk66", GATE_IP_PERIC, 1, 0, 0),
>> + GATE(CLK_UART2, "uart2", "aclk66", GATE_IP_PERIC, 2, 0, 0),
>> +
>> + GATE(CLK_SCLK_UART0, "sclk_uart0", "div_uart0",
>> + SRC_MASK_PERIC0, 0, CLK_SET_RATE_PARENT, 0),
>> + GATE(CLK_SCLK_UART1, "sclk_uart1", "div_uart1",
>> + SRC_MASK_PERIC0, 4, CLK_SET_RATE_PARENT, 0),
>> + GATE(CLK_SCLK_UART2, "sclk_uart2", "div_uart2",
>> + SRC_MASK_PERIC0, 8, CLK_SET_RATE_PARENT, 0),
>> +};
>> +
>> +static struct samsung_pll_clock exynos5410_plls[nr_plls] __initdata = {
>> + [apll] = PLL(pll_35xx, CLK_FOUT_APLL, "fout_apll", "fin_pll", APLL_LOCK,
>> + APLL_CON0, NULL),
>> + [cpll] = PLL(pll_35xx, CLK_FOUT_CPLL, "fout_cpll", "fin_pll", CPLL_LOCK,
>> + CPLL_CON0, NULL),
>> + [mpll] = PLL(pll_35xx, CLK_FOUT_MPLL, "fout_mpll", "fin_pll", MPLL_LOCK,
>> + MPLL_CON0, NULL),
>> + [bpll] = PLL(pll_35xx, CLK_FOUT_BPLL, "fout_bpll", "fin_pll", BPLL_LOCK,
>> + BPLL_CON0, NULL),
>> + [kpll] = PLL(pll_35xx, CLK_FOUT_KPLL, "fout_kpll", "fin_pll", KPLL_LOCK,
>> + KPLL_CON0, NULL),
>> +};
>> +
>> +static struct of_device_id ext_clk_match[] __initdata = {
>> + { .compatible = "samsung,clock-oscclk", .data = (void *)0, },
>> + { },
>> +};
>> +
>> +/* register exynos5410 clocks */
>> +static void __init exynos5410_clk_init(struct device_node *np)
>> +{
>> + void __iomem *reg_base;
>> +
>> + reg_base = of_iomap(np, 0);
>> + if (!reg_base)
>> + panic("%s: failed to map registers\n", __func__);
>> +
>> + samsung_clk_init(np, reg_base, CLK_NR_CLKS,
>> + exynos5410_clk_regs, ARRAY_SIZE(exynos5410_clk_regs),
>> + NULL, 0);
>> + samsung_clk_of_register_fixed_ext(exynos5410_frt_ext_clks,
>> + ARRAY_SIZE(exynos5410_frt_ext_clks),
>> + ext_clk_match);
>> + samsung_clk_register_pll(exynos5410_plls, ARRAY_SIZE(exynos5410_plls),
>> + reg_base);
>> +
>> + samsung_clk_register_mux(exynos5410_mux_clks,
>> + ARRAY_SIZE(exynos5410_mux_clks));
>> + samsung_clk_register_div(exynos5410_div_clks,
>> + ARRAY_SIZE(exynos5410_div_clks));
>> + samsung_clk_register_gate(exynos5410_gate_clks,
>> + ARRAY_SIZE(exynos5410_gate_clks));
>> +
>> + pr_debug("Exynos5410: clock setup completed.\n");
>> +}
>> +CLK_OF_DECLARE(exynos5410_clk, "samsung,exynos5410-clock", exynos5410_clk_init);
>> diff --git a/include/dt-bindings/clock/exynos5410.h b/include/dt-bindings/clock/exynos5410.h
>> new file mode 100644
>> index 0000000..9b4a58b
>> --- /dev/null
>> +++ b/include/dt-bindings/clock/exynos5410.h
>> @@ -0,0 +1,175 @@
>> +#ifndef _DT_BINDINGS_CLOCK_EXYNOS_5410_H
>> +#define _DT_BINDINGS_CLOCK_EXYNOS_5410_H
>> +
>> +/* core clocks */
>> +#define CLK_FIN_PLL 1
>> +#define CLK_FOUT_APLL 2
>> +#define CLK_FOUT_CPLL 3
>> +#define CLK_FOUT_DPLL 4
>> +#define CLK_FOUT_EPLL 5
>> +#define CLK_FOUT_RPLL 6
>> +#define CLK_FOUT_IPLL 7
>> +#define CLK_FOUT_SPLL 8
>> +#define CLK_FOUT_VPLL 9
>> +#define CLK_FOUT_MPLL 10
>> +#define CLK_FOUT_BPLL 11
>> +#define CLK_FOUT_KPLL 12
>> +
>> +/* gate for special clocks (sclk) */
>> +#define CLK_SCLK_UART0 128
>> +#define CLK_SCLK_UART1 129
>> +#define CLK_SCLK_UART2 130
>> +#define CLK_SCLK_UART3 131
>> +#define CLK_SCLK_MMC0 132
>> +#define CLK_SCLK_MMC1 133
>> +#define CLK_SCLK_MMC2 134
>> +#define CLK_SCLK_SPI0 135
>> +#define CLK_SCLK_SPI1 136
>> +#define CLK_SCLK_SPI2 137
>> +#define CLK_SCLK_I2S1 138
>> +#define CLK_SCLK_I2S2 139
>> +#define CLK_SCLK_PCM1 140
>> +#define CLK_SCLK_PCM2 141
>> +#define CLK_SCLK_SPDIF 142
>> +#define CLK_SCLK_HDMI 143
>> +#define CLK_SCLK_PIXEL 144
>> +#define CLK_SCLK_DP1 145
>> +#define CLK_SCLK_MIPI1 146
>> +#define CLK_SCLK_FIMD1 147
>> +#define CLK_SCLK_MAUDIO0 148
>> +#define CLK_SCLK_MAUPCM0 149
>> +#define CLK_SCLK_USBD300 150
>> +#define CLK_SCLK_USBD301 151
>> +#define CLK_SCLK_USBPHY300 152
>> +#define CLK_SCLK_USBPHY301 153
>> +#define CLK_SCLK_UNIPRO 154
>> +#define CLK_SCLK_PWM 155
>> +#define CLK_SCLK_GSCL_WA 156
>> +#define CLK_SCLK_GSCL_WB 157
>> +#define CLK_SCLK_HDMIPHY 158
>> +
>> +/* gate clocks */
>> +#define CLK_ACLK66_PERIC 256
>> +#define CLK_UART0 257
>> +#define CLK_UART1 258
>> +#define CLK_UART2 259
>> +#define CLK_UART3 260
>> +#define CLK_I2C0 261
>> +#define CLK_I2C1 262
>> +#define CLK_I2C2 263
>> +#define CLK_I2C3 264
>> +#define CLK_I2C4 265
>> +#define CLK_I2C5 266
>> +#define CLK_I2C6 267
>> +#define CLK_I2C7 268
>> +#define CLK_I2C_HDMI 269
>> +#define CLK_TSADC 270
>> +#define CLK_SPI0 271
>> +#define CLK_SPI1 272
>> +#define CLK_SPI2 273
>> +#define CLK_KEYIF 274
>> +#define CLK_I2S1 275
>> +#define CLK_I2S2 276
>> +#define CLK_PCM1 277
>> +#define CLK_PCM2 278
>> +#define CLK_PWM 279
>> +#define CLK_SPDIF 280
>> +#define CLK_I2C8 281
>> +#define CLK_I2C9 282
>> +#define CLK_I2C10 283
>> +#define CLK_ACLK66_PSGEN 300
>> +#define CLK_CHIPID 301
>> +#define CLK_SYSREG 302
>> +#define CLK_TZPC0 303
>> +#define CLK_TZPC1 304
>> +#define CLK_TZPC2 305
>> +#define CLK_TZPC3 306
>> +#define CLK_TZPC4 307
>> +#define CLK_TZPC5 308
>> +#define CLK_TZPC6 309
>> +#define CLK_TZPC7 310
>> +#define CLK_TZPC8 311
>> +#define CLK_TZPC9 312
>> +#define CLK_HDMI_CEC 313
>> +#define CLK_SECKEY 314
>> +#define CLK_MCT 315
>> +#define CLK_WDT 316
>> +#define CLK_RTC 317
>> +#define CLK_TMU 318
>> +#define CLK_TMU_GPU 319
>> +#define CLK_PCLK66_GPIO 330
>> +#define CLK_ACLK200_FSYS2 350
>> +#define CLK_MMC0 351
>> +#define CLK_MMC1 352
>> +#define CLK_MMC2 353
>> +#define CLK_SROMC 354
>> +#define CLK_UFS 355
>> +#define CLK_ACLK200_FSYS 360
>> +#define CLK_TSI 361
>> +#define CLK_PDMA0 362
>> +#define CLK_PDMA1 363
>> +#define CLK_RTIC 364
>> +#define CLK_USBH20 365
>> +#define CLK_USBD300 366
>> +#define CLK_USBD301 367
>> +#define CLK_ACLK400_MSCL 380
>> +#define CLK_MSCL0 381
>> +#define CLK_MSCL1 382
>> +#define CLK_MSCL2 383
>> +#define CLK_SMMU_MSCL0 384
>> +#define CLK_SMMU_MSCL1 385
>> +#define CLK_SMMU_MSCL2 386
>> +#define CLK_ACLK333 400
>> +#define CLK_MFC 401
>> +#define CLK_SMMU_MFCL 402
>> +#define CLK_SMMU_MFCR 403
>> +#define CLK_ACLK200_DISP1 410
>> +#define CLK_DSIM1 411
>> +#define CLK_DP1 412
>> +#define CLK_HDMI 413
>> +#define CLK_ACLK300_DISP1 420
>> +#define CLK_FIMD1 421
>> +#define CLK_SMMU_FIMD1 422
>> +#define CLK_ACLK166 430
>> +#define CLK_MIXER 431
>> +#define CLK_ACLK266 440
>> +#define CLK_ROTATOR 441
>> +#define CLK_MDMA1 442
>> +#define CLK_SMMU_ROTATOR 443
>> +#define CLK_SMMU_MDMA1 444
>> +#define CLK_ACLK300_JPEG 450
>> +#define CLK_JPEG 451
>> +#define CLK_JPEG2 452
>> +#define CLK_SMMU_JPEG 453
>> +#define CLK_ACLK300_GSCL 460
>> +#define CLK_SMMU_GSCL0 461
>> +#define CLK_SMMU_GSCL1 462
>> +#define CLK_GSCL_WA 463
>> +#define CLK_GSCL_WB 464
>> +#define CLK_GSCL0 465
>> +#define CLK_GSCL1 466
>> +#define CLK_CLK_3AA 467
>> +#define CLK_ACLK266_G2D 470
>> +#define CLK_SSS 471
>> +#define CLK_SLIM_SSS 472
>> +#define CLK_MDMA0 473
>> +#define CLK_ACLK333_G2D 480
>> +#define CLK_G2D 481
>> +#define CLK_ACLK333_432_GSCL 490
>> +#define CLK_SMMU_3AA 491
>> +#define CLK_SMMU_FIMCL0 492
>> +#define CLK_SMMU_FIMCL1 493
>> +#define CLK_SMMU_FIMCL3 494
>> +#define CLK_FIMC_LITE3 495
>> +#define CLK_ACLK_G3D 500
>> +#define CLK_G3D 501
>> +#define CLK_SMMU_MIXER 502
>> +
>> +/* mux clocks */
>> +#define CLK_MOUT_HDMI 640
>> +
>> +/* divider clocks */
>> +#define CLK_DOUT_PIXEL 768
>> +#define CLK_NR_CLKS 769
>> +
>> +#endif /* _DT_BINDINGS_CLOCK_EXYNOS_5410_H */
>> --
>> 1.8.1.5
> --
> To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
More information about the linux-arm-kernel
mailing list