[PATCH v5 12/13] ARM: kirkwood: remove redundant DT board files

[Arnaud Ebalard]

Hi Jason and Sebastian,

Sebastian Hesselbarth <sebastian.hesselbarth at gmail.com> writes:

> With DT support for mv643xx_eth board specific init for some boards now
> is unneccessary. Remove those board files, Kconfig entries, and
> corresponding entries in kirkwood_defconfig.
>
> Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth at gmail.com>
> ---
> Note: board-km_kirkwood.c is also removed, as Valentin Longchamp confirmed
> the lock-up is not caused by accessing clock gating registers but rather
> non-existent device registers. This will be addressed by dtsi separation
> for kirkwood and bobcat SoC variants.
>
> Changelog:
> v3->v4:
> - remove more boards that don't require board specific setup
>
> Cc: David Miller <davem at davemloft.net>
> Cc: Lennert Buytenhek <buytenh at wantstofly.org>
> Cc: Jason Cooper <jason at lakedaemon.net>
> Cc: Andrew Lunn <andrew at lunn.ch>
> Cc: Benjamin Herrenschmidt <benh at kernel.crashing.org>
> Cc: netdev at vger.kernel.org
> Cc: linux-arm-kernel at lists.infradead.org
> Cc: linuxppc-dev at lists.ozlabs.org
> Cc: linux-kernel at vger.kernel.org
> ---
>  arch/arm/configs/kirkwood_defconfig           |   16 ----
>  arch/arm/mach-kirkwood/Kconfig                |  117 -------------------------
>  arch/arm/mach-kirkwood/Makefile               |   16 ----
>  arch/arm/mach-kirkwood/board-dnskw.c          |    7 --
>  arch/arm/mach-kirkwood/board-dockstar.c       |   32 -------
>  arch/arm/mach-kirkwood/board-dreamplug.c      |   35 --------
>  arch/arm/mach-kirkwood/board-dt.c             |   62 +------------
>  arch/arm/mach-kirkwood/board-goflexnet.c      |   34 -------
>  arch/arm/mach-kirkwood/board-guruplug.c       |   33 -------
>  arch/arm/mach-kirkwood/board-ib62x0.c         |   29 ------
>  arch/arm/mach-kirkwood/board-iconnect.c       |   10 ---
>  arch/arm/mach-kirkwood/board-iomega_ix2_200.c |   34 -------
>  arch/arm/mach-kirkwood/board-km_kirkwood.c    |   44 ----------
>  arch/arm/mach-kirkwood/board-lsxl.c           |   16 ----
>  arch/arm/mach-kirkwood/board-mplcec4.c        |   14 ---
>  arch/arm/mach-kirkwood/board-ns2.c            |   35 --------
>  arch/arm/mach-kirkwood/board-openblocks_a6.c  |   26 ------
>  arch/arm/mach-kirkwood/board-readynas.c       |    6 --

Just a stupid note: With Thomas ongoing work to get mvebu-pcie driver in
place and enabled for kirkwood, some boards setup files will also lose
their pcie init routines, which may allow you to kill those additonal
files soon.

For instance 6bd98481ab34 (arm: kirkwood: NETGEAR ReadyNAS Duo v2 init
PCIe via DT) currently sitting in jcooper/mvebu/pcie_kirkwood removes
the PCIE init routine in board-readynas.c, and yours remove ge00
init. With both applied, the whole file can go away.

AFAICT, this may be the case soon for:

 arch/arm/mach-kirkwood/board-iconnect.c   (36e5722089)
 arch/arm/mach-kirkwood/board-mplcec4.c    (9470fbfb8d)
 arch/arm/mach-kirkwood/board-nsa310.c     (40fa8e5da2)
 arch/arm/mach-kirkwood/board-readynas.c   (6bd98481ab)
 arch/arm/mach-kirkwood/board-ts219.c      (259e234608)

Anyway, thanks for this work Sebastian.

Cheers,

a+