[BISECTED] 3.10-rc1 OMAP1 GPIO IRQ regression

[Jon Hunter]

On 26/05/13 20:07, Aaro Koskinen wrote:
> On Thu, May 23, 2013 at 08:02:05PM +0100, Jon Hunter wrote:
>> On 22/05/13 22:20, Aaro Koskinen wrote:
>>> On Tue, May 21, 2013 at 08:37:16PM +0100, Jon Hunter wrote:
>>>> On 21/05/13 18:39, Aaro Koskinen wrote:
>>>>> On Mon, May 20, 2013 at 10:46:21AM -0700, Tony Lindgren wrote:
>>>>>> * Tony Lindgren <tony at atomide.com> [130516 14:50]:
>>>>>>> * Aaro Koskinen <aaro.koskinen at iki.fi> [130516 14:05]:
>>>>>>>> On Thu, May 16, 2013 at 11:09:34AM -0700, Tony Lindgren wrote:
>>>>>>>>> * Aaro Koskinen <aaro.koskinen at iki.fi> [130513 13:58]:
>>>>>>>>>> I tested 3.10-rc1 on OMAP1 / Nokia 770, and Retu MFD probe is broken:
>>>>>>>>>>
>>>>>>>>>> [    2.264221] retu-mfd 2-0001: Retu v3.2 found
>>>>>>>>>> [    2.281951] retu-mfd 2-0001: Failed to allocate IRQs: -12
>>>>>>>>>> [    2.300140] retu-mfd: probe of 2-0001 failed with error -12
>>>>>>>>>>
>>>>>>>>>> The error is coming from regmap code. According to git bisect, it is
>>>>>>>>>> caused by:
>>>>>>>>>>
>>>>>>>>>> 	commit ede4d7a5b9835510fd1f724367f68d2fa4128453
>>>>>>>>>> 	Author: Jon Hunter <jon-hunter at ti.com>
>>>>>>>>>> 	Date:   Fri Mar 1 11:22:47 2013 -0600
>>>>>>>>>>
>>>>>>>>>> 	    gpio/omap: convert gpio irq domain to linear mapping
>>>>>>>>>>
>>>>>>>>>> The commit does not anymore revert cleanly, and I haven't yet tried
>>>>>>>>>> crafting a manual revert, so any fix proposals/ideas are welcome...
>>>>>>>>>
>>>>>>>>> Hmm this might be a bit trickier to fix. Obviously the real solution
>>>>>>>>> is to convert omap1 to SPARSE_IRQ like we did for omap2+.
>>>>>>>>>
>>>>>>>>> For the -rc cycle, it might be possible to fix this by adding a
>>>>>>>>> different irq_to_gpio() and gpio_to_irq() functions for omap1.
>>>>>>>>
>>>>>>>> The commit reverts cleanly if we also revert
>>>>>>>> 3513cdeccc647d41c4a9ff923af17deaaac04a66 (gpio/omap: optimise interrupt
>>>>>>>> service routine), which seems to be just some minor optimization. The
>>>>>>>> result is below, and with it 770 works again.
>>>>>>>
>>>>>>> Hmm in this case it seems that we should just fix it rather than go back
>>>>>>> to the old code, so let's take a look at that first.
>>>>>>
>>>>>> Does the following fix it for you or do we need to fix something else
>>>>>> there too?
>>>>>
>>>>> Thanks, that fixes Retu probe on 770.
>>>>
>>>> Sorry for not responding sooner, but I have been moving. 
>>>>
>>>> From looking at the code it appears that the regmap_add_irq_chip()
>>>> is failing in the retu driver. I am not sure if this will work, 
>>>> but have you tried making the following change to the retu driver 
>>>> so that it also uses irq_domain_add_linear() as well? Just a thought ...
>>>
>>> This will trigger WARNING: at drivers/base/regmap/regmap-irq.c:514.
>>
>> Sorry, there is another change needed. Can you try ...
> 
> I don't see much improvement with this. Although Retu probe succeeds,
> genirq error logs are still there. Also none of the GPIO irqs used by
> other drivers seem to be working at all, e.g. touchscreen.

Care to share the log?

Jon