[PATCH v6 09/10] ASoC: fsl: Move fsl-ssi binding doc to sound/
Markus Pargmann
mpa at pengutronix.de
Tue May 28 10:47:57 EDT 2013
fsl-ssi was located in powerpc/fsl/ssi.txt. This is no powerpc specific
device, so it should be moved to sound/ as it connects to differen audio
codecs.
Signed-off-by: Markus Pargmann <mpa at pengutronix.de>
---
.../devicetree/bindings/powerpc/fsl/ssi.txt | 73 ----------------------
.../devicetree/bindings/sound/fsl,ssi.txt | 73 ++++++++++++++++++++++
2 files changed, 73 insertions(+), 73 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/powerpc/fsl/ssi.txt
create mode 100644 Documentation/devicetree/bindings/sound/fsl,ssi.txt
diff --git a/Documentation/devicetree/bindings/powerpc/fsl/ssi.txt b/Documentation/devicetree/bindings/powerpc/fsl/ssi.txt
deleted file mode 100644
index 5ff76c9..0000000
--- a/Documentation/devicetree/bindings/powerpc/fsl/ssi.txt
+++ /dev/null
@@ -1,73 +0,0 @@
-Freescale Synchronous Serial Interface
-
-The SSI is a serial device that communicates with audio codecs. It can
-be programmed in AC97, I2S, left-justified, or right-justified modes.
-
-Required properties:
-- compatible: Compatible list, contains "fsl,ssi".
-- cell-index: The SSI, <0> = SSI1, <1> = SSI2, and so on.
-- reg: Offset and length of the register set for the device.
-- interrupts: <a b> where a is the interrupt number and b is a
- field that represents an encoding of the sense and
- level information for the interrupt. This should be
- encoded based on the information in section 2)
- depending on the type of interrupt controller you
- have.
-- interrupt-parent: The phandle for the interrupt controller that
- services interrupts for this device.
-- fsl,mode: The operating mode for the SSI interface.
- "i2s-slave" - I2S mode, SSI is clock slave
- "i2s-master" - I2S mode, SSI is clock master
- "lj-slave" - left-justified mode, SSI is clock slave
- "lj-master" - l.j. mode, SSI is clock master
- "rj-slave" - right-justified mode, SSI is clock slave
- "rj-master" - r.j., SSI is clock master
- "ac97-slave" - AC97 mode, SSI is clock slave
- "ac97-master" - AC97 mode, SSI is clock master
-- fsl,playback-dma: Phandle to a node for the DMA channel to use for
- playback of audio. This is typically dictated by SOC
- design. See the notes below.
-- fsl,capture-dma: Phandle to a node for the DMA channel to use for
- capture (recording) of audio. This is typically dictated
- by SOC design. See the notes below.
-- fsl,fifo-depth: The number of elements in the transmit and receive FIFOs.
- This number is the maximum allowed value for SFCSR[TFWM0].
-- fsl,ssi-asynchronous:
- If specified, the SSI is to be programmed in asynchronous
- mode. In this mode, pins SRCK, STCK, SRFS, and STFS must
- all be connected to valid signals. In synchronous mode,
- SRCK and SRFS are ignored. Asynchronous mode allows
- playback and capture to use different sample sizes and
- sample rates. Some drivers may require that SRCK and STCK
- be connected together, and SRFS and STFS be connected
- together. This would still allow different sample sizes,
- but not different sample rates.
-
-Optional properties:
-- codec-handle: Phandle to a 'codec' node that defines an audio
- codec connected to this SSI. This node is typically
- a child of an I2C or other control node.
-
-Child 'codec' node required properties:
-- compatible: Compatible list, contains the name of the codec
-
-Child 'codec' node optional properties:
-- clock-frequency: The frequency of the input clock, which typically comes
- from an on-board dedicated oscillator.
-
-Notes on fsl,playback-dma and fsl,capture-dma:
-
-On SOCs that have an SSI, specific DMA channels are hard-wired for playback
-and capture. On the MPC8610, for example, SSI1 must use DMA channel 0 for
-playback and DMA channel 1 for capture. SSI2 must use DMA channel 2 for
-playback and DMA channel 3 for capture. The developer can choose which
-DMA controller to use, but the channels themselves are hard-wired. The
-purpose of these two properties is to represent this hardware design.
-
-The device tree nodes for the DMA channels that are referenced by
-"fsl,playback-dma" and "fsl,capture-dma" must be marked as compatible with
-"fsl,ssi-dma-channel". The SOC-specific compatible string (e.g.
-"fsl,mpc8610-dma-channel") can remain. If these nodes are left as
-"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel", then the generic Elo DMA
-drivers (fsldma) will attempt to use them, and it will conflict with the
-sound drivers.
diff --git a/Documentation/devicetree/bindings/sound/fsl,ssi.txt b/Documentation/devicetree/bindings/sound/fsl,ssi.txt
new file mode 100644
index 0000000..5ff76c9
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/fsl,ssi.txt
@@ -0,0 +1,73 @@
+Freescale Synchronous Serial Interface
+
+The SSI is a serial device that communicates with audio codecs. It can
+be programmed in AC97, I2S, left-justified, or right-justified modes.
+
+Required properties:
+- compatible: Compatible list, contains "fsl,ssi".
+- cell-index: The SSI, <0> = SSI1, <1> = SSI2, and so on.
+- reg: Offset and length of the register set for the device.
+- interrupts: <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and
+ level information for the interrupt. This should be
+ encoded based on the information in section 2)
+ depending on the type of interrupt controller you
+ have.
+- interrupt-parent: The phandle for the interrupt controller that
+ services interrupts for this device.
+- fsl,mode: The operating mode for the SSI interface.
+ "i2s-slave" - I2S mode, SSI is clock slave
+ "i2s-master" - I2S mode, SSI is clock master
+ "lj-slave" - left-justified mode, SSI is clock slave
+ "lj-master" - l.j. mode, SSI is clock master
+ "rj-slave" - right-justified mode, SSI is clock slave
+ "rj-master" - r.j., SSI is clock master
+ "ac97-slave" - AC97 mode, SSI is clock slave
+ "ac97-master" - AC97 mode, SSI is clock master
+- fsl,playback-dma: Phandle to a node for the DMA channel to use for
+ playback of audio. This is typically dictated by SOC
+ design. See the notes below.
+- fsl,capture-dma: Phandle to a node for the DMA channel to use for
+ capture (recording) of audio. This is typically dictated
+ by SOC design. See the notes below.
+- fsl,fifo-depth: The number of elements in the transmit and receive FIFOs.
+ This number is the maximum allowed value for SFCSR[TFWM0].
+- fsl,ssi-asynchronous:
+ If specified, the SSI is to be programmed in asynchronous
+ mode. In this mode, pins SRCK, STCK, SRFS, and STFS must
+ all be connected to valid signals. In synchronous mode,
+ SRCK and SRFS are ignored. Asynchronous mode allows
+ playback and capture to use different sample sizes and
+ sample rates. Some drivers may require that SRCK and STCK
+ be connected together, and SRFS and STFS be connected
+ together. This would still allow different sample sizes,
+ but not different sample rates.
+
+Optional properties:
+- codec-handle: Phandle to a 'codec' node that defines an audio
+ codec connected to this SSI. This node is typically
+ a child of an I2C or other control node.
+
+Child 'codec' node required properties:
+- compatible: Compatible list, contains the name of the codec
+
+Child 'codec' node optional properties:
+- clock-frequency: The frequency of the input clock, which typically comes
+ from an on-board dedicated oscillator.
+
+Notes on fsl,playback-dma and fsl,capture-dma:
+
+On SOCs that have an SSI, specific DMA channels are hard-wired for playback
+and capture. On the MPC8610, for example, SSI1 must use DMA channel 0 for
+playback and DMA channel 1 for capture. SSI2 must use DMA channel 2 for
+playback and DMA channel 3 for capture. The developer can choose which
+DMA controller to use, but the channels themselves are hard-wired. The
+purpose of these two properties is to represent this hardware design.
+
+The device tree nodes for the DMA channels that are referenced by
+"fsl,playback-dma" and "fsl,capture-dma" must be marked as compatible with
+"fsl,ssi-dma-channel". The SOC-specific compatible string (e.g.
+"fsl,mpc8610-dma-channel") can remain. If these nodes are left as
+"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel", then the generic Elo DMA
+drivers (fsldma) will attempt to use them, and it will conflict with the
+sound drivers.
--
1.8.2.1
More information about the linux-arm-kernel
mailing list