[PATCH 5/5] ARM: at91: dt: switch to standard IRQ flag defines
Jean-Christophe PLAGNIOL-VILLARD
plagnioj at jcrosoft.com
Wed May 15 10:03:05 EDT 2013
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj at jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre at atmel.com>
---
arch/arm/boot/dts/at91rm9200.dtsi | 45 +++++++++++---------
arch/arm/boot/dts/at91sam9260.dtsi | 49 ++++++++++++----------
arch/arm/boot/dts/at91sam9263.dtsi | 43 ++++++++++----------
arch/arm/boot/dts/at91sam9g45.dtsi | 49 +++++++++++-----------
arch/arm/boot/dts/at91sam9n12.dtsi | 41 ++++++++++---------
arch/arm/boot/dts/at91sam9x5.dtsi | 55 +++++++++++++------------
arch/arm/boot/dts/sama5d3.dtsi | 79 ++++++++++++++++++------------------
7 files changed, 188 insertions(+), 173 deletions(-)
diff --git a/arch/arm/boot/dts/at91rm9200.dtsi b/arch/arm/boot/dts/at91rm9200.dtsi
index 361a957..4aad0d9 100644
--- a/arch/arm/boot/dts/at91rm9200.dtsi
+++ b/arch/arm/boot/dts/at91rm9200.dtsi
@@ -12,6 +12,7 @@
#include "skeleton.dtsi"
#include <dt-bindings/pinctrl/at91.h>
+#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
/ {
@@ -79,25 +80,29 @@
st: timer at fffffd00 {
compatible = "atmel,at91rm9200-st";
reg = <0xfffffd00 0x100>;
- interrupts = <1 4 7>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
};
tcb0: timer at fffa0000 {
compatible = "atmel,at91rm9200-tcb";
reg = <0xfffa0000 0x100>;
- interrupts = <17 4 0 18 4 0 19 4 0>;
+ interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0
+ 18 IRQ_TYPE_LEVEL_HIGH 0
+ 19 IRQ_TYPE_LEVEL_HIGH 0>;
};
tcb1: timer at fffa4000 {
compatible = "atmel,at91rm9200-tcb";
reg = <0xfffa4000 0x100>;
- interrupts = <20 4 0 21 4 0 22 4 0>;
+ interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0
+ 21 IRQ_TYPE_LEVEL_HIGH 0
+ 22 IRQ_TYPE_LEVEL_HIGH 0>;
};
i2c0: i2c at fffb8000 {
compatible = "atmel,at91rm9200-i2c";
reg = <0xfffb8000 0x4000>;
- interrupts = <12 4 6>;
+ interrupts = <12 IRQ_TYPE_LEVEL_HIGH 6>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_twi>;
#address-cells = <1>;
@@ -108,7 +113,7 @@
mmc0: mmc at fffb4000 {
compatible = "atmel,hsmci";
reg = <0xfffb4000 0x4000>;
- interrupts = <10 4 0>;
+ interrupts = <10 IRQ_TYPE_LEVEL_HIGH 0>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -117,7 +122,7 @@
ssc0: ssc at fffd0000 {
compatible = "atmel,at91rm9200-ssc";
reg = <0xfffd0000 0x4000>;
- interrupts = <14 4 5>;
+ interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
status = "disable";
@@ -126,7 +131,7 @@
ssc1: ssc at fffd4000 {
compatible = "atmel,at91rm9200-ssc";
reg = <0xfffd4000 0x4000>;
- interrupts = <15 4 5>;
+ interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>;
status = "disable";
@@ -135,7 +140,7 @@
ssc2: ssc at fffd8000 {
compatible = "atmel,at91rm9200-ssc";
reg = <0xfffd8000 0x4000>;
- interrupts = <16 4 5>;
+ interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ssc2_tx &pinctrl_ssc2_rx>;
status = "disable";
@@ -144,7 +149,7 @@
macb0: ethernet at fffbc000 {
compatible = "cdns,at91rm9200-emac", "cdns,emac";
reg = <0xfffbc000 0x4000>;
- interrupts = <24 4 3>;
+ interrupts = <24 IRQ_TYPE_LEVEL_HIGH 3>;
phy-mode = "rmii";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_macb_rmii>;
@@ -396,7 +401,7 @@
pioA: gpio at fffff400 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x200>;
- interrupts = <2 4 1>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -406,7 +411,7 @@
pioB: gpio at fffff600 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff600 0x200>;
- interrupts = <3 4 1>;
+ interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -416,7 +421,7 @@
pioC: gpio at fffff800 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff800 0x200>;
- interrupts = <4 4 1>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -426,7 +431,7 @@
pioD: gpio at fffffa00 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffffa00 0x200>;
- interrupts = <5 4 1>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -437,7 +442,7 @@
dbgu: serial at fffff200 {
compatible = "atmel,at91rm9200-usart";
reg = <0xfffff200 0x200>;
- interrupts = <1 4 7>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_dbgu>;
status = "disabled";
@@ -446,7 +451,7 @@
usart0: serial at fffc0000 {
compatible = "atmel,at91rm9200-usart";
reg = <0xfffc0000 0x200>;
- interrupts = <6 4 5>;
+ interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
@@ -457,7 +462,7 @@
usart1: serial at fffc4000 {
compatible = "atmel,at91rm9200-usart";
reg = <0xfffc4000 0x200>;
- interrupts = <7 4 5>;
+ interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
@@ -468,7 +473,7 @@
usart2: serial at fffc8000 {
compatible = "atmel,at91rm9200-usart";
reg = <0xfffc8000 0x200>;
- interrupts = <8 4 5>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
@@ -479,7 +484,7 @@
usart3: serial at fffcc000 {
compatible = "atmel,at91rm9200-usart";
reg = <0xfffcc000 0x200>;
- interrupts = <23 4 5>;
+ interrupts = <23 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
@@ -490,7 +495,7 @@
usb1: gadget at fffb0000 {
compatible = "atmel,at91rm9200-udc";
reg = <0xfffb0000 0x4000>;
- interrupts = <11 4 2>;
+ interrupts = <11 IRQ_TYPE_LEVEL_HIGH 2>;
status = "disabled";
};
};
@@ -515,7 +520,7 @@
usb0: ohci at 00300000 {
compatible = "atmel,at91rm9200-ohci", "usb-ohci";
reg = <0x00300000 0x100000>;
- interrupts = <23 4 2>;
+ interrupts = <23 IRQ_TYPE_LEVEL_HIGH 2>;
status = "disabled";
};
};
diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/at91sam9260.dtsi
index 7edadf3..a776f50 100644
--- a/arch/arm/boot/dts/at91sam9260.dtsi
+++ b/arch/arm/boot/dts/at91sam9260.dtsi
@@ -10,6 +10,7 @@
#include "skeleton.dtsi"
#include <dt-bindings/pinctrl/at91.h>
+#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
/ {
@@ -86,19 +87,23 @@
pit: timer at fffffd30 {
compatible = "atmel,at91sam9260-pit";
reg = <0xfffffd30 0xf>;
- interrupts = <1 4 7>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
};
tcb0: timer at fffa0000 {
compatible = "atmel,at91rm9200-tcb";
reg = <0xfffa0000 0x100>;
- interrupts = <17 4 0 18 4 0 19 4 0>;
+ interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0
+ 18 IRQ_TYPE_LEVEL_HIGH 0
+ 19 IRQ_TYPE_LEVEL_HIGH 0>;
};
tcb1: timer at fffdc000 {
compatible = "atmel,at91rm9200-tcb";
reg = <0xfffdc000 0x100>;
- interrupts = <26 4 0 27 4 0 28 4 0>;
+ interrupts = <26 IRQ_TYPE_LEVEL_HIGH 0
+ 27 IRQ_TYPE_LEVEL_HIGH 0
+ 28 IRQ_TYPE_LEVEL_HIGH 0>;
};
pinctrl at fffff400 {
@@ -345,7 +350,7 @@
pioA: gpio at fffff400 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x200>;
- interrupts = <2 4 1>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -355,7 +360,7 @@
pioB: gpio at fffff600 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff600 0x200>;
- interrupts = <3 4 1>;
+ interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -365,7 +370,7 @@
pioC: gpio at fffff800 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff800 0x200>;
- interrupts = <4 4 1>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -376,7 +381,7 @@
dbgu: serial at fffff200 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffff200 0x200>;
- interrupts = <1 4 7>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_dbgu>;
status = "disabled";
@@ -385,7 +390,7 @@
usart0: serial at fffb0000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffb0000 0x200>;
- interrupts = <6 4 5>;
+ interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
@@ -396,7 +401,7 @@
usart1: serial at fffb4000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffb4000 0x200>;
- interrupts = <7 4 5>;
+ interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
@@ -407,7 +412,7 @@
usart2: serial at fffb8000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffb8000 0x200>;
- interrupts = <8 4 5>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
@@ -418,7 +423,7 @@
usart3: serial at fffd0000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffd0000 0x200>;
- interrupts = <23 4 5>;
+ interrupts = <23 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
@@ -429,7 +434,7 @@
uart0: serial at fffd4000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffd4000 0x200>;
- interrupts = <24 4 5>;
+ interrupts = <24 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
@@ -440,7 +445,7 @@
uart1: serial at fffd8000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffd8000 0x200>;
- interrupts = <25 4 5>;
+ interrupts = <25 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
@@ -451,7 +456,7 @@
macb0: ethernet at fffc4000 {
compatible = "cdns,at32ap7000-macb", "cdns,macb";
reg = <0xfffc4000 0x100>;
- interrupts = <21 4 3>;
+ interrupts = <21 IRQ_TYPE_LEVEL_HIGH 3>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_macb_rmii>;
status = "disabled";
@@ -460,14 +465,14 @@
usb1: gadget at fffa4000 {
compatible = "atmel,at91rm9200-udc";
reg = <0xfffa4000 0x4000>;
- interrupts = <10 4 2>;
+ interrupts = <10 IRQ_TYPE_LEVEL_HIGH 2>;
status = "disabled";
};
i2c0: i2c at fffac000 {
compatible = "atmel,at91sam9260-i2c";
reg = <0xfffac000 0x100>;
- interrupts = <11 4 6>;
+ interrupts = <11 IRQ_TYPE_LEVEL_HIGH 6>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -476,7 +481,7 @@
mmc0: mmc at fffa8000 {
compatible = "atmel,hsmci";
reg = <0xfffa8000 0x600>;
- interrupts = <9 4 0>;
+ interrupts = <9 IRQ_TYPE_LEVEL_HIGH 0>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -485,7 +490,7 @@
ssc0: ssc at fffbc000 {
compatible = "atmel,at91rm9200-ssc";
reg = <0xfffbc000 0x4000>;
- interrupts = <14 4 5>;
+ interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
status = "disabled";
@@ -496,7 +501,7 @@
#size-cells = <0>;
compatible = "atmel,at91rm9200-spi";
reg = <0xfffc8000 0x200>;
- interrupts = <12 4 3>;
+ interrupts = <12 IRQ_TYPE_LEVEL_HIGH 3>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_spi0>;
status = "disabled";
@@ -507,7 +512,7 @@
#size-cells = <0>;
compatible = "atmel,at91rm9200-spi";
reg = <0xfffcc000 0x200>;
- interrupts = <13 4 3>;
+ interrupts = <13 IRQ_TYPE_LEVEL_HIGH 3>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_spi1>;
status = "disabled";
@@ -516,7 +521,7 @@
adc0: adc at fffe0000 {
compatible = "atmel,at91sam9260-adc";
reg = <0xfffe0000 0x100>;
- interrupts = <5 4 0>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 0>;
atmel,adc-use-external-triggers;
atmel,adc-channels-used = <0xf>;
atmel,adc-vref = <3300>;
@@ -579,7 +584,7 @@
usb0: ohci at 00500000 {
compatible = "atmel,at91rm9200-ohci", "usb-ohci";
reg = <0x00500000 0x100000>;
- interrupts = <20 4 2>;
+ interrupts = <20 IRQ_TYPE_LEVEL_HIGH 2>;
status = "disabled";
};
};
diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi
index bb4d7ca..d9cf51a 100644
--- a/arch/arm/boot/dts/at91sam9263.dtsi
+++ b/arch/arm/boot/dts/at91sam9263.dtsi
@@ -8,6 +8,7 @@
#include "skeleton.dtsi"
#include <dt-bindings/pinctrl/at91.h>
+#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
/ {
@@ -74,13 +75,13 @@
pit: timer at fffffd30 {
compatible = "atmel,at91sam9260-pit";
reg = <0xfffffd30 0xf>;
- interrupts = <1 4 7>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
};
tcb0: timer at fff7c000 {
compatible = "atmel,at91rm9200-tcb";
reg = <0xfff7c000 0x100>;
- interrupts = <19 4 0>;
+ interrupts = <19 IRQ_TYPE_LEVEL_HIGH 0>;
};
rstc at fffffd00 {
@@ -326,7 +327,7 @@
pioA: gpio at fffff200 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff200 0x200>;
- interrupts = <2 4 1>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -336,7 +337,7 @@
pioB: gpio at fffff400 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x200>;
- interrupts = <3 4 1>;
+ interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -346,7 +347,7 @@
pioC: gpio at fffff600 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff600 0x200>;
- interrupts = <4 4 1>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -356,7 +357,7 @@
pioD: gpio at fffff800 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff800 0x200>;
- interrupts = <4 4 1>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -366,7 +367,7 @@
pioE: gpio at fffffa00 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffffa00 0x200>;
- interrupts = <4 4 1>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -377,7 +378,7 @@
dbgu: serial at ffffee00 {
compatible = "atmel,at91sam9260-usart";
reg = <0xffffee00 0x200>;
- interrupts = <1 4 7>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_dbgu>;
status = "disabled";
@@ -386,7 +387,7 @@
usart0: serial at fff8c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfff8c000 0x200>;
- interrupts = <7 4 5>;
+ interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
@@ -397,7 +398,7 @@
usart1: serial at fff90000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfff90000 0x200>;
- interrupts = <8 4 5>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
@@ -408,7 +409,7 @@
usart2: serial at fff94000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfff94000 0x200>;
- interrupts = <9 4 5>;
+ interrupts = <9 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
@@ -419,7 +420,7 @@
ssc0: ssc at fff98000 {
compatible = "atmel,at91rm9200-ssc";
reg = <0xfff98000 0x4000>;
- interrupts = <16 4 5>;
+ interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
status = "disabled";
@@ -428,7 +429,7 @@
ssc1: ssc at fff9c000 {
compatible = "atmel,at91rm9200-ssc";
reg = <0xfff9c000 0x4000>;
- interrupts = <17 4 5>;
+ interrupts = <17 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>;
status = "disabled";
@@ -437,7 +438,7 @@
macb0: ethernet at fffbc000 {
compatible = "cdns,at32ap7000-macb", "cdns,macb";
reg = <0xfffbc000 0x100>;
- interrupts = <21 4 3>;
+ interrupts = <21 IRQ_TYPE_LEVEL_HIGH 3>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_macb_rmii>;
status = "disabled";
@@ -446,14 +447,14 @@
usb1: gadget at fff78000 {
compatible = "atmel,at91rm9200-udc";
reg = <0xfff78000 0x4000>;
- interrupts = <24 4 2>;
+ interrupts = <24 IRQ_TYPE_LEVEL_HIGH 2>;
status = "disabled";
};
i2c0: i2c at fff88000 {
compatible = "atmel,at91sam9263-i2c";
reg = <0xfff88000 0x100>;
- interrupts = <13 4 6>;
+ interrupts = <13 IRQ_TYPE_LEVEL_HIGH 6>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -462,7 +463,7 @@
mmc0: mmc at fff80000 {
compatible = "atmel,hsmci";
reg = <0xfff80000 0x600>;
- interrupts = <10 4 0>;
+ interrupts = <10 IRQ_TYPE_LEVEL_HIGH 0>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -471,7 +472,7 @@
mmc1: mmc at fff84000 {
compatible = "atmel,hsmci";
reg = <0xfff84000 0x600>;
- interrupts = <11 4 0>;
+ interrupts = <11 IRQ_TYPE_LEVEL_HIGH 0>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -488,7 +489,7 @@
#size-cells = <0>;
compatible = "atmel,at91rm9200-spi";
reg = <0xfffa4000 0x200>;
- interrupts = <14 4 3>;
+ interrupts = <14 IRQ_TYPE_LEVEL_HIGH 3>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_spi0>;
status = "disabled";
@@ -499,7 +500,7 @@
#size-cells = <0>;
compatible = "atmel,at91rm9200-spi";
reg = <0xfffa8000 0x200>;
- interrupts = <15 4 3>;
+ interrupts = <15 IRQ_TYPE_LEVEL_HIGH 3>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_spi1>;
status = "disabled";
@@ -527,7 +528,7 @@
usb0: ohci at 00a00000 {
compatible = "atmel,at91rm9200-ohci", "usb-ohci";
reg = <0x00a00000 0x100000>;
- interrupts = <29 4 2>;
+ interrupts = <29 IRQ_TYPE_LEVEL_HIGH 2>;
status = "disabled";
};
};
diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi
index 8ba4c71..f0091af 100644
--- a/arch/arm/boot/dts/at91sam9g45.dtsi
+++ b/arch/arm/boot/dts/at91sam9g45.dtsi
@@ -11,6 +11,7 @@
#include "skeleton.dtsi"
#include <dt-bindings/pinctrl/at91.h>
+#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
/ {
@@ -85,7 +86,7 @@
pit: timer at fffffd30 {
compatible = "atmel,at91sam9260-pit";
reg = <0xfffffd30 0xf>;
- interrupts = <1 4 7>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
};
@@ -97,19 +98,19 @@
tcb0: timer at fff7c000 {
compatible = "atmel,at91rm9200-tcb";
reg = <0xfff7c000 0x100>;
- interrupts = <18 4 0>;
+ interrupts = <18 IRQ_TYPE_LEVEL_HIGH 0>;
};
tcb1: timer at fffd4000 {
compatible = "atmel,at91rm9200-tcb";
reg = <0xfffd4000 0x100>;
- interrupts = <18 4 0>;
+ interrupts = <18 IRQ_TYPE_LEVEL_HIGH 0>;
};
dma: dma-controller at ffffec00 {
compatible = "atmel,at91sam9g45-dma";
reg = <0xffffec00 0x200>;
- interrupts = <21 4 0>;
+ interrupts = <21 IRQ_TYPE_LEVEL_HIGH 0>;
#dma-cells = <2>;
};
@@ -346,7 +347,7 @@
pioA: gpio at fffff200 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff200 0x200>;
- interrupts = <2 4 1>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -356,7 +357,7 @@
pioB: gpio at fffff400 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x200>;
- interrupts = <3 4 1>;
+ interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -366,7 +367,7 @@
pioC: gpio at fffff600 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff600 0x200>;
- interrupts = <4 4 1>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -376,7 +377,7 @@
pioD: gpio at fffff800 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff800 0x200>;
- interrupts = <5 4 1>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -386,7 +387,7 @@
pioE: gpio at fffffa00 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffffa00 0x200>;
- interrupts = <5 4 1>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -397,7 +398,7 @@
dbgu: serial at ffffee00 {
compatible = "atmel,at91sam9260-usart";
reg = <0xffffee00 0x200>;
- interrupts = <1 4 7>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_dbgu>;
status = "disabled";
@@ -406,7 +407,7 @@
usart0: serial at fff8c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfff8c000 0x200>;
- interrupts = <7 4 5>;
+ interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
@@ -417,7 +418,7 @@
usart1: serial at fff90000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfff90000 0x200>;
- interrupts = <8 4 5>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
@@ -428,7 +429,7 @@
usart2: serial at fff94000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfff94000 0x200>;
- interrupts = <9 4 5>;
+ interrupts = <9 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
@@ -439,7 +440,7 @@
usart3: serial at fff98000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfff98000 0x200>;
- interrupts = <10 4 5>;
+ interrupts = <10 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
@@ -450,7 +451,7 @@
macb0: ethernet at fffbc000 {
compatible = "cdns,at32ap7000-macb", "cdns,macb";
reg = <0xfffbc000 0x100>;
- interrupts = <25 4 3>;
+ interrupts = <25 IRQ_TYPE_LEVEL_HIGH 3>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_macb_rmii>;
status = "disabled";
@@ -459,7 +460,7 @@
i2c0: i2c at fff84000 {
compatible = "atmel,at91sam9g10-i2c";
reg = <0xfff84000 0x100>;
- interrupts = <12 4 6>;
+ interrupts = <12 IRQ_TYPE_LEVEL_HIGH 6>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -468,7 +469,7 @@
i2c1: i2c at fff88000 {
compatible = "atmel,at91sam9g10-i2c";
reg = <0xfff88000 0x100>;
- interrupts = <13 4 6>;
+ interrupts = <13 IRQ_TYPE_LEVEL_HIGH 6>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -477,7 +478,7 @@
ssc0: ssc at fff9c000 {
compatible = "atmel,at91sam9g45-ssc";
reg = <0xfff9c000 0x4000>;
- interrupts = <16 4 5>;
+ interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
status = "disabled";
@@ -486,7 +487,7 @@
ssc1: ssc at fffa0000 {
compatible = "atmel,at91sam9g45-ssc";
reg = <0xfffa0000 0x4000>;
- interrupts = <17 4 5>;
+ interrupts = <17 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>;
status = "disabled";
@@ -495,7 +496,7 @@
adc0: adc at fffb0000 {
compatible = "atmel,at91sam9260-adc";
reg = <0xfffb0000 0x100>;
- interrupts = <20 4 0>;
+ interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
atmel,adc-use-external-triggers;
atmel,adc-channels-used = <0xff>;
atmel,adc-vref = <3300>;
@@ -535,7 +536,7 @@
mmc0: mmc at fff80000 {
compatible = "atmel,hsmci";
reg = <0xfff80000 0x600>;
- interrupts = <11 4 0>;
+ interrupts = <11 IRQ_TYPE_LEVEL_HIGH 0>;
dmas = <&dma 1 0>;
dma-names = "rxtx";
#address-cells = <1>;
@@ -546,7 +547,7 @@
mmc1: mmc at fffd0000 {
compatible = "atmel,hsmci";
reg = <0xfffd0000 0x600>;
- interrupts = <29 4 0>;
+ interrupts = <29 IRQ_TYPE_LEVEL_HIGH 0>;
dmas = <&dma 1 13>;
dma-names = "rxtx";
#address-cells = <1>;
@@ -604,14 +605,14 @@
usb0: ohci at 00700000 {
compatible = "atmel,at91rm9200-ohci", "usb-ohci";
reg = <0x00700000 0x100000>;
- interrupts = <22 4 2>;
+ interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
status = "disabled";
};
usb1: ehci at 00800000 {
compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
reg = <0x00800000 0x100000>;
- interrupts = <22 4 2>;
+ interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
status = "disabled";
};
};
diff --git a/arch/arm/boot/dts/at91sam9n12.dtsi b/arch/arm/boot/dts/at91sam9n12.dtsi
index e166e0c..566af32 100644
--- a/arch/arm/boot/dts/at91sam9n12.dtsi
+++ b/arch/arm/boot/dts/at91sam9n12.dtsi
@@ -9,6 +9,7 @@
#include "skeleton.dtsi"
#include <dt-bindings/pinctrl/at91.h>
+#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
/ {
@@ -79,7 +80,7 @@
pit: timer at fffffe30 {
compatible = "atmel,at91sam9260-pit";
reg = <0xfffffe30 0xf>;
- interrupts = <1 4 7>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
};
shdwc at fffffe10 {
@@ -90,7 +91,7 @@
mmc0: mmc at f0008000 {
compatible = "atmel,hsmci";
reg = <0xf0008000 0x600>;
- interrupts = <12 4 0>;
+ interrupts = <12 IRQ_TYPE_LEVEL_HIGH 0>;
dmas = <&dma 1 0>;
dma-names = "rxtx";
#address-cells = <1>;
@@ -101,19 +102,19 @@
tcb0: timer at f8008000 {
compatible = "atmel,at91sam9x5-tcb";
reg = <0xf8008000 0x100>;
- interrupts = <17 4 0>;
+ interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
};
tcb1: timer at f800c000 {
compatible = "atmel,at91sam9x5-tcb";
reg = <0xf800c000 0x100>;
- interrupts = <17 4 0>;
+ interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
};
dma: dma-controller at ffffec00 {
compatible = "atmel,at91sam9g45-dma";
reg = <0xffffec00 0x200>;
- interrupts = <20 4 0>;
+ interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
#dma-cells = <2>;
};
@@ -287,7 +288,7 @@
pioA: gpio at fffff400 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x200>;
- interrupts = <2 4 1>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -297,7 +298,7 @@
pioB: gpio at fffff600 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff600 0x200>;
- interrupts = <2 4 1>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -307,7 +308,7 @@
pioC: gpio at fffff800 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff800 0x200>;
- interrupts = <3 4 1>;
+ interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -317,7 +318,7 @@
pioD: gpio at fffffa00 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffffa00 0x200>;
- interrupts = <3 4 1>;
+ interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -328,7 +329,7 @@
dbgu: serial at fffff200 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffff200 0x200>;
- interrupts = <1 4 7>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_dbgu>;
status = "disabled";
@@ -337,7 +338,7 @@
ssc0: ssc at f0010000 {
compatible = "atmel,at91sam9g45-ssc";
reg = <0xf0010000 0x4000>;
- interrupts = <28 4 5>;
+ interrupts = <28 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
status = "disabled";
@@ -346,7 +347,7 @@
usart0: serial at f801c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf801c000 0x4000>;
- interrupts = <5 4 5>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usart0>;
status = "disabled";
@@ -355,7 +356,7 @@
usart1: serial at f8020000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8020000 0x4000>;
- interrupts = <6 4 5>;
+ interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usart1>;
status = "disabled";
@@ -364,7 +365,7 @@
usart2: serial at f8024000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8024000 0x4000>;
- interrupts = <7 4 5>;
+ interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usart2>;
status = "disabled";
@@ -373,7 +374,7 @@
usart3: serial at f8028000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8028000 0x4000>;
- interrupts = <8 4 5>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usart3>;
status = "disabled";
@@ -382,7 +383,7 @@
i2c0: i2c at f8010000 {
compatible = "atmel,at91sam9x5-i2c";
reg = <0xf8010000 0x100>;
- interrupts = <9 4 6>;
+ interrupts = <9 IRQ_TYPE_LEVEL_HIGH 6>;
dmas = <&dma 1 13>,
<&dma 1 14>;
dma-names = "tx", "rx";
@@ -394,7 +395,7 @@
i2c1: i2c at f8014000 {
compatible = "atmel,at91sam9x5-i2c";
reg = <0xf8014000 0x100>;
- interrupts = <10 4 6>;
+ interrupts = <10 IRQ_TYPE_LEVEL_HIGH 6>;
dmas = <&dma 1 15>,
<&dma 1 16>;
dma-names = "tx", "rx";
@@ -408,7 +409,7 @@
#size-cells = <0>;
compatible = "atmel,at91rm9200-spi";
reg = <0xf0000000 0x100>;
- interrupts = <13 4 3>;
+ interrupts = <13 IRQ_TYPE_LEVEL_HIGH 3>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_spi0>;
status = "disabled";
@@ -419,7 +420,7 @@
#size-cells = <0>;
compatible = "atmel,at91rm9200-spi";
reg = <0xf0004000 0x100>;
- interrupts = <14 4 3>;
+ interrupts = <14 IRQ_TYPE_LEVEL_HIGH 3>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_spi1>;
status = "disabled";
@@ -450,7 +451,7 @@
usb0: ohci at 00500000 {
compatible = "atmel,at91rm9200-ohci", "usb-ohci";
reg = <0x00500000 0x00100000>;
- interrupts = <22 4 2>;
+ interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
status = "disabled";
};
};
diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi
index cfbf923..af91599 100644
--- a/arch/arm/boot/dts/at91sam9x5.dtsi
+++ b/arch/arm/boot/dts/at91sam9x5.dtsi
@@ -11,6 +11,7 @@
#include "skeleton.dtsi"
#include <dt-bindings/pinctrl/at91.h>
+#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
/ {
@@ -87,32 +88,32 @@
pit: timer at fffffe30 {
compatible = "atmel,at91sam9260-pit";
reg = <0xfffffe30 0xf>;
- interrupts = <1 4 7>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
};
tcb0: timer at f8008000 {
compatible = "atmel,at91sam9x5-tcb";
reg = <0xf8008000 0x100>;
- interrupts = <17 4 0>;
+ interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
};
tcb1: timer at f800c000 {
compatible = "atmel,at91sam9x5-tcb";
reg = <0xf800c000 0x100>;
- interrupts = <17 4 0>;
+ interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
};
dma0: dma-controller at ffffec00 {
compatible = "atmel,at91sam9g45-dma";
reg = <0xffffec00 0x200>;
- interrupts = <20 4 0>;
+ interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
#dma-cells = <2>;
};
dma1: dma-controller at ffffee00 {
compatible = "atmel,at91sam9g45-dma";
reg = <0xffffee00 0x200>;
- interrupts = <21 4 0>;
+ interrupts = <21 IRQ_TYPE_LEVEL_HIGH 0>;
#dma-cells = <2>;
};
@@ -416,7 +417,7 @@
pioA: gpio at fffff400 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x200>;
- interrupts = <2 4 1>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -426,7 +427,7 @@
pioB: gpio at fffff600 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff600 0x200>;
- interrupts = <2 4 1>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
#gpio-lines = <19>;
@@ -437,7 +438,7 @@
pioC: gpio at fffff800 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff800 0x200>;
- interrupts = <3 4 1>;
+ interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -447,7 +448,7 @@
pioD: gpio at fffffa00 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffffa00 0x200>;
- interrupts = <3 4 1>;
+ interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
#gpio-lines = <22>;
@@ -459,7 +460,7 @@
ssc0: ssc at f0010000 {
compatible = "atmel,at91sam9g45-ssc";
reg = <0xf0010000 0x4000>;
- interrupts = <28 4 5>;
+ interrupts = <28 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
status = "disabled";
@@ -468,7 +469,7 @@
mmc0: mmc at f0008000 {
compatible = "atmel,hsmci";
reg = <0xf0008000 0x600>;
- interrupts = <12 4 0>;
+ interrupts = <12 IRQ_TYPE_LEVEL_HIGH 0>;
dmas = <&dma0 1 0>;
dma-names = "rxtx";
#address-cells = <1>;
@@ -479,7 +480,7 @@
mmc1: mmc at f000c000 {
compatible = "atmel,hsmci";
reg = <0xf000c000 0x600>;
- interrupts = <26 4 0>;
+ interrupts = <26 IRQ_TYPE_LEVEL_HIGH 0>;
dmas = <&dma1 1 0>;
dma-names = "rxtx";
#address-cells = <1>;
@@ -490,7 +491,7 @@
dbgu: serial at fffff200 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffff200 0x200>;
- interrupts = <1 4 7>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_dbgu>;
status = "disabled";
@@ -499,7 +500,7 @@
usart0: serial at f801c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf801c000 0x200>;
- interrupts = <5 4 5>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usart0>;
status = "disabled";
@@ -508,7 +509,7 @@
usart1: serial at f8020000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8020000 0x200>;
- interrupts = <6 4 5>;
+ interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usart1>;
status = "disabled";
@@ -517,7 +518,7 @@
usart2: serial at f8024000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8024000 0x200>;
- interrupts = <7 4 5>;
+ interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usart2>;
status = "disabled";
@@ -526,7 +527,7 @@
macb0: ethernet at f802c000 {
compatible = "cdns,at32ap7000-macb", "cdns,macb";
reg = <0xf802c000 0x100>;
- interrupts = <24 4 3>;
+ interrupts = <24 IRQ_TYPE_LEVEL_HIGH 3>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_macb0_rmii>;
status = "disabled";
@@ -535,14 +536,14 @@
macb1: ethernet at f8030000 {
compatible = "cdns,at32ap7000-macb", "cdns,macb";
reg = <0xf8030000 0x100>;
- interrupts = <27 4 3>;
+ interrupts = <27 IRQ_TYPE_LEVEL_HIGH 3>;
status = "disabled";
};
i2c0: i2c at f8010000 {
compatible = "atmel,at91sam9x5-i2c";
reg = <0xf8010000 0x100>;
- interrupts = <9 4 6>;
+ interrupts = <9 IRQ_TYPE_LEVEL_HIGH 6>;
dmas = <&dma0 1 7>,
<&dma0 1 8>;
dma-names = "tx", "rx";
@@ -556,7 +557,7 @@
i2c1: i2c at f8014000 {
compatible = "atmel,at91sam9x5-i2c";
reg = <0xf8014000 0x100>;
- interrupts = <10 4 6>;
+ interrupts = <10 IRQ_TYPE_LEVEL_HIGH 6>;
dmas = <&dma1 1 5>,
<&dma1 1 6>;
dma-names = "tx", "rx";
@@ -570,7 +571,7 @@
i2c2: i2c at f8018000 {
compatible = "atmel,at91sam9x5-i2c";
reg = <0xf8018000 0x100>;
- interrupts = <11 4 6>;
+ interrupts = <11 IRQ_TYPE_LEVEL_HIGH 6>;
dmas = <&dma0 1 9>,
<&dma0 1 10>;
dma-names = "tx", "rx";
@@ -584,7 +585,7 @@
adc0: adc at f804c000 {
compatible = "atmel,at91sam9260-adc";
reg = <0xf804c000 0x100>;
- interrupts = <19 4 0>;
+ interrupts = <19 IRQ_TYPE_LEVEL_HIGH 0>;
atmel,adc-use-external;
atmel,adc-channels-used = <0xffff>;
atmel,adc-vref = <3300>;
@@ -627,7 +628,7 @@
#size-cells = <0>;
compatible = "atmel,at91rm9200-spi";
reg = <0xf0000000 0x100>;
- interrupts = <13 4 3>;
+ interrupts = <13 IRQ_TYPE_LEVEL_HIGH 3>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_spi0>;
status = "disabled";
@@ -638,7 +639,7 @@
#size-cells = <0>;
compatible = "atmel,at91rm9200-spi";
reg = <0xf0004000 0x100>;
- interrupts = <14 4 3>;
+ interrupts = <14 IRQ_TYPE_LEVEL_HIGH 3>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_spi1>;
status = "disabled";
@@ -647,7 +648,7 @@
rtc at fffffeb0 {
compatible = "atmel,at91rm9200-rtc";
reg = <0xfffffeb0 0x40>;
- interrupts = <1 4 7>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
status = "disabled";
};
};
@@ -676,14 +677,14 @@
usb0: ohci at 00600000 {
compatible = "atmel,at91rm9200-ohci", "usb-ohci";
reg = <0x00600000 0x100000>;
- interrupts = <22 4 2>;
+ interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
status = "disabled";
};
usb1: ehci at 00700000 {
compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
reg = <0x00700000 0x100000>;
- interrupts = <22 4 2>;
+ interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
status = "disabled";
};
};
diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi
index 05a3380..c00e158 100644
--- a/arch/arm/boot/dts/sama5d3.dtsi
+++ b/arch/arm/boot/dts/sama5d3.dtsi
@@ -10,6 +10,7 @@
#include "skeleton.dtsi"
#include <dt-bindings/pinctrl/at91.h>
+#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
/ {
@@ -61,7 +62,7 @@
mmc0: mmc at f0000000 {
compatible = "atmel,hsmci";
reg = <0xf0000000 0x600>;
- interrupts = <21 4 0>;
+ interrupts = <21 IRQ_TYPE_LEVEL_HIGH 0>;
dmas = <&dma0 2 0>;
dma-names = "rxtx";
pinctrl-names = "default";
@@ -76,7 +77,7 @@
#size-cells = <0>;
compatible = "atmel,at91sam9x5-spi";
reg = <0xf0004000 0x100>;
- interrupts = <24 4 3>;
+ interrupts = <24 IRQ_TYPE_LEVEL_HIGH 3>;
cs-gpios = <&pioD 13 0
&pioD 14 0 /* conflicts with SCK0 and CANRX0 */
&pioD 15 0 /* conflicts with CTS0 and CANTX0 */
@@ -90,7 +91,7 @@
ssc0: ssc at f0008000 {
compatible = "atmel,at91sam9g45-ssc";
reg = <0xf0008000 0x4000>;
- interrupts = <38 4 4>;
+ interrupts = <38 IRQ_TYPE_LEVEL_HIGH 4>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
status = "disabled";
@@ -99,7 +100,7 @@
can0: can at f000c000 {
compatible = "atmel,at91sam9x5-can";
reg = <0xf000c000 0x300>;
- interrupts = <40 4 3>;
+ interrupts = <40 IRQ_TYPE_LEVEL_HIGH 3>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_can0_rx_tx>;
status = "disabled";
@@ -108,13 +109,13 @@
tcb0: timer at f0010000 {
compatible = "atmel,at91sam9x5-tcb";
reg = <0xf0010000 0x100>;
- interrupts = <26 4 0>;
+ interrupts = <26 IRQ_TYPE_LEVEL_HIGH 0>;
};
i2c0: i2c at f0014000 {
compatible = "atmel,at91sam9x5-i2c";
reg = <0xf0014000 0x4000>;
- interrupts = <18 4 6>;
+ interrupts = <18 IRQ_TYPE_LEVEL_HIGH 6>;
dmas = <&dma0 2 7>,
<&dma0 2 8>;
dma-names = "tx", "rx";
@@ -128,7 +129,7 @@
i2c1: i2c at f0018000 {
compatible = "atmel,at91sam9x5-i2c";
reg = <0xf0018000 0x4000>;
- interrupts = <19 4 6>;
+ interrupts = <19 IRQ_TYPE_LEVEL_HIGH 6>;
dmas = <&dma0 2 9>,
<&dma0 2 10>;
dma-names = "tx", "rx";
@@ -142,7 +143,7 @@
usart0: serial at f001c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf001c000 0x100>;
- interrupts = <12 4 5>;
+ interrupts = <12 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usart0>;
status = "disabled";
@@ -151,7 +152,7 @@
usart1: serial at f0020000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf0020000 0x100>;
- interrupts = <13 4 5>;
+ interrupts = <13 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usart1>;
status = "disabled";
@@ -160,7 +161,7 @@
macb0: ethernet at f0028000 {
compatible = "cnds,pc302-gem", "cdns,gem";
reg = <0xf0028000 0x100>;
- interrupts = <34 4 3>;
+ interrupts = <34 IRQ_TYPE_LEVEL_HIGH 3>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_macb0_data_rgmii &pinctrl_macb0_signal_rgmii>;
status = "disabled";
@@ -169,14 +170,14 @@
isi: isi at f0034000 {
compatible = "atmel,at91sam9g45-isi";
reg = <0xf0034000 0x4000>;
- interrupts = <37 4 5>;
+ interrupts = <37 IRQ_TYPE_LEVEL_HIGH 5>;
status = "disabled";
};
mmc1: mmc at f8000000 {
compatible = "atmel,hsmci";
reg = <0xf8000000 0x600>;
- interrupts = <22 4 0>;
+ interrupts = <22 IRQ_TYPE_LEVEL_HIGH 0>;
dmas = <&dma1 2 0>;
dma-names = "rxtx";
pinctrl-names = "default";
@@ -189,7 +190,7 @@
mmc2: mmc at f8004000 {
compatible = "atmel,hsmci";
reg = <0xf8004000 0x600>;
- interrupts = <23 4 0>;
+ interrupts = <23 IRQ_TYPE_LEVEL_HIGH 0>;
dmas = <&dma1 2 1>;
dma-names = "rxtx";
pinctrl-names = "default";
@@ -204,7 +205,7 @@
#size-cells = <0>;
compatible = "atmel,at91sam9x5-spi";
reg = <0xf8008000 0x100>;
- interrupts = <25 4 3>;
+ interrupts = <25 IRQ_TYPE_LEVEL_HIGH 3>;
cs-gpios = <&pioC 25 0
&pioC 26 0 /* conflitcs with TWD1 and ISI_D11 */
&pioC 27 0 /* conflitcs with TWCK1 and ISI_D10 */
@@ -218,7 +219,7 @@
ssc1: ssc at f800c000 {
compatible = "atmel,at91sam9g45-ssc";
reg = <0xf800c000 0x4000>;
- interrupts = <39 4 4>;
+ interrupts = <39 IRQ_TYPE_LEVEL_HIGH 4>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>;
status = "disabled";
@@ -227,7 +228,7 @@
can1: can at f8010000 {
compatible = "atmel,at91sam9x5-can";
reg = <0xf8010000 0x300>;
- interrupts = <41 4 3>;
+ interrupts = <41 IRQ_TYPE_LEVEL_HIGH 3>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_can1_rx_tx>;
};
@@ -235,13 +236,13 @@
tcb1: timer at f8014000 {
compatible = "atmel,at91sam9x5-tcb";
reg = <0xf8014000 0x100>;
- interrupts = <27 4 0>;
+ interrupts = <27 IRQ_TYPE_LEVEL_HIGH 0>;
};
adc0: adc at f8018000 {
compatible = "atmel,at91sam9260-adc";
reg = <0xf8018000 0x100>;
- interrupts = <29 4 5>;
+ interrupts = <29 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <
&pinctrl_adc0_adtrg
@@ -295,7 +296,7 @@
tsadcc: tsadcc at f8018000 {
compatible = "atmel,at91sam9x5-tsadcc";
reg = <0xf8018000 0x4000>;
- interrupts = <29 4 5>;
+ interrupts = <29 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,tsadcc_clock = <300000>;
atmel,filtering_average = <0x03>;
atmel,pendet_debounce = <0x08>;
@@ -307,7 +308,7 @@
i2c2: i2c at f801c000 {
compatible = "atmel,at91sam9x5-i2c";
reg = <0xf801c000 0x4000>;
- interrupts = <20 4 6>;
+ interrupts = <20 IRQ_TYPE_LEVEL_HIGH 6>;
dmas = <&dma1 2 11>,
<&dma1 2 12>;
dma-names = "tx", "rx";
@@ -319,7 +320,7 @@
usart2: serial at f8020000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8020000 0x100>;
- interrupts = <14 4 5>;
+ interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usart2>;
status = "disabled";
@@ -328,7 +329,7 @@
usart3: serial at f8024000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8024000 0x100>;
- interrupts = <15 4 5>;
+ interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usart3>;
status = "disabled";
@@ -337,7 +338,7 @@
macb1: ethernet at f802c000 {
compatible = "cdns,at32ap7000-macb", "cdns,macb";
reg = <0xf802c000 0x100>;
- interrupts = <35 4 3>;
+ interrupts = <35 IRQ_TYPE_LEVEL_HIGH 3>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_macb1_rmii>;
status = "disabled";
@@ -346,7 +347,7 @@
sha at f8034000 {
compatible = "atmel,sam9g46-sha";
reg = <0xf8034000 0x100>;
- interrupts = <42 4 0>;
+ interrupts = <42 IRQ_TYPE_LEVEL_HIGH 0>;
};
aes at f8038000 {
@@ -358,20 +359,20 @@
tdes at f803c000 {
compatible = "atmel,sam9g46-tdes";
reg = <0xf803c000 0x100>;
- interrupts = <44 4 0>;
+ interrupts = <44 IRQ_TYPE_LEVEL_HIGH 0>;
};
dma0: dma-controller at ffffe600 {
compatible = "atmel,at91sam9g45-dma";
reg = <0xffffe600 0x200>;
- interrupts = <30 4 0>;
+ interrupts = <30 IRQ_TYPE_LEVEL_HIGH 0>;
#dma-cells = <2>;
};
dma1: dma-controller at ffffe800 {
compatible = "atmel,at91sam9g45-dma";
reg = <0xffffe800 0x200>;
- interrupts = <31 4 0>;
+ interrupts = <31 IRQ_TYPE_LEVEL_HIGH 0>;
#dma-cells = <2>;
};
@@ -383,7 +384,7 @@
dbgu: serial at ffffee00 {
compatible = "atmel,at91sam9260-usart";
reg = <0xffffee00 0x200>;
- interrupts = <2 4 7>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH 7>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_dbgu>;
status = "disabled";
@@ -817,7 +818,7 @@
pioA: gpio at fffff200 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff200 0x100>;
- interrupts = <6 4 1>;
+ interrupts = <6 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -827,7 +828,7 @@
pioB: gpio at fffff400 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x100>;
- interrupts = <7 4 1>;
+ interrupts = <7 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -837,7 +838,7 @@
pioC: gpio at fffff600 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff600 0x100>;
- interrupts = <8 4 1>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -847,7 +848,7 @@
pioD: gpio at fffff800 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff800 0x100>;
- interrupts = <9 4 1>;
+ interrupts = <9 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -857,7 +858,7 @@
pioE: gpio at fffffa00 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffffa00 0x100>;
- interrupts = <10 4 1>;
+ interrupts = <10 IRQ_TYPE_LEVEL_HIGH 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
@@ -878,7 +879,7 @@
pit: timer at fffffe30 {
compatible = "atmel,at91sam9260-pit";
reg = <0xfffffe30 0xf>;
- interrupts = <3 4 5>;
+ interrupts = <3 IRQ_TYPE_LEVEL_HIGH 5>;
};
watchdog at fffffe40 {
@@ -890,7 +891,7 @@
rtc at fffffeb0 {
compatible = "atmel,at91rm9200-rtc";
reg = <0xfffffeb0 0x30>;
- interrupts = <1 4 7>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
};
};
@@ -900,7 +901,7 @@
compatible = "atmel,at91sam9rl-udc";
reg = <0x00500000 0x100000
0xf8030000 0x4000>;
- interrupts = <33 4 2>;
+ interrupts = <33 IRQ_TYPE_LEVEL_HIGH 2>;
status = "disabled";
ep0 {
@@ -1012,14 +1013,14 @@
usb1: ohci at 00600000 {
compatible = "atmel,at91rm9200-ohci", "usb-ohci";
reg = <0x00600000 0x100000>;
- interrupts = <32 4 2>;
+ interrupts = <32 IRQ_TYPE_LEVEL_HIGH 2>;
status = "disabled";
};
usb2: ehci at 00700000 {
compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
reg = <0x00700000 0x100000>;
- interrupts = <32 4 2>;
+ interrupts = <32 IRQ_TYPE_LEVEL_HIGH 2>;
status = "disabled";
};
@@ -1035,7 +1036,7 @@
0xffffc000 0x00000070 /* NFC HSMC regs */
0x00200000 0x00100000 /* NFC SRAM banks */
>;
- interrupts = <5 4 6>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 6>;
atmel,nand-addr-offset = <21>;
atmel,nand-cmd-offset = <22>;
pinctrl-names = "default";
--
1.7.10.4
More information about the linux-arm-kernel
mailing list