[PATCH 1/2] clk: sun5i: Add compatibles for Allwinner A13
Mike Turquette
mturquette at linaro.org
Tue May 14 15:26:02 EDT 2013
Quoting Emilio López (2013-04-30 04:20:23)
> Hi Maxime,
>
> El 30/04/13 06:56, Maxime Ripard escribió:
> > The A13 has a lot less clocks than the one found in the Allwinner A10.
> > Add these stripped down clocks to the clock driver and in the
> > documentation.
> >
> > Signed-off-by: Maxime Ripard <maxime.ripard at free-electrons.com>
>
> This patch looks good to me.
>
> Acked-by: Emilio López <emilio at elopez.com.ar>
>
I've taken patch #1 into clk-next.
Thanks!
Mike
> > ---
> > Documentation/devicetree/bindings/clock/sunxi.txt | 117 +++------------------
> > .../bindings/clock/sunxi/sun4i-a10-gates.txt | 93 ++++++++++++++++
> > .../bindings/clock/sunxi/sun5i-a13-gates.txt | 58 ++++++++++
> > drivers/clk/sunxi/clk-sunxi.c | 31 ++++--
> > 4 files changed, 187 insertions(+), 112 deletions(-)
> > create mode 100644 Documentation/devicetree/bindings/clock/sunxi/sun4i-a10-gates.txt
> > create mode 100644 Documentation/devicetree/bindings/clock/sunxi/sun5i-a13-gates.txt
> >
> > diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
> > index 729f524..d495521 100644
> > --- a/Documentation/devicetree/bindings/clock/sunxi.txt
> > +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
> > @@ -12,22 +12,30 @@ Required properties:
> > "allwinner,sun4i-axi-clk" - for the AXI clock
> > "allwinner,sun4i-axi-gates-clk" - for the AXI gates
> > "allwinner,sun4i-ahb-clk" - for the AHB clock
> > - "allwinner,sun4i-ahb-gates-clk" - for the AHB gates
> > + "allwinner,sun4i-ahb-gates-clk" - for the AHB gates on A10
> > + "allwinner,sun5i-a13-ahb-gates-clk" - for the AHB gates on A13
> > "allwinner,sun4i-apb0-clk" - for the APB0 clock
> > - "allwinner,sun4i-apb0-gates-clk" - for the APB0 gates
> > + "allwinner,sun4i-apb0-gates-clk" - for the APB0 gates on A10
> > + "allwinner,sun5i-a13-apb0-gates-clk" - for the APB0 gates on A13
> > "allwinner,sun4i-apb1-clk" - for the APB1 clock
> > "allwinner,sun4i-apb1-mux-clk" - for the APB1 clock muxing
> > - "allwinner,sun4i-apb1-gates-clk" - for the APB1 gates
> > + "allwinner,sun4i-apb1-gates-clk" - for the APB1 gates on A10
> > + "allwinner,sun5i-a13-apb1-gates-clk" - for the APB1 gates on A13
> >
> > Required properties for all clocks:
> > - reg : shall be the control register address for the clock.
> > - clocks : shall be the input parent clock(s) phandle for the clock
> > - #clock-cells : from common clock binding; shall be set to 0 except for
> > - "allwinner,sun4i-*-gates-clk" where it shall be set to 1
> > + "allwinner,*-gates-clk" where it shall be set to 1
> >
> > -Additionally, "allwinner,sun4i-*-gates-clk" clocks require:
> > +Additionally, "allwinner,*-gates-clk" clocks require:
> > - clock-output-names : the corresponding gate names that the clock controls
> >
> > +Clock consumers should specify the desired clocks they use with a
> > +"clocks" phandle cell. Consumers that are using a gated clock should
> > +provide an additional ID in their clock property. The values of this
> > +ID are documented in sunxi/<soc>-gates.txt.
> > +
> > For example:
> >
> > osc24M: osc24M at 01c20050 {
> > @@ -50,102 +58,3 @@ cpu: cpu at 01c20054 {
> > reg = <0x01c20054 0x4>;
> > clocks = <&osc32k>, <&osc24M>, <&pll1>;
> > };
> > -
> > -
> > -
> > -Gate clock outputs
> > -
> > -The "allwinner,sun4i-*-gates-clk" clocks provide several gatable outputs;
> > -their corresponding offsets as present on sun4i are listed below. Note that
> > -some of these gates are not present on sun5i.
> > -
> > - * AXI gates ("allwinner,sun4i-axi-gates-clk")
> > -
> > - DRAM 0
> > -
> > - * AHB gates ("allwinner,sun4i-ahb-gates-clk")
> > -
> > - USB0 0
> > - EHCI0 1
> > - OHCI0 2*
> > - EHCI1 3
> > - OHCI1 4*
> > - SS 5
> > - DMA 6
> > - BIST 7
> > - MMC0 8
> > - MMC1 9
> > - MMC2 10
> > - MMC3 11
> > - MS 12**
> > - NAND 13
> > - SDRAM 14
> > -
> > - ACE 16
> > - EMAC 17
> > - TS 18
> > -
> > - SPI0 20
> > - SPI1 21
> > - SPI2 22
> > - SPI3 23
> > - PATA 24
> > - SATA 25**
> > - GPS 26*
> > -
> > - VE 32
> > - TVD 33
> > - TVE0 34
> > - TVE1 35
> > - LCD0 36
> > - LCD1 37
> > -
> > - CSI0 40
> > - CSI1 41
> > -
> > - HDMI 43
> > - DE_BE0 44
> > - DE_BE1 45
> > - DE_FE0 46
> > - DE_FE1 47
> > -
> > - MP 50
> > -
> > - MALI400 52
> > -
> > - * APB0 gates ("allwinner,sun4i-apb0-gates-clk")
> > -
> > - CODEC 0
> > - SPDIF 1*
> > - AC97 2
> > - IIS 3
> > -
> > - PIO 5
> > - IR0 6
> > - IR1 7
> > -
> > - KEYPAD 10
> > -
> > - * APB1 gates ("allwinner,sun4i-apb1-gates-clk")
> > -
> > - I2C0 0
> > - I2C1 1
> > - I2C2 2
> > -
> > - CAN 4
> > - SCR 5
> > - PS20 6
> > - PS21 7
> > -
> > - UART0 16
> > - UART1 17
> > - UART2 18
> > - UART3 19
> > - UART4 20
> > - UART5 21
> > - UART6 22
> > - UART7 23
> > -
> > -Notation:
> > - [*]: The datasheet didn't mention these, but they are present on AW code
> > - [**]: The datasheet had this marked as "NC" but they are used on AW code
> > diff --git a/Documentation/devicetree/bindings/clock/sunxi/sun4i-a10-gates.txt b/Documentation/devicetree/bindings/clock/sunxi/sun4i-a10-gates.txt
> > new file mode 100644
> > index 0000000..6a03475
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/clock/sunxi/sun4i-a10-gates.txt
> > @@ -0,0 +1,93 @@
> > +Gate clock outputs
> > +------------------
> > +
> > + * AXI gates ("allwinner,sun4i-axi-gates-clk")
> > +
> > + DRAM 0
> > +
> > + * AHB gates ("allwinner,sun4i-ahb-gates-clk")
> > +
> > + USB0 0
> > + EHCI0 1
> > + OHCI0 2*
> > + EHCI1 3
> > + OHCI1 4*
> > + SS 5
> > + DMA 6
> > + BIST 7
> > + MMC0 8
> > + MMC1 9
> > + MMC2 10
> > + MMC3 11
> > + MS 12**
> > + NAND 13
> > + SDRAM 14
> > +
> > + ACE 16
> > + EMAC 17
> > + TS 18
> > +
> > + SPI0 20
> > + SPI1 21
> > + SPI2 22
> > + SPI3 23
> > + PATA 24
> > + SATA 25**
> > + GPS 26*
> > +
> > + VE 32
> > + TVD 33
> > + TVE0 34
> > + TVE1 35
> > + LCD0 36
> > + LCD1 37
> > +
> > + CSI0 40
> > + CSI1 41
> > +
> > + HDMI 43
> > + DE_BE0 44
> > + DE_BE1 45
> > + DE_FE1 46
> > + DE_FE1 47
> > +
> > + MP 50
> > +
> > + MALI400 52
> > +
> > + * APB0 gates ("allwinner,sun4i-apb0-gates-clk")
> > +
> > + CODEC 0
> > + SPDIF 1*
> > + AC97 2
> > + IIS 3
> > +
> > + PIO 5
> > + IR0 6
> > + IR1 7
> > +
> > + KEYPAD 10
> > +
> > + * APB1 gates ("allwinner,sun4i-apb1-gates-clk")
> > +
> > + I2C0 0
> > + I2C1 1
> > + I2C2 2
> > +
> > + CAN 4
> > + SCR 5
> > + PS20 6
> > + PS21 7
> > +
> > + UART0 16
> > + UART1 17
> > + UART2 18
> > + UART3 19
> > + UART4 20
> > + UART5 21
> > + UART6 22
> > + UART7 23
> > +
> > +Notation:
> > + [*]: The datasheet didn't mention these, but they are present on AW code
> > + [**]: The datasheet had this marked as "NC" but they are used on AW code
> > diff --git a/Documentation/devicetree/bindings/clock/sunxi/sun5i-a13-gates.txt b/Documentation/devicetree/bindings/clock/sunxi/sun5i-a13-gates.txt
> > new file mode 100644
> > index 0000000..006b6df
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/clock/sunxi/sun5i-a13-gates.txt
> > @@ -0,0 +1,58 @@
> > +Gate clock outputs
> > +------------------
> > +
> > + * AXI gates ("allwinner,sun4i-axi-gates-clk")
> > +
> > + DRAM 0
> > +
> > + * AHB gates ("allwinner,sun5i-a13-ahb-gates-clk")
> > +
> > + USBOTG 0
> > + EHCI 1
> > + OHCI 2
> > +
> > + SS 5
> > + DMA 6
> > + BIST 7
> > + MMC0 8
> > + MMC1 9
> > + MMC2 10
> > +
> > + NAND 13
> > + SDRAM 14
> > +
> > + SPI0 20
> > + SPI1 21
> > + SPI2 22
> > +
> > + STIMER 28
> > +
> > + VE 32
> > +
> > + LCD 36
> > +
> > + CSI 40
> > +
> > + DE_BE 44
> > +
> > + DE_FE 46
> > +
> > + IEP 51
> > + MALI400 52
> > +
> > + * APB0 gates ("allwinner,sun5i-a13-apb0-gates-clk")
> > +
> > + CODEC 0
> > +
> > + PIO 5
> > + IR 6
> > +
> > + * APB1 gates ("allwinner,sun5i-a13-apb1-gates-clk")
> > +
> > + I2C0 0
> > + I2C1 1
> > + I2C2 2
> > +
> > + UART1 17
> > +
> > + UART3 19
> > diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
> > index 8492ad1..930d36f 100644
> > --- a/drivers/clk/sunxi/clk-sunxi.c
> > +++ b/drivers/clk/sunxi/clk-sunxi.c
> > @@ -333,22 +333,34 @@ struct gates_data {
> > DECLARE_BITMAP(mask, SUNXI_GATES_MAX_SIZE);
> > };
> >
> > -static const __initconst struct gates_data axi_gates_data = {
> > +static const __initconst struct gates_data sun4i_axi_gates_data = {
> > .mask = {1},
> > };
> >
> > -static const __initconst struct gates_data ahb_gates_data = {
> > +static const __initconst struct gates_data sun4i_ahb_gates_data = {
> > .mask = {0x7F77FFF, 0x14FB3F},
> > };
> >
> > -static const __initconst struct gates_data apb0_gates_data = {
> > +static const __initconst struct gates_data sun5i_a13_ahb_gates_data = {
> > + .mask = {0x107067e7, 0x185111},
>
> If you send a v2 please use uppercase e and a below for consistency.
>
> > +};
> > +
> > +static const __initconst struct gates_data sun4i_apb0_gates_data = {
> > .mask = {0x4EF},
> > };
> >
> > -static const __initconst struct gates_data apb1_gates_data = {
> > +static const __initconst struct gates_data sun5i_a13_apb0_gates_data = {
> > + .mask = {0x61},
> > +};
> > +
> > +static const __initconst struct gates_data sun4i_apb1_gates_data = {
> > .mask = {0xFF00F7},
> > };
> >
> > +static const __initconst struct gates_data sun5i_a13_apb1_gates_data = {
> > + .mask = {0xa0007},
>
> > +};
> > +
> > static void __init sunxi_gates_clk_setup(struct device_node *node,
> > struct gates_data *data)
> > {
> > @@ -428,10 +440,13 @@ static const __initconst struct of_device_id clk_mux_match[] = {
> >
> > /* Matches for gate clocks */
> > static const __initconst struct of_device_id clk_gates_match[] = {
> > - {.compatible = "allwinner,sun4i-axi-gates-clk", .data = &axi_gates_data,},
> > - {.compatible = "allwinner,sun4i-ahb-gates-clk", .data = &ahb_gates_data,},
> > - {.compatible = "allwinner,sun4i-apb0-gates-clk", .data = &apb0_gates_data,},
> > - {.compatible = "allwinner,sun4i-apb1-gates-clk", .data = &apb1_gates_data,},
> > + {.compatible = "allwinner,sun4i-axi-gates-clk", .data = &sun4i_axi_gates_data,},
> > + {.compatible = "allwinner,sun4i-ahb-gates-clk", .data = &sun4i_ahb_gates_data,},
> > + {.compatible = "allwinner,sun5i-a13-ahb-gates-clk", .data = &sun5i_a13_ahb_gates_data,},
> > + {.compatible = "allwinner,sun4i-apb0-gates-clk", .data = &sun4i_apb0_gates_data,},
> > + {.compatible = "allwinner,sun5i-a13-apb0-gates-clk", .data = &sun5i_a13_apb0_gates_data,},
> > + {.compatible = "allwinner,sun4i-apb1-gates-clk", .data = &sun4i_apb1_gates_data,},
> > + {.compatible = "allwinner,sun5i-a13-apb1-gates-clk", .data = &sun5i_a13_apb1_gates_data,},
> > {}
> > };
> >
> >
>
> Thanks!
>
> Emilio
More information about the linux-arm-kernel
mailing list