[RFC][BUG] arm/dts: OMAP3: set #interrupt-cells to two

Javier Martinez Canillas martinez.javier at gmail.com
Sat Mar 30 09:18:19 EDT 2013


On Sat, Mar 30, 2013 at 9:21 AM, Christoph Fritz
<chf.fritz at googlemail.com> wrote:
> This patch sets gpio #interrupt-cells from a falsely acquired '1' to '2'
> referring to Documentation/devicetree/bindings/gpio/gpio-omap.txt:
>
>       The first cell is the GPIO number.
>       The second cell is used to specify flags:
>         bits[3:0] trigger type and level flags:
>           1 = low-to-high edge triggered.
>           2 = high-to-low edge triggered.
>           4 = active high level-sensitive.
>           8 = active low level-sensitive.
>
> But using this trigger cell in a board specific devicetree leads to a
> non-starting kernel. This is due to not yet enabled gpio-clocks while
> kernel/irq/irqdomain.c tries to set this trigger-flag (from the second
> interrupt-cell) to gpio-irq-controller.
>
>  Any ideas?

Hi Christoph,

A call to gpio_request() to enable the GPIO bank is needed before
using a GPIO as an IRQ source, otherwise accesses to the GPIO bank
registers fails making the kernel to hang. Jon's (added as cc)
"gpio/omap: warn if bank is not enabled on setting irq type" patch [1]
fixes the issue by warning and returning -EINVAL.

This patch will make the kernel to boot but the call to request_irq()
will fail of course. For now, the only solution is to call
gpio_request() before request_irq() in your platform code or device
driver. There is an on going discussion about what's the better way to
address this but we still haven't found a good solution to this
problem, you can see the last email for this discussion here [2]

Also, even when calling gpio_request() before request_irq() this won't
work. When specifying the trigger/level flags on the second cell for
an GPIO-IRQ, this is not set on the IORESOURCE_IRQ struct resource.
The IRQ flag is set on of_irq_to_resource() but it just does:

r->flags = IORESOURCE_IRQ;

and then the call stack is irq_to_parse_and_map() ->
irq_set_irq_type() ->  __irq_set_trigger() -> chip->irq_set_type() ->
(drivers/gpio/gpio-omap.c) gpio_irq_type().

So, even when gpio_irq_type() receive the correct flags, this are not
returned neither stored on the flags member of the IORESOURCE_IRQ
struct resource that passed to the drivers in their struct
platform_device.

I have on my TODO to better investigate if this behavior is
intentional or is a bug in the interrupt core but didn't have time to
work on this yet. A relevant discussion about this is here [3].

> ---
>  arch/arm/boot/dts/omap3.dtsi |   12 ++++++------
>  1 file changed, 6 insertions(+), 6 deletions(-)
>
> diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
> index 1997b41..e8e6b8f 100644
> --- a/arch/arm/boot/dts/omap3.dtsi
> +++ b/arch/arm/boot/dts/omap3.dtsi
> @@ -99,7 +99,7 @@
>                         gpio-controller;
>                         #gpio-cells = <2>;
>                         interrupt-controller;
> -                       #interrupt-cells = <1>;
> +                       #interrupt-cells = <2>;
>                 };
>
>                 gpio2: gpio at 49050000 {
> @@ -108,7 +108,7 @@
>                         gpio-controller;
>                         #gpio-cells = <2>;
>                         interrupt-controller;
> -                       #interrupt-cells = <1>;
> +                       #interrupt-cells = <2>;
>                 };
>
>                 gpio3: gpio at 49052000 {
> @@ -117,7 +117,7 @@
>                         gpio-controller;
>                         #gpio-cells = <2>;
>                         interrupt-controller;
> -                       #interrupt-cells = <1>;
> +                       #interrupt-cells = <2>;
>                 };
>
>                 gpio4: gpio at 49054000 {
> @@ -126,7 +126,7 @@
>                         gpio-controller;
>                         #gpio-cells = <2>;
>                         interrupt-controller;
> -                       #interrupt-cells = <1>;
> +                       #interrupt-cells = <2>;
>                 };
>
>                 gpio5: gpio at 49056000 {
> @@ -135,7 +135,7 @@
>                         gpio-controller;
>                         #gpio-cells = <2>;
>                         interrupt-controller;
> -                       #interrupt-cells = <1>;
> +                       #interrupt-cells = <2>;
>                 };
>
>                 gpio6: gpio at 49058000 {
> @@ -144,7 +144,7 @@
>                         gpio-controller;
>                         #gpio-cells = <2>;
>                         interrupt-controller;
> -                       #interrupt-cells = <1>;
> +                       #interrupt-cells = <2>;
>                 };
>
>                 uart1: serial at 4806a000 {
> --
> 1.7.10.4
>
>
>

By the way, Jon has already sent a "ARM: dts: OMAP3+: Correct gpio
#interrupts-cells property" patch [4] that changes #interrupt-cells to
<2> for all OMAP platforms.

Best regards,
Javier

[1]: https://patchwork.kernel.org/patch/2202511/
[2]: http://www.spinics.net/lists/linux-omap/msg89247.html
[3]: https://patchwork.kernel.org/patch/2194911/
[4]: https://patchwork.kernel.org/patch/2278081/



More information about the linux-arm-kernel mailing list