[PATCH] ARM: kirkwood: DT board setup for CloudBox
Andrew Lunn
andrew at lunn.ch
Fri Mar 29 13:09:44 EDT 2013
On Fri, Mar 29, 2013 at 12:06:46PM +0100, Simon Guinot wrote:
> This patch adds DT board setup for the LaCie NAS CloudBox. The CloudBox
> is a low cost NAS based on the Network Space v2.
>
> Chipset list:
> - CPU MARVELL 88F6702 1Ghz
> - SDRAM memory: 256MB DDR2-800 (2x128MB x8) 400Mhz
> - 1 Ethernet Gigabit port (PHY MARVELL 88E1318)
> - SPI flash, NOR 512KB
> - 1 push button
> - 2 LEDs (red and blue)
>
> Note that there is no EEPROM and no USB ports embedded.
>
> Signed-off-by: Simon Guinot <simon.guinot at sequanux.org>
> ---
> arch/arm/boot/dts/Makefile | 3 +-
> arch/arm/boot/dts/kirkwood-cloudbox.dts | 89 +++++++++++++++++++++++++++++++
> arch/arm/configs/kirkwood_defconfig | 1 +
> arch/arm/mach-kirkwood/Kconfig | 7 +++
> arch/arm/mach-kirkwood/Makefile | 1 +
> arch/arm/mach-kirkwood/board-dt.c | 4 +-
> arch/arm/mach-kirkwood/board-ns2.c | 3 +-
> arch/arm/mach-kirkwood/common.h | 6 +++
> 8 files changed, 111 insertions(+), 3 deletions(-)
> create mode 100644 arch/arm/boot/dts/kirkwood-cloudbox.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 9c62558..8b535ad 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -51,7 +51,8 @@ dtb-$(CONFIG_ARCH_HIGHBANK) += highbank.dtb \
> dtb-$(CONFIG_ARCH_INTEGRATOR) += integratorap.dtb \
> integratorcp.dtb
> dtb-$(CONFIG_ARCH_LPC32XX) += ea3250.dtb phy3250.dtb
> -dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-dns320.dtb \
> +dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \
> + kirkwood-dns320.dtb \
> kirkwood-dns325.dtb \
> kirkwood-dockstar.dtb \
> kirkwood-dreamplug.dtb \
> diff --git a/arch/arm/boot/dts/kirkwood-cloudbox.dts b/arch/arm/boot/dts/kirkwood-cloudbox.dts
> new file mode 100644
> index 0000000..93024b7
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-cloudbox.dts
> @@ -0,0 +1,89 @@
> +/dts-v1/;
> +
> +/include/ "kirkwood.dtsi"
> +/include/ "kirkwood-6281.dtsi"
> +
> +/ {
> + model = "LaCie CloudBox";
> + compatible = "lacie,cloudbox", "marvell,kirkwood-88f6702", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x10000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +
> + ocp at f1000000 {
> + pinctrl: pinctrl at 10000 {
> + pinctrl-0 = < &pmx_spi &pmx_twsi0 &pmx_uart0
Hi Simon
Is I2C used? You have pinctrl, but no nodes defined in DT.
> + &pmx_cloudbox_sata0 >;
> + pinctrl-names = "default";
> +
> + pmx_cloudbox_sata0: pmx-cloudbox-sata0 {
> + marvell,pins = "mpp15";
> + marvell,function = "sata0";
> + };
> + };
> +
> + serial at 12000 {
> + clock-frequency = <166666667>;
> + status = "okay";
> + };
> +
> + sata at 80000 {
> + status = "okay";
> + nr-ports = <1>;
> + };
> +
> + spi at 10600 {
> + status = "okay";
> +
> + flash at 0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "mx25l4005a";
> + reg = <0>;
> + spi-max-frequency = <20000000>;
> + mode = <0>;
> +
> + partition at 0 {
> + reg = <0x0 0x80000>;
> + label = "u-boot";
> + };
> + };
> + };
> + };
> +
> + gpio_keys {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + button at 1 {
> + label = "Power push button";
> + linux,code = <116>;
> + gpios = <&gpio0 16 1>;
> + };
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> +
> + red-fail {
> + label = "cloudbox:red:fail";
> + gpios = <&gpio0 14 0>;
> + };
> + blue-sata {
> + label = "cloudbox:blue:sata";
> + gpios = <&gpio0 15 0>;
> + };
> + };
> +
> + gpio_poweroff {
> + compatible = "gpio-poweroff";
> + gpios = <&gpio0 17 0>;
> + };
> +};
> diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
> index 13482ea..94aff34 100644
> --- a/arch/arm/configs/kirkwood_defconfig
> +++ b/arch/arm/configs/kirkwood_defconfig
> @@ -35,6 +35,7 @@ CONFIG_MACH_NETSPACE_LITE_V2_DT=y
> CONFIG_MACH_NETSPACE_MINI_V2_DT=y
> CONFIG_MACH_OPENBLOCKS_A6_DT=y
> CONFIG_MACH_TOPKICK_DT=y
> +CONFIG_MACH_CLOUDBOX_DT=y
Alphabetic order please. Same below for all other additions. Did Jason
already so that? Sorry, i did not read his reply yet.
Otherwise this looks good.
Andrew
> CONFIG_MACH_TS219=y
> CONFIG_MACH_TS41X=y
> CONFIG_MACH_DOCKSTAR=y
> diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
> index 7b6a64b..c6ffbce 100644
> --- a/arch/arm/mach-kirkwood/Kconfig
> +++ b/arch/arm/mach-kirkwood/Kconfig
> @@ -201,6 +201,13 @@ config MACH_TOPKICK_DT
> Say 'Y' here if you want your kernel to support the
> USI Topkick, using Flattened Device Tree
>
> +config MACH_CLOUDBOX_DT
> + bool "LaCie CloudBox NAS (Flattened Device Tree)"
> + select ARCH_KIRKWOOD_DT
> + help
> + Say 'Y' here if you want your kernel to support the LaCie
> + CloudBox NAS, using Flattened Device Tree.
> +
> config MACH_TS219
> bool "QNAP TS-110, TS-119, TS-119P+, TS-210, TS-219, TS-219P and TS-219P+ Turbo NAS"
> help
> diff --git a/arch/arm/mach-kirkwood/Makefile b/arch/arm/mach-kirkwood/Makefile
> index 4cc4bee..c1b81d3 100644
> --- a/arch/arm/mach-kirkwood/Makefile
> +++ b/arch/arm/mach-kirkwood/Makefile
> @@ -40,3 +40,4 @@ obj-$(CONFIG_MACH_NETSPACE_MINI_V2_DT) += board-ns2.o
> obj-$(CONFIG_MACH_NSA310_DT) += board-nsa310.o
> obj-$(CONFIG_MACH_OPENBLOCKS_A6_DT) += board-openblocks_a6.o
> obj-$(CONFIG_MACH_TOPKICK_DT) += board-usi_topkick.o
> +obj-$(CONFIG_MACH_CLOUDBOX_DT) += board-ns2.o
> diff --git a/arch/arm/mach-kirkwood/board-dt.c b/arch/arm/mach-kirkwood/board-dt.c
> index d367aa6..fdaac4e 100644
> --- a/arch/arm/mach-kirkwood/board-dt.c
> +++ b/arch/arm/mach-kirkwood/board-dt.c
> @@ -143,7 +143,8 @@ static void __init kirkwood_dt_init(void)
> of_machine_is_compatible("lacie,netspace_v2") ||
> of_machine_is_compatible("lacie,netspace_max_v2") ||
> of_machine_is_compatible("lacie,netspace_lite_v2") ||
> - of_machine_is_compatible("lacie,netspace_mini_v2"))
> + of_machine_is_compatible("lacie,netspace_mini_v2") ||
> + of_machine_is_compatible("lacie,cloudbox"))
> ns2_init();
>
> if (of_machine_is_compatible("mpl,cec4"))
> @@ -180,6 +181,7 @@ static const char * const kirkwood_dt_board_compat[] = {
> "plathome,openblocks-a6",
> "usi,topkick",
> "zyxel,nsa310",
> + "lacie,cloudbox",
> NULL
> };
>
> diff --git a/arch/arm/mach-kirkwood/board-ns2.c b/arch/arm/mach-kirkwood/board-ns2.c
> index f2ea3b7..5be000d 100644
> --- a/arch/arm/mach-kirkwood/board-ns2.c
> +++ b/arch/arm/mach-kirkwood/board-ns2.c
> @@ -28,7 +28,8 @@ void __init ns2_init(void)
> * Basic setup. Needs to be called early.
> */
> if (of_machine_is_compatible("lacie,netspace_lite_v2") ||
> - of_machine_is_compatible("lacie,netspace_mini_v2"))
> + of_machine_is_compatible("lacie,netspace_mini_v2") ||
> + of_machine_is_compatible("lacie,cloudbox"))
> ns2_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0);
> kirkwood_ge00_init(&ns2_ge00_data);
> }
> diff --git a/arch/arm/mach-kirkwood/common.h b/arch/arm/mach-kirkwood/common.h
> index 5ed7056..2b6d16a 100644
> --- a/arch/arm/mach-kirkwood/common.h
> +++ b/arch/arm/mach-kirkwood/common.h
> @@ -147,6 +147,12 @@ void usi_topkick_init(void);
> static inline void usi_topkick_init(void) {};
> #endif
>
> +#ifdef CONFIG_MACH_CLOUDBOX_DT
> +void cloudbox_init(void);
> +#else
> +static inline void cloudbox_init(void) {};
> +#endif
> +
> /* early init functions not converted to fdt yet */
> char *kirkwood_id(void);
> void kirkwood_l2_init(void);
> --
> 1.7.10.4
>
More information about the linux-arm-kernel
mailing list