[PATCH v6 1/8] dt: describe base reset signal binding
Philipp Zabel
p.zabel at pengutronix.de
Thu Mar 28 12:35:16 EDT 2013
From: Stephen Warren <swarren at nvidia.com>
This binding is intended to represent the hardware reset signals present
internally in most IC (SoC, FPGA, ...) designs.
It consists of a binding for a reset controller device (provider), and a
pair of properties, "resets" and "reset-names", to link a device node
(consumer) to its reset controller via phandle, similarly to the clock
and interrupt bindings.
The reset controller has all information necessary to reset the consumer
device. That could be provided via device tree, or it could be implemented
in hardware.
The aim is to enable device drivers to request a framework API to issue a
reset simply by providing their struct device pointer as the most common
case.
Signed-off-by: Stephen Warren <swarren at nvidia.com>
Signed-off-by: Philipp Zabel <p.zabel at pengutronix.de>
Reviewed-by: Shawn Guo <shawn.guo at linaro.org>
Reviewed-by: Marek Vasut <marex at denx.de>
---
Documentation/devicetree/bindings/reset/reset.txt | 75 +++++++++++++++++++++++
1 file changed, 75 insertions(+)
create mode 100644 Documentation/devicetree/bindings/reset/reset.txt
diff --git a/Documentation/devicetree/bindings/reset/reset.txt b/Documentation/devicetree/bindings/reset/reset.txt
new file mode 100644
index 0000000..31db6ff
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/reset.txt
@@ -0,0 +1,75 @@
+= Reset Signal Device Tree Bindings =
+
+This binding is intended to represent the hardware reset signals present
+internally in most IC (SoC, FPGA, ...) designs. Reset signals for whole
+standalone chips are most likely better represented as GPIOs, although there
+are likely to be exceptions to this rule.
+
+Hardware blocks typically receive a reset signal. This signal is generated by
+a reset provider (e.g. power management or clock module) and received by a
+reset consumer (the module being reset, or a module managing when a sub-
+ordinate module is reset). This binding exists to represent the provider and
+consumer, and provide a way to couple the two together.
+
+A reset signal is represented by the phandle of the provider, plus a reset
+specifier - a list of DT cells that represents the reset signal within the
+provider. The length (number of cells) and semantics of the reset specifier
+are dictated by the binding of the reset provider, although common schemes
+are described below.
+
+A word on where to place reset signal consumers in device tree: It is possible
+in hardware for a reset signal to affect multiple logically separate HW blocks
+at once. In this case, it would be unwise to represent this reset signal in
+the DT node of each affected HW block, since if activated, an unrelated block
+may be reset. Instead, reset signals should be represented in the DT node
+where it makes most sense to control it; this may be a bus node if all
+children of the bus are affected by the reset signal, or an individual HW
+block node for dedicated reset signals. The intent of this binding is to give
+appropriate software access to the reset signals in order to manage the HW,
+rather than to slavishly enumerate the reset signal that affects each HW
+block.
+
+= Reset providers =
+
+Required properties:
+#reset-cells: Number of cells in a reset specifier; Typically 0 for nodes
+ with a single reset output and 1 for nodes with multiple
+ reset outputs.
+
+For example:
+
+ rst: reset-controller {
+ #reset-cells = <1>;
+ };
+
+= Reset consumers =
+
+Required properties:
+resets: List of phandle and reset specifier pairs, one pair
+ for each reset signal that affects the device, or that the
+ device manages. Note: if the reset provider specifies '0' for
+ #reset-cells, then only the phandle portion of the pair will
+ appear.
+
+Optional properties:
+reset-names: List of reset signal name strings sorted in the same order as
+ the resets property. Consumers drivers will use reset-names to
+ match reset signal names with reset specifiers.
+
+For example:
+
+ device {
+ resets = <&rst 20>;
+ reset-names = "reset";
+ };
+
+This represents a device with a single reset signal named "reset".
+
+ bus {
+ resets = <&rst 10> <&rst 11> <&rst 12> <&rst 11>;
+ reset-names = "i2s1", "i2s2", "dma", "mixer";
+ };
+
+This represents a bus that controls the reset signal of each of four sub-
+ordinate devices. Consider for example a bus that fails to operate unless no
+child device has reset asserted.
--
1.8.2.rc2
More information about the linux-arm-kernel
mailing list