[PATCH] ARM: OMAP4: clock: Initialize USB DPLL
Roger Quadros
rogerq at ti.com
Thu Mar 21 10:12:35 EDT 2013
+Paul
On 03/21/2013 03:48 PM, Roger Quadros wrote:
> If the bootloader doesn't configure USB DPLL (e.g. in u-boot,
> disable CONFIG_USB_EHCI_OMAP), then we get all sorts of problems
> like
> - division by zero errors at boot [1]
> - USB DPLL fails to enter locked state
> - USB EHCI Host is non functional
> - Device can't enter OFF mode
>
> Initializing the USB DPLL fixes all these issues.
>
> [1]
>
> [ 0.000000] clock: dpll_usb_ck failed transition to 'locked'
> [ 0.000000] Division by zero in kernel.
> [ 0.000000] [<c001b00c>] (unwind_backtrace+0x0/0xf0) from [<c02b2378>] (Ldiv0+0x8/0x10)
> [ 0.000000] [<c02b2378>] (Ldiv0+0x8/0x10) from [<c041cf3c>] (clk_divider_set_rate+0x10/0x124)
> [ 0.000000] [<c041cf3c>] (clk_divider_set_rate+0x10/0x124) from [<c041bfc4>] (clk_change_rate+0x3c/0xb4)
> [ 0.000000] [<c041bfc4>] (clk_change_rate+0x3c/0xb4) from [<c041c028>] (clk_change_rate+0xa0/0xb4)
>
> Signed-off-by: Roger Quadros <rogerq at ti.com>
> ---
> arch/arm/mach-omap2/cclock44xx_data.c | 19 +++++++++++++++++++
> 1 files changed, 19 insertions(+), 0 deletions(-)
>
> diff --git a/arch/arm/mach-omap2/cclock44xx_data.c b/arch/arm/mach-omap2/cclock44xx_data.c
> index bfc46c1..6127bb9 100644
> --- a/arch/arm/mach-omap2/cclock44xx_data.c
> +++ b/arch/arm/mach-omap2/cclock44xx_data.c
> @@ -53,6 +53,12 @@
> */
> #define OMAP4_DPLL_ABE_DEFFREQ 98304000
>
> +/*
> + * OMAP4450 TRM Rev X, section "3.6.3.9.5 DPLL_USB Preferred Settings"
> + * states it must be at 960MHz
> + */
> +#define OMAP4_DPLL_USB_DEFFREQ 960000000
> +
> /* Root clocks */
>
> DEFINE_CLK_FIXED_RATE(extalt_clkin_ck, CLK_IS_ROOT, 59000000, 0x0);
> @@ -1729,6 +1735,19 @@ int __init omap4xxx_clk_init(void)
> omap2_clk_disable_autoidle_all();
>
> /*
> + * Lock USB_DPLL to avoid issues with USB host and OFF mode
> + */
> + rc = clk_set_rate(&dpll_usb_ck, OMAP4_DPLL_USB_DEFFREQ);
> + if (rc) {
> + pr_err("%s: failed to configure DPLL_USB: %d\n", __func__, rc);
> + } else {
> + rc = clk_set_rate(&dpll_usb_m2_ck, OMAP4_DPLL_USB_DEFFREQ/2);
> + if (rc)
> + pr_err("%s: failed to configure DPLL_USB_M2: %d\n",
> + __func__, rc);
> + }
> +
> + /*
> * On OMAP4460 the ABE DPLL fails to turn on if in idle low-power
> * state when turning the ABE clock domain. Workaround this by
> * locking the ABE DPLL on boot.
>
More information about the linux-arm-kernel
mailing list