[PATCH v4 13/21] ARM: OMAP3: omap3evm: Adapt to ehci-omap changes
Roger Quadros
rogerq at ti.com
Wed Mar 20 11:44:52 EDT 2013
Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device. VAUX2 supplies the PHY's VCC.
Signed-off-by: Roger Quadros <rogerq at ti.com>
---
arch/arm/mach-omap2/board-omap3evm.c | 25 +++++++++++++------------
1 files changed, 13 insertions(+), 12 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index 48789e0..2de92fa 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -496,7 +496,7 @@ struct wl12xx_platform_data omap3evm_wlan_data __initdata = {
static struct regulator_consumer_supply omap3evm_vaux2_supplies[] = {
REGULATOR_SUPPLY("VDD_CSIPHY1", "omap3isp"), /* OMAP ISP */
REGULATOR_SUPPLY("VDD_CSIPHY2", "omap3isp"), /* OMAP ISP */
- REGULATOR_SUPPLY("hsusb1", "ehci-omap.0"),
+ REGULATOR_SUPPLY("vcc", "nop_usb_xceiv.2"), /* hsusb port 2 */
REGULATOR_SUPPLY("vaux2", NULL),
};
@@ -539,17 +539,16 @@ static int __init omap3_evm_i2c_init(void)
return 0;
}
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
+static struct usbhs_phy_data phy_data[] __initdata = {
+ {
+ .port = 2,
+ .reset_gpio = -1, /* set at runtime */
+ .vcc_gpio = -EINVAL,
+ },
+};
- .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
+static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
- .phy_reset = true,
- /* PHY reset GPIO will be runtime programmed based on EVM version */
- .reset_gpio_port[0] = -EINVAL,
- .reset_gpio_port[1] = -EINVAL,
- .reset_gpio_port[2] = -EINVAL
};
#ifdef CONFIG_OMAP_MUX
@@ -725,7 +724,7 @@ static void __init omap3_evm_init(void)
/* setup EHCI phy reset config */
omap_mux_init_gpio(21, OMAP_PIN_INPUT_PULLUP);
- usbhs_bdata.reset_gpio_port[1] = 21;
+ phy_data[0].reset_gpio = 21;
/* EVM REV >= E can supply 500mA with EXTVBUS programming */
musb_board_data.power = 500;
@@ -733,10 +732,12 @@ static void __init omap3_evm_init(void)
} else {
/* setup EHCI phy reset on MDC */
omap_mux_init_gpio(135, OMAP_PIN_OUTPUT);
- usbhs_bdata.reset_gpio_port[1] = 135;
+ phy_data[0].reset_gpio = 135;
}
usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
usb_musb_init(&musb_board_data);
+
+ usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
usbhs_init(&usbhs_bdata);
board_nand_init(omap3evm_nand_partitions,
ARRAY_SIZE(omap3evm_nand_partitions), NAND_CS,
--
1.7.4.1
More information about the linux-arm-kernel
mailing list