[PATCH 5/6] ARM: kill Hynix h720x platform
Arnd Bergmann
arnd at arndb.de
Thu Mar 14 18:12:57 EDT 2013
The platform was merged about 10 years ago, and has seen few updates
for most of the time since. The people that merged the code seem
no longer interested in it either, so let's remove it now.
Signed-off-by: Arnd Bergmann <arnd at arndb.de>
Cc: Thomas Gleixner <tglx at linutronix.de>
Cc: Robert Schwebel <r.schwebel at pengutronix.de>
Cc: Sascha Hauer <s.hauer at pengutronix.de>
---
arch/arm/Kconfig | 10 -
arch/arm/Makefile | 1 -
arch/arm/configs/h7201_defconfig | 27 ---
arch/arm/configs/h7202_defconfig | 47 -----
arch/arm/mach-h720x/Kconfig | 40 ----
arch/arm/mach-h720x/Makefile | 16 --
arch/arm/mach-h720x/Makefile.boot | 2 -
arch/arm/mach-h720x/common.c | 268 -------------------------
arch/arm/mach-h720x/common.h | 30 ---
arch/arm/mach-h720x/cpu-h7201.c | 57 ------
arch/arm/mach-h720x/cpu-h7202.c | 225 ---------------------
arch/arm/mach-h720x/h7201-eval.c | 38 ----
arch/arm/mach-h720x/h7202-eval.c | 81 --------
arch/arm/mach-h720x/include/mach/boards.h | 53 -----
arch/arm/mach-h720x/include/mach/debug-macro.S | 40 ----
arch/arm/mach-h720x/include/mach/entry-macro.S | 57 ------
arch/arm/mach-h720x/include/mach/h7201-regs.h | 67 -------
arch/arm/mach-h720x/include/mach/h7202-regs.h | 155 --------------
arch/arm/mach-h720x/include/mach/hardware.h | 190 ------------------
arch/arm/mach-h720x/include/mach/irqs.h | 116 -----------
arch/arm/mach-h720x/include/mach/isa-dma.h | 19 --
arch/arm/mach-h720x/include/mach/timex.h | 15 --
arch/arm/mach-h720x/include/mach/uncompress.h | 36 ----
23 files changed, 1590 deletions(-)
delete mode 100644 arch/arm/configs/h7201_defconfig
delete mode 100644 arch/arm/configs/h7202_defconfig
delete mode 100644 arch/arm/mach-h720x/Kconfig
delete mode 100644 arch/arm/mach-h720x/Makefile
delete mode 100644 arch/arm/mach-h720x/Makefile.boot
delete mode 100644 arch/arm/mach-h720x/common.c
delete mode 100644 arch/arm/mach-h720x/common.h
delete mode 100644 arch/arm/mach-h720x/cpu-h7201.c
delete mode 100644 arch/arm/mach-h720x/cpu-h7202.c
delete mode 100644 arch/arm/mach-h720x/h7201-eval.c
delete mode 100644 arch/arm/mach-h720x/h7202-eval.c
delete mode 100644 arch/arm/mach-h720x/include/mach/boards.h
delete mode 100644 arch/arm/mach-h720x/include/mach/debug-macro.S
delete mode 100644 arch/arm/mach-h720x/include/mach/entry-macro.S
delete mode 100644 arch/arm/mach-h720x/include/mach/h7201-regs.h
delete mode 100644 arch/arm/mach-h720x/include/mach/h7202-regs.h
delete mode 100644 arch/arm/mach-h720x/include/mach/hardware.h
delete mode 100644 arch/arm/mach-h720x/include/mach/irqs.h
delete mode 100644 arch/arm/mach-h720x/include/mach/isa-dma.h
delete mode 100644 arch/arm/mach-h720x/include/mach/timex.h
delete mode 100644 arch/arm/mach-h720x/include/mach/uncompress.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 9d2e825..26e9251 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -485,14 +485,6 @@ config ARCH_NETX
help
This enables support for systems based on the Hilscher NetX Soc
-config ARCH_H720X
- bool "Hynix HMS720x-based"
- select ARCH_USES_GETTIMEOFFSET
- select CPU_ARM720T
- select ISA_DMA_API
- help
- This enables support for systems based on the Hynix HMS720x
-
config ARCH_IOP13XX
bool "IOP13xx-based"
depends on MMU
@@ -1041,8 +1033,6 @@ source "arch/arm/mach-ep93xx/Kconfig"
source "arch/arm/mach-footbridge/Kconfig"
-source "arch/arm/mach-h720x/Kconfig"
-
source "arch/arm/mach-highbank/Kconfig"
source "arch/arm/mach-integrator/Kconfig"
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index b514a0a..5f4576d 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -145,7 +145,6 @@ machine-$(CONFIG_ARCH_DAVINCI) += davinci
machine-$(CONFIG_ARCH_DOVE) += dove
machine-$(CONFIG_ARCH_EBSA110) += ebsa110
machine-$(CONFIG_ARCH_EP93XX) += ep93xx
-machine-$(CONFIG_ARCH_H720X) += h720x
machine-$(CONFIG_ARCH_HIGHBANK) += highbank
machine-$(CONFIG_ARCH_INTEGRATOR) += integrator
machine-$(CONFIG_ARCH_IOP13XX) += iop13xx
diff --git a/arch/arm/configs/h7201_defconfig b/arch/arm/configs/h7201_defconfig
deleted file mode 100644
index bee94d2..0000000
--- a/arch/arm/configs/h7201_defconfig
+++ /dev/null
@@ -1,27 +0,0 @@
-CONFIG_EXPERIMENTAL=y
-CONFIG_SYSVIPC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_MODULES=y
-CONFIG_ARCH_H720X=y
-CONFIG_ARCH_H7201=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_FPE_NWFPE=y
-CONFIG_MTD=y
-CONFIG_MTD_DEBUG=y
-CONFIG_MTD_PARTITIONS=y
-CONFIG_MTD_CHAR=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_CFI_ADV_OPTIONS=y
-CONFIG_MTD_CFI_INTELEXT=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=8192
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_SOUND=m
-CONFIG_EXT2_FS=y
-CONFIG_JFFS2_FS=y
-CONFIG_DEBUG_USER=y
diff --git a/arch/arm/configs/h7202_defconfig b/arch/arm/configs/h7202_defconfig
deleted file mode 100644
index e16d3f3..0000000
--- a/arch/arm/configs/h7202_defconfig
+++ /dev/null
@@ -1,47 +0,0 @@
-CONFIG_EXPERIMENTAL=y
-CONFIG_SYSVIPC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_MODULES=y
-CONFIG_ARCH_H720X=y
-CONFIG_ARCH_H7202=y
-# CONFIG_ARM_THUMB is not set
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="console=ttyS0,19200"
-CONFIG_FPE_NWFPE=y
-CONFIG_FPE_NWFPE_XP=y
-CONFIG_NET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_BOOTP=y
-# CONFIG_IPV6 is not set
-CONFIG_MTD=y
-CONFIG_MTD_PARTITIONS=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_CHAR=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_CFI_INTELEXT=y
-CONFIG_MTD_H720X=y
-CONFIG_NETDEVICES=y
-CONFIG_NET_ETHERNET=y
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_FB=y
-CONFIG_FB_MODE_HELPERS=y
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_USB_GADGET=m
-CONFIG_USB_ZERO=m
-CONFIG_USB_GADGETFS=m
-CONFIG_USB_MASS_STORAGE=m
-CONFIG_USB_G_SERIAL=m
-CONFIG_EXT2_FS=y
-CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_KERNEL=y
-CONFIG_DEBUG_INFO=y
-CONFIG_DEBUG_USER=y
diff --git a/arch/arm/mach-h720x/Kconfig b/arch/arm/mach-h720x/Kconfig
deleted file mode 100644
index 6bb755b..0000000
--- a/arch/arm/mach-h720x/Kconfig
+++ /dev/null
@@ -1,40 +0,0 @@
-if ARCH_H720X
-
-menu "h720x Implementations"
-
-config ARCH_H7201
- bool "gms30c7201"
- depends on ARCH_H720X
- select CPU_H7201
- select ZONE_DMA
- help
- Say Y here if you are using the Hynix GMS30C7201 Reference Board
-
-config ARCH_H7202
- bool "hms30c7202"
- depends on ARCH_H720X
- select CPU_H7202
- select ZONE_DMA
- help
- Say Y here if you are using the Hynix HMS30C7202 Reference Board
-
-endmenu
-
-config CPU_H7201
- bool
- help
- Select code specific to h7201 variants
-
-config CPU_H7202
- bool
- help
- Select code specific to h7202 variants
-config H7202_SERIAL23
- depends on CPU_H7202
- bool "Use serial ports 2+3"
- help
- Say Y here if you wish to use serial ports 2+3. They share their
- pins with the keyboard matrix controller, so you have to decide.
-
-
-endif
diff --git a/arch/arm/mach-h720x/Makefile b/arch/arm/mach-h720x/Makefile
deleted file mode 100644
index e4cf728..0000000
--- a/arch/arm/mach-h720x/Makefile
+++ /dev/null
@@ -1,16 +0,0 @@
-#
-# Makefile for the linux kernel.
-#
-
-# Common support
-obj-y := common.o
-obj-m :=
-obj-n :=
-obj- :=
-
-# Specific board support
-
-obj-$(CONFIG_ARCH_H7201) += h7201-eval.o
-obj-$(CONFIG_ARCH_H7202) += h7202-eval.o
-obj-$(CONFIG_CPU_H7201) += cpu-h7201.o
-obj-$(CONFIG_CPU_H7202) += cpu-h7202.o
diff --git a/arch/arm/mach-h720x/Makefile.boot b/arch/arm/mach-h720x/Makefile.boot
deleted file mode 100644
index d875a70..0000000
--- a/arch/arm/mach-h720x/Makefile.boot
+++ /dev/null
@@ -1,2 +0,0 @@
- zreladdr-$(CONFIG_ARCH_H720X) += 0x40008000
-
diff --git a/arch/arm/mach-h720x/common.c b/arch/arm/mach-h720x/common.c
deleted file mode 100644
index 17ef91f..0000000
--- a/arch/arm/mach-h720x/common.c
+++ /dev/null
@@ -1,268 +0,0 @@
-/*
- * linux/arch/arm/mach-h720x/common.c
- *
- * Copyright (C) 2003 Thomas Gleixner <tglx at linutronix.de>
- * 2003 Robert Schwebel <r.schwebel at pengutronix.de>
- * 2004 Sascha Hauer <s.hauer at pengutronix.de>
- *
- * common stuff for Hynix h720x processors
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-
-#include <linux/sched.h>
-#include <linux/mman.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/io.h>
-
-#include <asm/page.h>
-#include <asm/pgtable.h>
-#include <asm/dma.h>
-#include <mach/hardware.h>
-#include <asm/irq.h>
-#include <asm/system_misc.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/map.h>
-#include <mach/irqs.h>
-
-#include <asm/mach/dma.h>
-
-#if 0
-#define IRQDBG(args...) printk(args)
-#else
-#define IRQDBG(args...) do {} while(0)
-#endif
-
-void __init arch_dma_init(dma_t *dma)
-{
-}
-
-/*
- * Return nsecs since last timer reload
- * (timercount * (usecs perjiffie)) / (ticks per jiffie)
- */
-u32 h720x_gettimeoffset(void)
-{
- return ((CPU_REG(TIMER_VIRT, TM0_COUNT) * tick_usec) / LATCH) * 1000;
-}
-
-/*
- * mask Global irq's
- */
-static void mask_global_irq(struct irq_data *d)
-{
- CPU_REG (IRQC_VIRT, IRQC_IER) &= ~(1 << d->irq);
-}
-
-/*
- * unmask Global irq's
- */
-static void unmask_global_irq(struct irq_data *d)
-{
- CPU_REG (IRQC_VIRT, IRQC_IER) |= (1 << d->irq);
-}
-
-
-/*
- * ack GPIO irq's
- * Ack only for edge triggered int's valid
- */
-static void inline ack_gpio_irq(struct irq_data *d)
-{
- u32 reg_base = GPIO_VIRT(IRQ_TO_REGNO(d->irq));
- u32 bit = IRQ_TO_BIT(d->irq);
- if ( (CPU_REG (reg_base, GPIO_EDGE) & bit))
- CPU_REG (reg_base, GPIO_CLR) = bit;
-}
-
-/*
- * mask GPIO irq's
- */
-static void inline mask_gpio_irq(struct irq_data *d)
-{
- u32 reg_base = GPIO_VIRT(IRQ_TO_REGNO(d->irq));
- u32 bit = IRQ_TO_BIT(d->irq);
- CPU_REG (reg_base, GPIO_MASK) &= ~bit;
-}
-
-/*
- * unmask GPIO irq's
- */
-static void inline unmask_gpio_irq(struct irq_data *d)
-{
- u32 reg_base = GPIO_VIRT(IRQ_TO_REGNO(d->irq));
- u32 bit = IRQ_TO_BIT(d->irq);
- CPU_REG (reg_base, GPIO_MASK) |= bit;
-}
-
-static void
-h720x_gpio_handler(unsigned int mask, unsigned int irq,
- struct irq_desc *desc)
-{
- IRQDBG("%s irq: %d\n", __func__, irq);
- while (mask) {
- if (mask & 1) {
- IRQDBG("handling irq %d\n", irq);
- generic_handle_irq(irq);
- }
- irq++;
- mask >>= 1;
- }
-}
-
-static void
-h720x_gpioa_demux_handler(unsigned int irq_unused, struct irq_desc *desc)
-{
- unsigned int mask, irq;
-
- mask = CPU_REG(GPIO_A_VIRT,GPIO_STAT);
- irq = IRQ_CHAINED_GPIOA(0);
- IRQDBG("%s mask: 0x%08x irq: %d\n", __func__, mask,irq);
- h720x_gpio_handler(mask, irq, desc);
-}
-
-static void
-h720x_gpiob_demux_handler(unsigned int irq_unused, struct irq_desc *desc)
-{
- unsigned int mask, irq;
- mask = CPU_REG(GPIO_B_VIRT,GPIO_STAT);
- irq = IRQ_CHAINED_GPIOB(0);
- IRQDBG("%s mask: 0x%08x irq: %d\n", __func__, mask,irq);
- h720x_gpio_handler(mask, irq, desc);
-}
-
-static void
-h720x_gpioc_demux_handler(unsigned int irq_unused, struct irq_desc *desc)
-{
- unsigned int mask, irq;
-
- mask = CPU_REG(GPIO_C_VIRT,GPIO_STAT);
- irq = IRQ_CHAINED_GPIOC(0);
- IRQDBG("%s mask: 0x%08x irq: %d\n", __func__, mask,irq);
- h720x_gpio_handler(mask, irq, desc);
-}
-
-static void
-h720x_gpiod_demux_handler(unsigned int irq_unused, struct irq_desc *desc)
-{
- unsigned int mask, irq;
-
- mask = CPU_REG(GPIO_D_VIRT,GPIO_STAT);
- irq = IRQ_CHAINED_GPIOD(0);
- IRQDBG("%s mask: 0x%08x irq: %d\n", __func__, mask,irq);
- h720x_gpio_handler(mask, irq, desc);
-}
-
-#ifdef CONFIG_CPU_H7202
-static void
-h720x_gpioe_demux_handler(unsigned int irq_unused, struct irq_desc *desc)
-{
- unsigned int mask, irq;
-
- mask = CPU_REG(GPIO_E_VIRT,GPIO_STAT);
- irq = IRQ_CHAINED_GPIOE(0);
- IRQDBG("%s mask: 0x%08x irq: %d\n", __func__, mask,irq);
- h720x_gpio_handler(mask, irq, desc);
-}
-#endif
-
-static struct irq_chip h720x_global_chip = {
- .irq_ack = mask_global_irq,
- .irq_mask = mask_global_irq,
- .irq_unmask = unmask_global_irq,
-};
-
-static struct irq_chip h720x_gpio_chip = {
- .irq_ack = ack_gpio_irq,
- .irq_mask = mask_gpio_irq,
- .irq_unmask = unmask_gpio_irq,
-};
-
-/*
- * Initialize IRQ's, mask all, enable multiplexed irq's
- */
-void __init h720x_init_irq (void)
-{
- int irq;
-
- /* Mask global irq's */
- CPU_REG (IRQC_VIRT, IRQC_IER) = 0x0;
-
- /* Mask all multiplexed irq's */
- CPU_REG (GPIO_A_VIRT, GPIO_MASK) = 0x0;
- CPU_REG (GPIO_B_VIRT, GPIO_MASK) = 0x0;
- CPU_REG (GPIO_C_VIRT, GPIO_MASK) = 0x0;
- CPU_REG (GPIO_D_VIRT, GPIO_MASK) = 0x0;
-
- /* Initialize global IRQ's, fast path */
- for (irq = 0; irq < NR_GLBL_IRQS; irq++) {
- irq_set_chip_and_handler(irq, &h720x_global_chip,
- handle_level_irq);
- set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
- }
-
- /* Initialize multiplexed IRQ's, slow path */
- for (irq = IRQ_CHAINED_GPIOA(0) ; irq <= IRQ_CHAINED_GPIOD(31); irq++) {
- irq_set_chip_and_handler(irq, &h720x_gpio_chip,
- handle_edge_irq);
- set_irq_flags(irq, IRQF_VALID );
- }
- irq_set_chained_handler(IRQ_GPIOA, h720x_gpioa_demux_handler);
- irq_set_chained_handler(IRQ_GPIOB, h720x_gpiob_demux_handler);
- irq_set_chained_handler(IRQ_GPIOC, h720x_gpioc_demux_handler);
- irq_set_chained_handler(IRQ_GPIOD, h720x_gpiod_demux_handler);
-
-#ifdef CONFIG_CPU_H7202
- for (irq = IRQ_CHAINED_GPIOE(0) ; irq <= IRQ_CHAINED_GPIOE(31); irq++) {
- irq_set_chip_and_handler(irq, &h720x_gpio_chip,
- handle_edge_irq);
- set_irq_flags(irq, IRQF_VALID );
- }
- irq_set_chained_handler(IRQ_GPIOE, h720x_gpioe_demux_handler);
-#endif
-
- /* Enable multiplexed irq's */
- CPU_REG (IRQC_VIRT, IRQC_IER) = IRQ_ENA_MUX;
-}
-
-static struct map_desc h720x_io_desc[] __initdata = {
- {
- .virtual = IO_VIRT,
- .pfn = __phys_to_pfn(IO_PHYS),
- .length = IO_SIZE,
- .type = MT_DEVICE
- },
-};
-
-/* Initialize io tables */
-void __init h720x_map_io(void)
-{
- iotable_init(h720x_io_desc,ARRAY_SIZE(h720x_io_desc));
-}
-
-void h720x_restart(char mode, const char *cmd)
-{
- CPU_REG (PMU_BASE, PMU_STAT) |= PMU_WARMRESET;
-}
-
-static void h720x__idle(void)
-{
- CPU_REG (PMU_BASE, PMU_MODE) = PMU_MODE_IDLE;
- nop();
- nop();
- CPU_REG (PMU_BASE, PMU_MODE) = PMU_MODE_RUN;
- nop();
- nop();
-}
-
-static int __init h720x_idle_init(void)
-{
- arm_pm_idle = h720x__idle;
- return 0;
-}
-
-arch_initcall(h720x_idle_init);
diff --git a/arch/arm/mach-h720x/common.h b/arch/arm/mach-h720x/common.h
deleted file mode 100644
index 7e73841..0000000
--- a/arch/arm/mach-h720x/common.h
+++ /dev/null
@@ -1,30 +0,0 @@
-/*
- * linux/arch/arm/mach-h720x/common.h
- *
- * Copyright (C) 2003 Thomas Gleixner <tglx at linutronix.de>
- * 2003 Robert Schwebel <r.schwebel at pengutronix.de>
- * 2004 Sascha Hauer <s.hauer at pengutronix.de>
- *
- * Architecture specific stuff for Hynix GMS30C7201 development board
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-
-extern u32 h720x_gettimeoffset(void);
-extern void __init h720x_init_irq(void);
-extern void __init h720x_map_io(void);
-extern void h720x_restart(char, const char *);
-
-#ifdef CONFIG_ARCH_H7202
-extern void h7202_timer_init(void);
-extern void __init init_hw_h7202(void);
-extern void __init h7202_init_irq(void);
-extern void __init h7202_init_time(void);
-#endif
-
-#ifdef CONFIG_ARCH_H7201
-extern void h7201_timer_init(void);
-#endif
diff --git a/arch/arm/mach-h720x/cpu-h7201.c b/arch/arm/mach-h720x/cpu-h7201.c
deleted file mode 100644
index 13c7412..0000000
--- a/arch/arm/mach-h720x/cpu-h7201.c
+++ /dev/null
@@ -1,57 +0,0 @@
-/*
- * linux/arch/arm/mach-h720x/cpu-h7201.c
- *
- * Copyright (C) 2003 Thomas Gleixner <tglx at linutronix.de>
- * 2003 Robert Schwebel <r.schwebel at pengutronix.de>
- * 2004 Sascha Hauer <s.hauer at pengutronix.de>
- *
- * processor specific stuff for the Hynix h7201
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/module.h>
-#include <asm/types.h>
-#include <mach/hardware.h>
-#include <asm/irq.h>
-#include <mach/irqs.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/time.h>
-#include "common.h"
-/*
- * Timer interrupt handler
- */
-static irqreturn_t
-h7201_timer_interrupt(int irq, void *dev_id)
-{
- CPU_REG (TIMER_VIRT, TIMER_TOPSTAT);
- timer_tick();
-
- return IRQ_HANDLED;
-}
-
-static struct irqaction h7201_timer_irq = {
- .name = "h7201 Timer Tick",
- .flags = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
- .handler = h7201_timer_interrupt,
-};
-
-/*
- * Setup TIMER0 as system timer
- */
-void __init h7201_timer_init(void)
-{
- arch_gettimeoffset = h720x_gettimeoffset;
-
- CPU_REG (TIMER_VIRT, TM0_PERIOD) = LATCH;
- CPU_REG (TIMER_VIRT, TM0_CTRL) = TM_RESET;
- CPU_REG (TIMER_VIRT, TM0_CTRL) = TM_REPEAT | TM_START;
- CPU_REG (TIMER_VIRT, TIMER_TOPCTRL) = ENABLE_TM0_INTR | TIMER_ENABLE_BIT;
-
- setup_irq(IRQ_TIMER0, &h7201_timer_irq);
-}
diff --git a/arch/arm/mach-h720x/cpu-h7202.c b/arch/arm/mach-h720x/cpu-h7202.c
deleted file mode 100644
index e2ae7e8..0000000
--- a/arch/arm/mach-h720x/cpu-h7202.c
+++ /dev/null
@@ -1,225 +0,0 @@
-/*
- * linux/arch/arm/mach-h720x/cpu-h7202.c
- *
- * Copyright (C) 2003 Thomas Gleixner <tglx at linutronix.de>
- * 2003 Robert Schwebel <r.schwebel at pengutronix.de>
- * 2004 Sascha Hauer <s.hauer at pengutronix.de>
- *
- * processor specific stuff for the Hynix h7202
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/module.h>
-#include <asm/types.h>
-#include <mach/hardware.h>
-#include <asm/irq.h>
-#include <mach/irqs.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/time.h>
-#include <linux/device.h>
-#include <linux/serial_8250.h>
-#include "common.h"
-
-static struct resource h7202ps2_resources[] = {
- [0] = {
- .start = 0x8002c000,
- .end = 0x8002c040,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = IRQ_PS2,
- .end = IRQ_PS2,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device h7202ps2_device = {
- .name = "h7202ps2",
- .id = -1,
- .num_resources = ARRAY_SIZE(h7202ps2_resources),
- .resource = h7202ps2_resources,
-};
-
-static struct plat_serial8250_port serial_platform_data[] = {
- {
- .membase = (void*)SERIAL0_VIRT,
- .mapbase = SERIAL0_BASE,
- .irq = IRQ_UART0,
- .uartclk = 2*1843200,
- .regshift = 2,
- .iotype = UPIO_MEM,
- .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
- },
- {
- .membase = (void*)SERIAL1_VIRT,
- .mapbase = SERIAL1_BASE,
- .irq = IRQ_UART1,
- .uartclk = 2*1843200,
- .regshift = 2,
- .iotype = UPIO_MEM,
- .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
- },
-#ifdef CONFIG_H7202_SERIAL23
- {
- .membase = (void*)SERIAL2_VIRT,
- .mapbase = SERIAL2_BASE,
- .irq = IRQ_UART2,
- .uartclk = 2*1843200,
- .regshift = 2,
- .iotype = UPIO_MEM,
- .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
- },
- {
- .membase = (void*)SERIAL3_VIRT,
- .mapbase = SERIAL3_BASE,
- .irq = IRQ_UART3,
- .uartclk = 2*1843200,
- .regshift = 2,
- .iotype = UPIO_MEM,
- .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
- },
-#endif
- { },
-};
-
-static struct platform_device serial_device = {
- .name = "serial8250",
- .id = PLAT8250_DEV_PLATFORM,
- .dev = {
- .platform_data = serial_platform_data,
- },
-};
-
-static struct platform_device *devices[] __initdata = {
- &h7202ps2_device,
- &serial_device,
-};
-
-/* Although we have two interrupt lines for the timers, we only have one
- * status register which clears all pending timer interrupts on reading. So
- * we have to handle all timer interrupts in one place.
- */
-static void
-h7202_timerx_demux_handler(unsigned int irq_unused, struct irq_desc *desc)
-{
- unsigned int mask, irq;
-
- mask = CPU_REG (TIMER_VIRT, TIMER_TOPSTAT);
-
- if ( mask & TSTAT_T0INT ) {
- timer_tick();
- if( mask == TSTAT_T0INT )
- return;
- }
-
- mask >>= 1;
- irq = IRQ_TIMER1;
- while (mask) {
- if (mask & 1)
- generic_handle_irq(irq);
- irq++;
- mask >>= 1;
- }
-}
-
-/*
- * Timer interrupt handler
- */
-static irqreturn_t
-h7202_timer_interrupt(int irq, void *dev_id)
-{
- h7202_timerx_demux_handler(0, NULL);
- return IRQ_HANDLED;
-}
-
-/*
- * mask multiplexed timer IRQs
- */
-static void inline __mask_timerx_irq(unsigned int irq)
-{
- unsigned int bit;
- bit = 2 << ((irq == IRQ_TIMER64B) ? 4 : (irq - IRQ_TIMER1));
- CPU_REG (TIMER_VIRT, TIMER_TOPCTRL) &= ~bit;
-}
-
-static void inline mask_timerx_irq(struct irq_data *d)
-{
- __mask_timerx_irq(d->irq);
-}
-
-/*
- * unmask multiplexed timer IRQs
- */
-static void inline unmask_timerx_irq(struct irq_data *d)
-{
- unsigned int bit;
- bit = 2 << ((d->irq == IRQ_TIMER64B) ? 4 : (d->irq - IRQ_TIMER1));
- CPU_REG (TIMER_VIRT, TIMER_TOPCTRL) |= bit;
-}
-
-static struct irq_chip h7202_timerx_chip = {
- .irq_ack = mask_timerx_irq,
- .irq_mask = mask_timerx_irq,
- .irq_unmask = unmask_timerx_irq,
-};
-
-static struct irqaction h7202_timer_irq = {
- .name = "h7202 Timer Tick",
- .flags = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
- .handler = h7202_timer_interrupt,
-};
-
-/*
- * Setup TIMER0 as system timer
- */
-void __init h7202_timer_init(void)
-{
- arch_gettimeoffset = h720x_gettimeoffset;
-
- CPU_REG (TIMER_VIRT, TM0_PERIOD) = LATCH;
- CPU_REG (TIMER_VIRT, TM0_CTRL) = TM_RESET;
- CPU_REG (TIMER_VIRT, TM0_CTRL) = TM_REPEAT | TM_START;
- CPU_REG (TIMER_VIRT, TIMER_TOPCTRL) = ENABLE_TM0_INTR | TIMER_ENABLE_BIT;
-
- setup_irq(IRQ_TIMER0, &h7202_timer_irq);
-}
-
-void __init h7202_init_irq (void)
-{
- int irq;
-
- CPU_REG (GPIO_E_VIRT, GPIO_MASK) = 0x0;
-
- for (irq = IRQ_TIMER1;
- irq < IRQ_CHAINED_TIMERX(NR_TIMERX_IRQS); irq++) {
- __mask_timerx_irq(irq);
- irq_set_chip_and_handler(irq, &h7202_timerx_chip,
- handle_edge_irq);
- set_irq_flags(irq, IRQF_VALID );
- }
- irq_set_chained_handler(IRQ_TIMERX, h7202_timerx_demux_handler);
-
- h720x_init_irq();
-}
-
-void __init init_hw_h7202(void)
-{
- /* Enable clocks */
- CPU_REG (PMU_BASE, PMU_PLL_CTRL) |= PLL_2_EN | PLL_1_EN | PLL_3_MUTE;
-
- CPU_REG (SERIAL0_VIRT, SERIAL_ENABLE) = SERIAL_ENABLE_EN;
- CPU_REG (SERIAL1_VIRT, SERIAL_ENABLE) = SERIAL_ENABLE_EN;
-#ifdef CONFIG_H7202_SERIAL23
- CPU_REG (SERIAL2_VIRT, SERIAL_ENABLE) = SERIAL_ENABLE_EN;
- CPU_REG (SERIAL3_VIRT, SERIAL_ENABLE) = SERIAL_ENABLE_EN;
- CPU_IO (GPIO_AMULSEL) = AMULSEL_USIN2 | AMULSEL_USOUT2 |
- AMULSEL_USIN3 | AMULSEL_USOUT3;
-#endif
- (void) platform_add_devices(devices, ARRAY_SIZE(devices));
-}
diff --git a/arch/arm/mach-h720x/h7201-eval.c b/arch/arm/mach-h720x/h7201-eval.c
deleted file mode 100644
index 4fdeb68..0000000
--- a/arch/arm/mach-h720x/h7201-eval.c
+++ /dev/null
@@ -1,38 +0,0 @@
-/*
- * linux/arch/arm/mach-h720x/h7201-eval.c
- *
- * Copyright (C) 2003 Thomas Gleixner <tglx at linutronix.de>
- * 2003 Robert Schwebel <r.schwebel at pengutronix.de>
- * 2004 Sascha Hauer <s.hauer at pengutronix.de>
- *
- * Architecture specific stuff for Hynix GMS30C7201 development board
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/string.h>
-#include <linux/device.h>
-
-#include <asm/setup.h>
-#include <asm/types.h>
-#include <asm/mach-types.h>
-#include <asm/page.h>
-#include <asm/mach/arch.h>
-#include <mach/hardware.h>
-#include "common.h"
-
-MACHINE_START(H7201, "Hynix GMS30C7201")
- /* Maintainer: Robert Schwebel, Pengutronix */
- .atag_offset = 0x1000,
- .map_io = h720x_map_io,
- .init_irq = h720x_init_irq,
- .init_time = h7201_timer_init,
- .dma_zone_size = SZ_256M,
- .restart = h720x_restart,
-MACHINE_END
diff --git a/arch/arm/mach-h720x/h7202-eval.c b/arch/arm/mach-h720x/h7202-eval.c
deleted file mode 100644
index f68e967..0000000
--- a/arch/arm/mach-h720x/h7202-eval.c
+++ /dev/null
@@ -1,81 +0,0 @@
-/*
- * linux/arch/arm/mach-h720x/h7202-eval.c
- *
- * Copyright (C) 2003 Thomas Gleixner <tglx at linutronix.de>
- * 2003 Robert Schwebel <r.schwebel at pengutronix.de>
- * 2004 Sascha Hauer <s.hauer at pengutronix.de>
- *
- * Architecture specific stuff for Hynix HMS30C7202 development board
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/string.h>
-#include <linux/platform_device.h>
-
-#include <asm/setup.h>
-#include <asm/types.h>
-#include <asm/mach-types.h>
-#include <asm/page.h>
-#include <asm/mach/arch.h>
-#include <mach/irqs.h>
-#include <mach/hardware.h>
-#include "common.h"
-
-static struct resource cirrus_resources[] = {
- [0] = {
- .start = ETH0_PHYS + 0x300,
- .end = ETH0_PHYS + 0x300 + 0x10,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = IRQ_CHAINED_GPIOB(8),
- .end = IRQ_CHAINED_GPIOB(8),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device cirrus_device = {
- .name = "cirrus-cs89x0",
- .id = -1,
- .num_resources = ARRAY_SIZE(cirrus_resources),
- .resource = cirrus_resources,
-};
-
-static struct platform_device *devices[] __initdata = {
- &cirrus_device,
-};
-
-/*
- * Hardware init. This is called early in initcalls
- * Place pin inits here. So you avoid adding ugly
- * #ifdef stuff to common drivers.
- * Use this only, if your bootloader is not able
- * to initialize the pins proper.
- */
-static void __init init_eval_h7202(void)
-{
- init_hw_h7202();
- (void) platform_add_devices(devices, ARRAY_SIZE(devices));
-
- /* Enable interrupt on portb bit 8 (ethernet) */
- CPU_REG (GPIO_B_VIRT, GPIO_POL) &= ~(1 << 8);
- CPU_REG (GPIO_B_VIRT, GPIO_EN) |= (1 << 8);
-}
-
-MACHINE_START(H7202, "Hynix HMS30C7202")
- /* Maintainer: Robert Schwebel, Pengutronix */
- .atag_offset = 0x100,
- .map_io = h720x_map_io,
- .init_irq = h7202_init_irq,
- .init_time = h7202_timer_init,
- .init_machine = init_eval_h7202,
- .dma_zone_size = SZ_256M,
- .restart = h720x_restart,
-MACHINE_END
diff --git a/arch/arm/mach-h720x/include/mach/boards.h b/arch/arm/mach-h720x/include/mach/boards.h
deleted file mode 100644
index 38b8e0d..0000000
--- a/arch/arm/mach-h720x/include/mach/boards.h
+++ /dev/null
@@ -1,53 +0,0 @@
-/*
- * arch/arm/mach-h720x/include/mach/boards.h
- *
- * Copyright (C) 2003 Thomas Gleixner <tglx at linutronix.de>
- * (C) 2003 Robert Schwebel <r.schwebel at pengutronix.de>
- *
- * This file contains the board specific defines for various devices
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_HARDWARE_INCMACH_H
-#error Do not include this file directly. Include asm/hardware.h instead !
-#endif
-
-/* Hynix H7202 developer board specific device defines */
-#ifdef CONFIG_ARCH_H7202
-
-/* FLASH */
-#define H720X_FLASH_VIRT 0xd0000000
-#define H720X_FLASH_PHYS 0x00000000
-#define H720X_FLASH_SIZE 0x02000000
-
-/* onboard LAN controller */
-# define ETH0_PHYS 0x08000000
-
-/* Touch screen defines */
-/* GPIO Port */
-#define PEN_GPIO GPIO_B_VIRT
-/* Bitmask for pen down interrupt */
-#define PEN_INT_BIT (1<<7)
-/* Bitmask for pen up interrupt */
-#define PEN_ENA_BIT (1<<6)
-/* pen up interrupt */
-#define IRQ_PEN IRQ_MUX_GPIOB(7)
-
-#endif
-
-/* Hynix H7201 developer board specific device defines */
-#if defined (CONFIG_ARCH_H7201)
-/* ROM DISK SPACE */
-#define ROM_DISK_BASE 0xc1800000
-#define ROM_DISK_START 0x41800000
-#define ROM_DISK_SIZE 0x00700000
-
-/* SRAM DISK SPACE */
-#define SRAM_DISK_BASE 0xf1000000
-#define SRAM_DISK_START 0x04000000
-#define SRAM_DISK_SIZE 0x00400000
-#endif
-
diff --git a/arch/arm/mach-h720x/include/mach/debug-macro.S b/arch/arm/mach-h720x/include/mach/debug-macro.S
deleted file mode 100644
index 8a46157..0000000
--- a/arch/arm/mach-h720x/include/mach/debug-macro.S
+++ /dev/null
@@ -1,40 +0,0 @@
-/* arch/arm/mach-h720x/include/mach/debug-macro.S
- *
- * Debugging macro include header
- *
- * Copyright (C) 1994-1999 Russell King
- * Moved from linux/arch/arm/kernel/debug.S by Ben Dooks
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
-*/
-
-#include <mach/hardware.h>
-
- .equ io_virt, IO_VIRT
- .equ io_phys, IO_PHYS
-
- .macro addruart, rp, rv, tmp
- mov \rp, #0x00020000 @ UART1
- add \rv, \rp, #io_virt @ virtual address
- add \rp, \rp, #io_phys @ physical base address
- .endm
-
- .macro senduart,rd,rx
- str \rd, [\rx, #0x0] @ UARTDR
-
- .endm
-
- .macro waituart,rd,rx
-1001: ldr \rd, [\rx, #0x18] @ UARTFLG
- tst \rd, #1 << 5 @ UARTFLGUTXFF - 1 when full
- bne 1001b
- .endm
-
- .macro busyuart,rd,rx
-1001: ldr \rd, [\rx, #0x18] @ UARTFLG
- tst \rd, #1 << 3 @ UARTFLGUBUSY - 1 when busy
- bne 1001b
- .endm
diff --git a/arch/arm/mach-h720x/include/mach/entry-macro.S b/arch/arm/mach-h720x/include/mach/entry-macro.S
deleted file mode 100644
index 75267fa..0000000
--- a/arch/arm/mach-h720x/include/mach/entry-macro.S
+++ /dev/null
@@ -1,57 +0,0 @@
-/*
- * arch/arm/mach-h720x/include/mach/entry-macro.S
- *
- * Low-level IRQ helper macros for Hynix HMS720x based platforms
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
- .macro get_irqnr_preamble, base, tmp
- .endm
-
- .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
-#if defined (CONFIG_CPU_H7201) || defined (CONFIG_CPU_H7202)
- @ we could use the id register on H7202, but this is not
- @ properly updated when we come back from asm_do_irq
- @ without a previous return from interrupt
- @ (see loops below in irq_svc, irq_usr)
- @ We see unmasked pending ints only, as the masked pending ints
- @ are not visible here
-
- mov \base, #0xf0000000 @ base register
- orr \base, \base, #0x24000 @ irqbase
- ldr \irqstat, [\base, #0x04] @ get interrupt status
-#if defined (CONFIG_CPU_H7201)
- ldr \tmp, =0x001fffff
-#else
- mvn \tmp, #0xc0000000
-#endif
- and \irqstat, \irqstat, \tmp @ mask out unused ints
- mov \irqnr, #0
-
- mov \tmp, #0xff00
- orr \tmp, \tmp, #0xff
- tst \irqstat, \tmp
- addeq \irqnr, \irqnr, #16
- moveq \irqstat, \irqstat, lsr #16
- tst \irqstat, #255
- addeq \irqnr, \irqnr, #8
- moveq \irqstat, \irqstat, lsr #8
- tst \irqstat, #15
- addeq \irqnr, \irqnr, #4
- moveq \irqstat, \irqstat, lsr #4
- tst \irqstat, #3
- addeq \irqnr, \irqnr, #2
- moveq \irqstat, \irqstat, lsr #2
- tst \irqstat, #1
- addeq \irqnr, \irqnr, #1
- moveq \irqstat, \irqstat, lsr #1
- tst \irqstat, #1 @ bit 0 should be set
- .endm
-
-#else
-#error hynix processor selection missmatch
-#endif
-
diff --git a/arch/arm/mach-h720x/include/mach/h7201-regs.h b/arch/arm/mach-h720x/include/mach/h7201-regs.h
deleted file mode 100644
index 611b494..0000000
--- a/arch/arm/mach-h720x/include/mach/h7201-regs.h
+++ /dev/null
@@ -1,67 +0,0 @@
-/*
- * arch/arm/mach-h720x/include/mach/h7201-regs.h
- *
- * Copyright (C) 2000 Jungjun Kim, Hynix Semiconductor Inc.
- * (C) 2003 Thomas Gleixner <tglx at linutronix.de>
- * (C) 2003 Robert Schwebel <r.schwebel at pengutronix.de>
- * (C) 2004 Sascha Hauer <s.hauer at pengutronix.de>
- *
- * This file contains the hardware definitions of the h720x processors
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * Do not add implementations specific defines here. This files contains
- * only defines of the onchip peripherals. Add those defines to boards.h,
- * which is included by this file.
- */
-
-#define SERIAL2_VIRT (IO_VIRT + 0x50100)
-#define SERIAL3_VIRT (IO_VIRT + 0x50200)
-
-/*
- * PCMCIA
- */
-#define PCMCIA0_ATT_BASE 0xe5000000
-#define PCMCIA0_ATT_SIZE 0x00200000
-#define PCMCIA0_ATT_START 0x20000000
-#define PCMCIA0_MEM_BASE 0xe5200000
-#define PCMCIA0_MEM_SIZE 0x00200000
-#define PCMCIA0_MEM_START 0x24000000
-#define PCMCIA0_IO_BASE 0xe5400000
-#define PCMCIA0_IO_SIZE 0x00200000
-#define PCMCIA0_IO_START 0x28000000
-
-#define PCMCIA1_ATT_BASE 0xe5600000
-#define PCMCIA1_ATT_SIZE 0x00200000
-#define PCMCIA1_ATT_START 0x30000000
-#define PCMCIA1_MEM_BASE 0xe5800000
-#define PCMCIA1_MEM_SIZE 0x00200000
-#define PCMCIA1_MEM_START 0x34000000
-#define PCMCIA1_IO_BASE 0xe5a00000
-#define PCMCIA1_IO_SIZE 0x00200000
-#define PCMCIA1_IO_START 0x38000000
-
-#define PRIME3C_BASE 0xf0050000
-#define PRIME3C_SIZE 0x00001000
-#define PRIME3C_START 0x10000000
-
-/* VGA Controller */
-#define VGA_RAMBASE 0x50
-#define VGA_TIMING0 0x60
-#define VGA_TIMING1 0x64
-#define VGA_TIMING2 0x68
-#define VGA_TIMING3 0x6c
-
-#define LCD_CTRL_VGA_ENABLE 0x00000100
-#define LCD_CTRL_VGA_BPP_MASK 0x00000600
-#define LCD_CTRL_VGA_4BPP 0x00000000
-#define LCD_CTRL_VGA_8BPP 0x00000200
-#define LCD_CTRL_VGA_16BPP 0x00000300
-#define LCD_CTRL_SHARE_DMA 0x00000800
-#define LCD_CTRL_VDE 0x00100000
-#define LCD_CTRL_LPE 0x00400000 /* LCD Power enable */
-#define LCD_CTRL_BLE 0x00800000 /* LCD backlight enable */
-
-#define VGA_PALETTE_BASE (IO_VIRT + 0x10800)
diff --git a/arch/arm/mach-h720x/include/mach/h7202-regs.h b/arch/arm/mach-h720x/include/mach/h7202-regs.h
deleted file mode 100644
index 17c12eb..0000000
--- a/arch/arm/mach-h720x/include/mach/h7202-regs.h
+++ /dev/null
@@ -1,155 +0,0 @@
-/*
- * arch/arm/mach-h720x/include/mach/h7202-regs.h
- *
- * Copyright (C) 2000 Jungjun Kim, Hynix Semiconductor Inc.
- * (C) 2003 Thomas Gleixner <tglx at linutronix.de>
- * (C) 2003 Robert Schwebel <r.schwebel at pengutronix.de>
- * (C) 2004 Sascha Hauer <s.hauer at pengutronix.de>
- *
- * This file contains the hardware definitions of the h720x processors
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * Do not add implementations specific defines here. This files contains
- * only defines of the onchip peripherals. Add those defines to boards.h,
- * which is included by this file.
- */
-
-#define SERIAL2_OFS 0x2d000
-#define SERIAL2_BASE (IO_PHYS + SERIAL2_OFS)
-#define SERIAL2_VIRT (IO_VIRT + SERIAL2_OFS)
-#define SERIAL3_OFS 0x2e000
-#define SERIAL3_BASE (IO_PHYS + SERIAL3_OFS)
-#define SERIAL3_VIRT (IO_VIRT + SERIAL3_OFS)
-
-/* Matrix Keyboard Controller */
-#define KBD_VIRT (IO_VIRT + 0x22000)
-#define KBD_KBCR 0x00
-#define KBD_KBSC 0x04
-#define KBD_KBTR 0x08
-#define KBD_KBVR0 0x0C
-#define KBD_KBVR1 0x10
-#define KBD_KBSR 0x18
-
-#define KBD_KBCR_SCANENABLE (1 << 7)
-#define KBD_KBCR_NPOWERDOWN (1 << 2)
-#define KBD_KBCR_CLKSEL_MASK (3)
-#define KBD_KBCR_CLKSEL_PCLK2 0x0
-#define KBD_KBCR_CLKSEL_PCLK128 0x1
-#define KBD_KBCR_CLKSEL_PCLK256 0x2
-#define KBD_KBCR_CLKSEL_PCLK512 0x3
-
-#define KBD_KBSR_INTR (1 << 0)
-#define KBD_KBSR_WAKEUP (1 << 1)
-
-/* USB device controller */
-
-#define USBD_BASE (IO_VIRT + 0x12000)
-#define USBD_LENGTH 0x3C
-
-#define USBD_GCTRL 0x00
-#define USBD_EPCTRL 0x04
-#define USBD_INTMASK 0x08
-#define USBD_INTSTAT 0x0C
-#define USBD_PWR 0x10
-#define USBD_DMARXTX 0x14
-#define USBD_DEVID 0x18
-#define USBD_DEVCLASS 0x1C
-#define USBD_INTCLASS 0x20
-#define USBD_SETUP0 0x24
-#define USBD_SETUP1 0x28
-#define USBD_ENDP0RD 0x2C
-#define USBD_ENDP0WT 0x30
-#define USBD_ENDP1RD 0x34
-#define USBD_ENDP2WT 0x38
-
-/* PS/2 port */
-#define PSDATA 0x00
-#define PSSTAT 0x04
-#define PSSTAT_TXEMPTY (1<<0)
-#define PSSTAT_TXBUSY (1<<1)
-#define PSSTAT_RXFULL (1<<2)
-#define PSSTAT_RXBUSY (1<<3)
-#define PSSTAT_CLKIN (1<<4)
-#define PSSTAT_DATAIN (1<<5)
-#define PSSTAT_PARITY (1<<6)
-
-#define PSCONF 0x08
-#define PSCONF_ENABLE (1<<0)
-#define PSCONF_TXINTEN (1<<2)
-#define PSCONF_RXINTEN (1<<3)
-#define PSCONF_FORCECLKLOW (1<<4)
-#define PSCONF_FORCEDATLOW (1<<5)
-#define PSCONF_LCE (1<<6)
-
-#define PSINTR 0x0C
-#define PSINTR_TXINT (1<<0)
-#define PSINTR_RXINT (1<<1)
-#define PSINTR_PAR (1<<2)
-#define PSINTR_RXTO (1<<3)
-#define PSINTR_TXTO (1<<4)
-
-#define PSTDLO 0x10 /* clk low before start transmission */
-#define PSTPRI 0x14 /* PRI clock */
-#define PSTXMT 0x18 /* maximum transmission time */
-#define PSTREC 0x20 /* maximum receive time */
-#define PSPWDN 0x3c
-
-/* ADC converter */
-#define ADC_BASE (IO_VIRT + 0x29000)
-#define ADC_CR 0x00
-#define ADC_TSCTRL 0x04
-#define ADC_BT_CTRL 0x08
-#define ADC_MC_CTRL 0x0C
-#define ADC_STATUS 0x10
-
-/* ADC control register bits */
-#define ADC_CR_PW_CTRL 0x80
-#define ADC_CR_DIRECTC 0x04
-#define ADC_CR_CONTIME_NO 0x00
-#define ADC_CR_CONTIME_2 0x04
-#define ADC_CR_CONTIME_4 0x08
-#define ADC_CR_CONTIME_ADE 0x0c
-#define ADC_CR_LONGCALTIME 0x01
-
-/* ADC touch panel register bits */
-#define ADC_TSCTRL_ENABLE 0x80
-#define ADC_TSCTRL_INTR 0x40
-#define ADC_TSCTRL_SWBYPSS 0x20
-#define ADC_TSCTRL_SWINVT 0x10
-#define ADC_TSCTRL_S400 0x03
-#define ADC_TSCTRL_S200 0x02
-#define ADC_TSCTRL_S100 0x01
-#define ADC_TSCTRL_S50 0x00
-
-/* ADC Interrupt Status Register bits */
-#define ADC_STATUS_TS_BIT 0x80
-#define ADC_STATUS_MBT_BIT 0x40
-#define ADC_STATUS_BBT_BIT 0x20
-#define ADC_STATUS_MIC_BIT 0x10
-
-/* Touch data registers */
-#define ADC_TS_X0X1 0x30
-#define ADC_TS_X2X3 0x34
-#define ADC_TS_Y0Y1 0x38
-#define ADC_TS_Y2Y3 0x3c
-#define ADC_TS_X4X5 0x40
-#define ADC_TS_X6X7 0x44
-#define ADC_TS_Y4Y5 0x48
-#define ADC_TS_Y6Y7 0x50
-
-/* battery data */
-#define ADC_MB_DATA 0x54
-#define ADC_BB_DATA 0x58
-
-/* Sound data register */
-#define ADC_SD_DAT0 0x60
-#define ADC_SD_DAT1 0x64
-#define ADC_SD_DAT2 0x68
-#define ADC_SD_DAT3 0x6c
-#define ADC_SD_DAT4 0x70
-#define ADC_SD_DAT5 0x74
-#define ADC_SD_DAT6 0x78
-#define ADC_SD_DAT7 0x7c
diff --git a/arch/arm/mach-h720x/include/mach/hardware.h b/arch/arm/mach-h720x/include/mach/hardware.h
deleted file mode 100644
index c55a52c..0000000
--- a/arch/arm/mach-h720x/include/mach/hardware.h
+++ /dev/null
@@ -1,190 +0,0 @@
-/*
- * arch/arm/mach-h720x/include/mach/hardware.h
- *
- * Copyright (C) 2000 Jungjun Kim, Hynix Semiconductor Inc.
- * (C) 2003 Thomas Gleixner <tglx at linutronix.de>
- * (C) 2003 Robert Schwebel <r.schwebel at pengutronix.de>
- *
- * This file contains the hardware definitions of the h720x processors
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * Do not add implementations specific defines here. This files contains
- * only defines of the onchip peripherals. Add those defines to boards.h,
- * which is included by this file.
- */
-
-#ifndef __ASM_ARCH_HARDWARE_H
-#define __ASM_ARCH_HARDWARE_H
-
-#define IOCLK (3686400L)
-
-/* Onchip peripherals */
-
-#define IO_VIRT 0xf0000000 /* IO peripherals */
-#define IO_PHYS 0x80000000
-#define IO_SIZE 0x00050000
-
-#ifdef CONFIG_CPU_H7202
-#include "h7202-regs.h"
-#elif defined CONFIG_CPU_H7201
-#include "h7201-regs.h"
-#else
-#error machine definition mismatch
-#endif
-
-/* Macro to access the CPU IO */
-#define CPU_IO(x) (*(volatile u32*)(x))
-
-/* Macro to access general purpose regs (base, offset) */
-#define CPU_REG(x,y) CPU_IO(x+y)
-
-/* Macro to access irq related regs */
-#define IRQ_REG(x) CPU_REG(IRQC_VIRT,x)
-
-/* CPU registers */
-/* general purpose I/O */
-#define GPIO_VIRT(x) (IO_VIRT + 0x23000 + ((x)<<5))
-#define GPIO_A_VIRT (GPIO_VIRT(0))
-#define GPIO_B_VIRT (GPIO_VIRT(1))
-#define GPIO_C_VIRT (GPIO_VIRT(2))
-#define GPIO_D_VIRT (GPIO_VIRT(3))
-#define GPIO_E_VIRT (GPIO_VIRT(4))
-#define GPIO_AMULSEL (GPIO_VIRT(0) + 0xA4)
-
-#define AMULSEL_USIN2 (1<<5)
-#define AMULSEL_USOUT2 (1<<6)
-#define AMULSEL_USIN3 (1<<13)
-#define AMULSEL_USOUT3 (1<<14)
-#define AMULSEL_IRDIN (1<<15)
-#define AMULSEL_IRDOUT (1<<7)
-
-/* Register offsets general purpose I/O */
-#define GPIO_DATA 0x00
-#define GPIO_DIR 0x04
-#define GPIO_MASK 0x08
-#define GPIO_STAT 0x0C
-#define GPIO_EDGE 0x10
-#define GPIO_CLR 0x14
-#define GPIO_POL 0x18
-#define GPIO_EN 0x1C
-
-/*interrupt controller */
-#define IRQC_VIRT (IO_VIRT + 0x24000)
-/* register offset interrupt controller */
-#define IRQC_IER 0x00
-#define IRQC_ISR 0x04
-
-/* timer unit */
-#define TIMER_VIRT (IO_VIRT + 0x25000)
-/* Register offsets timer unit */
-#define TM0_PERIOD 0x00
-#define TM0_COUNT 0x08
-#define TM0_CTRL 0x10
-#define TM1_PERIOD 0x20
-#define TM1_COUNT 0x28
-#define TM1_CTRL 0x30
-#define TM2_PERIOD 0x40
-#define TM2_COUNT 0x48
-#define TM2_CTRL 0x50
-#define TIMER_TOPCTRL 0x60
-#define TIMER_TOPSTAT 0x64
-#define T64_COUNTL 0x80
-#define T64_COUNTH 0x84
-#define T64_CTRL 0x88
-#define T64_BASEL 0x94
-#define T64_BASEH 0x98
-/* Bitmaks timer unit TOPSTAT reg */
-#define TSTAT_T0INT 0x1
-#define TSTAT_T1INT 0x2
-#define TSTAT_T2INT 0x4
-#define TSTAT_T3INT 0x8
-/* Bit description of TMx_CTRL register */
-#define TM_START 0x1
-#define TM_REPEAT 0x2
-#define TM_RESET 0x4
-/* Bit description of TIMER_CTRL register */
-#define ENABLE_TM0_INTR 0x1
-#define ENABLE_TM1_INTR 0x2
-#define ENABLE_TM2_INTR 0x4
-#define TIMER_ENABLE_BIT 0x8
-#define ENABLE_TIMER64 0x10
-#define ENABLE_TIMER64_INT 0x20
-
-/* PMU & PLL */
-#define PMU_BASE (IO_VIRT + 0x1000)
-#define PMU_MODE 0x00
-#define PMU_STAT 0x20
-#define PMU_PLL_CTRL 0x28
-
-/* PMU Mode bits */
-#define PMU_MODE_SLOW 0x00
-#define PMU_MODE_RUN 0x01
-#define PMU_MODE_IDLE 0x02
-#define PMU_MODE_SLEEP 0x03
-#define PMU_MODE_INIT 0x04
-#define PMU_MODE_DEEPSLEEP 0x07
-#define PMU_MODE_WAKEUP 0x08
-
-/* PMU ... */
-#define PLL_2_EN 0x8000
-#define PLL_1_EN 0x4000
-#define PLL_3_MUTE 0x0080
-
-/* Control bits for PMU/ PLL */
-#define PMU_WARMRESET 0x00010000
-#define PLL_CTRL_MASK23 0x000080ff
-
-/* LCD Controller */
-#define LCD_BASE (IO_VIRT + 0x10000)
-#define LCD_CTRL 0x00
-#define LCD_STATUS 0x04
-#define LCD_STATUS_M 0x08
-#define LCD_INTERRUPT 0x0C
-#define LCD_DBAR 0x10
-#define LCD_DCAR 0x14
-#define LCD_TIMING0 0x20
-#define LCD_TIMING1 0x24
-#define LCD_TIMING2 0x28
-#define LCD_TEST 0x40
-
-/* LCD Control Bits */
-#define LCD_CTRL_LCD_ENABLE 0x00000001
-/* Bits per pixel */
-#define LCD_CTRL_LCD_BPP_MASK 0x00000006
-#define LCD_CTRL_LCD_4BPP 0x00000000
-#define LCD_CTRL_LCD_8BPP 0x00000002
-#define LCD_CTRL_LCD_16BPP 0x00000004
-#define LCD_CTRL_LCD_BW 0x00000008
-#define LCD_CTRL_LCD_TFT 0x00000010
-#define LCD_CTRL_BGR 0x00001000
-#define LCD_CTRL_LCD_VCOMP 0x00080000
-#define LCD_CTRL_LCD_MONO8 0x00200000
-#define LCD_CTRL_LCD_PWR 0x00400000
-#define LCD_CTRL_LCD_BLE 0x00800000
-#define LCD_CTRL_LDBUSEN 0x01000000
-
-/* Palette */
-#define LCD_PALETTE_BASE (IO_VIRT + 0x10400)
-
-/* Serial ports */
-#define SERIAL0_OFS 0x20000
-#define SERIAL0_VIRT (IO_VIRT + SERIAL0_OFS)
-#define SERIAL0_BASE (IO_PHYS + SERIAL0_OFS)
-
-#define SERIAL1_OFS 0x21000
-#define SERIAL1_VIRT (IO_VIRT + SERIAL1_OFS)
-#define SERIAL1_BASE (IO_PHYS + SERIAL1_OFS)
-
-#define SERIAL_ENABLE 0x30
-#define SERIAL_ENABLE_EN (1<<0)
-
-/* General defines to pacify gcc */
-
-#define __ASM_ARCH_HARDWARE_INCMACH_H
-#include "boards.h"
-#undef __ASM_ARCH_HARDWARE_INCMACH_H
-
-#endif /* __ASM_ARCH_HARDWARE_H */
diff --git a/arch/arm/mach-h720x/include/mach/irqs.h b/arch/arm/mach-h720x/include/mach/irqs.h
deleted file mode 100644
index 430a92b..0000000
--- a/arch/arm/mach-h720x/include/mach/irqs.h
+++ /dev/null
@@ -1,116 +0,0 @@
-/*
- * arch/arm/mach-h720x/include/mach/irqs.h
- *
- * Copyright (C) 2000 Jungjun Kim
- * (C) 2003 Robert Schwebel <r.schwebel at pengutronix.de>
- * (C) 2003 Thomas Gleixner <tglx at linutronix.de>
- *
- */
-
-#ifndef __ASM_ARCH_IRQS_H
-#define __ASM_ARCH_IRQS_H
-
-#if defined (CONFIG_CPU_H7201)
-
-#define IRQ_PMU 0 /* 0x000001 */
-#define IRQ_DMA 1 /* 0x000002 */
-#define IRQ_LCD 2 /* 0x000004 */
-#define IRQ_VGA 3 /* 0x000008 */
-#define IRQ_PCMCIA1 4 /* 0x000010 */
-#define IRQ_PCMCIA2 5 /* 0x000020 */
-#define IRQ_AFE 6 /* 0x000040 */
-#define IRQ_AIC 7 /* 0x000080 */
-#define IRQ_KEYBOARD 8 /* 0x000100 */
-#define IRQ_TIMER0 9 /* 0x000200 */
-#define IRQ_RTC 10 /* 0x000400 */
-#define IRQ_SOUND 11 /* 0x000800 */
-#define IRQ_USB 12 /* 0x001000 */
-#define IRQ_IrDA 13 /* 0x002000 */
-#define IRQ_UART0 14 /* 0x004000 */
-#define IRQ_UART1 15 /* 0x008000 */
-#define IRQ_SPI 16 /* 0x010000 */
-#define IRQ_GPIOA 17 /* 0x020000 */
-#define IRQ_GPIOB 18 /* 0x040000 */
-#define IRQ_GPIOC 19 /* 0x080000 */
-#define IRQ_GPIOD 20 /* 0x100000 */
-#define IRQ_CommRX 21 /* 0x200000 */
-#define IRQ_CommTX 22 /* 0x400000 */
-#define IRQ_Soft 23 /* 0x800000 */
-
-#define NR_GLBL_IRQS 24
-
-#define IRQ_CHAINED_GPIOA(x) (NR_GLBL_IRQS + x)
-#define IRQ_CHAINED_GPIOB(x) (IRQ_CHAINED_GPIOA(32) + x)
-#define IRQ_CHAINED_GPIOC(x) (IRQ_CHAINED_GPIOB(32) + x)
-#define IRQ_CHAINED_GPIOD(x) (IRQ_CHAINED_GPIOC(32) + x)
-#define NR_IRQS IRQ_CHAINED_GPIOD(32)
-
-/* Enable mask for multiplexed interrupts */
-#define IRQ_ENA_MUX (1<<IRQ_GPIOA) | (1<<IRQ_GPIOB) \
- | (1<<IRQ_GPIOC) | (1<<IRQ_GPIOD)
-
-
-#elif defined (CONFIG_CPU_H7202)
-
-#define IRQ_PMU 0 /* 0x00000001 */
-#define IRQ_DMA 1 /* 0x00000002 */
-#define IRQ_LCD 2 /* 0x00000004 */
-#define IRQ_SOUND 3 /* 0x00000008 */
-#define IRQ_I2S 4 /* 0x00000010 */
-#define IRQ_USB 5 /* 0x00000020 */
-#define IRQ_MMC 6 /* 0x00000040 */
-#define IRQ_RTC 7 /* 0x00000080 */
-#define IRQ_UART0 8 /* 0x00000100 */
-#define IRQ_UART1 9 /* 0x00000200 */
-#define IRQ_UART2 10 /* 0x00000400 */
-#define IRQ_UART3 11 /* 0x00000800 */
-#define IRQ_KBD 12 /* 0x00001000 */
-#define IRQ_PS2 13 /* 0x00002000 */
-#define IRQ_AIC 14 /* 0x00004000 */
-#define IRQ_TIMER0 15 /* 0x00008000 */
-#define IRQ_TIMERX 16 /* 0x00010000 */
-#define IRQ_WDT 17 /* 0x00020000 */
-#define IRQ_CAN0 18 /* 0x00040000 */
-#define IRQ_CAN1 19 /* 0x00080000 */
-#define IRQ_EXT0 20 /* 0x00100000 */
-#define IRQ_EXT1 21 /* 0x00200000 */
-#define IRQ_GPIOA 22 /* 0x00400000 */
-#define IRQ_GPIOB 23 /* 0x00800000 */
-#define IRQ_GPIOC 24 /* 0x01000000 */
-#define IRQ_GPIOD 25 /* 0x02000000 */
-#define IRQ_GPIOE 26 /* 0x04000000 */
-#define IRQ_COMMRX 27 /* 0x08000000 */
-#define IRQ_COMMTX 28 /* 0x10000000 */
-#define IRQ_SMC 29 /* 0x20000000 */
-#define IRQ_Soft 30 /* 0x40000000 */
-#define IRQ_RESERVED1 31 /* 0x80000000 */
-#define NR_GLBL_IRQS 32
-
-#define NR_TIMERX_IRQS 3
-
-#define IRQ_CHAINED_GPIOA(x) (NR_GLBL_IRQS + x)
-#define IRQ_CHAINED_GPIOB(x) (IRQ_CHAINED_GPIOA(32) + x)
-#define IRQ_CHAINED_GPIOC(x) (IRQ_CHAINED_GPIOB(32) + x)
-#define IRQ_CHAINED_GPIOD(x) (IRQ_CHAINED_GPIOC(32) + x)
-#define IRQ_CHAINED_GPIOE(x) (IRQ_CHAINED_GPIOD(32) + x)
-#define IRQ_CHAINED_TIMERX(x) (IRQ_CHAINED_GPIOE(32) + x)
-#define IRQ_TIMER1 (IRQ_CHAINED_TIMERX(0))
-#define IRQ_TIMER2 (IRQ_CHAINED_TIMERX(1))
-#define IRQ_TIMER64B (IRQ_CHAINED_TIMERX(2))
-
-#define NR_IRQS (IRQ_CHAINED_TIMERX(NR_TIMERX_IRQS))
-
-/* Enable mask for multiplexed interrupts */
-#define IRQ_ENA_MUX (1<<IRQ_TIMERX) | (1<<IRQ_GPIOA) | (1<<IRQ_GPIOB) | \
- (1<<IRQ_GPIOC) | (1<<IRQ_GPIOD) | (1<<IRQ_GPIOE) | \
- (1<<IRQ_TIMERX)
-
-#else
-#error cpu definition mismatch
-#endif
-
-/* decode irq number to register number */
-#define IRQ_TO_REGNO(irq) ((irq - NR_GLBL_IRQS) >> 5)
-#define IRQ_TO_BIT(irq) (1 << ((irq - NR_GLBL_IRQS) % 32))
-
-#endif
diff --git a/arch/arm/mach-h720x/include/mach/isa-dma.h b/arch/arm/mach-h720x/include/mach/isa-dma.h
deleted file mode 100644
index 3eafb3f..0000000
--- a/arch/arm/mach-h720x/include/mach/isa-dma.h
+++ /dev/null
@@ -1,19 +0,0 @@
-/*
- * arch/arm/mach-h720x/include/mach/isa-dma.h
- *
- * Architecture DMA routes
- *
- * Copyright (C) 1997.1998 Russell King
- */
-#ifndef __ASM_ARCH_DMA_H
-#define __ASM_ARCH_DMA_H
-
-#if defined (CONFIG_CPU_H7201)
-#define MAX_DMA_CHANNELS 3
-#elif defined (CONFIG_CPU_H7202)
-#define MAX_DMA_CHANNELS 4
-#else
-#error processor definition missmatch
-#endif
-
-#endif /* __ASM_ARCH_DMA_H */
diff --git a/arch/arm/mach-h720x/include/mach/timex.h b/arch/arm/mach-h720x/include/mach/timex.h
deleted file mode 100644
index 3f2f447..0000000
--- a/arch/arm/mach-h720x/include/mach/timex.h
+++ /dev/null
@@ -1,15 +0,0 @@
-/*
- * arch/arm/mach-h720x/include/mach/timex.h
- * Copyright (C) 2000 Jungjun Kim, Hynix Semiconductor Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_TIMEX
-#define __ASM_ARCH_TIMEX
-
-#define CLOCK_TICK_RATE 3686400
-
-#endif
diff --git a/arch/arm/mach-h720x/include/mach/uncompress.h b/arch/arm/mach-h720x/include/mach/uncompress.h
deleted file mode 100644
index 43e343c..0000000
--- a/arch/arm/mach-h720x/include/mach/uncompress.h
+++ /dev/null
@@ -1,36 +0,0 @@
-/*
- * arch/arm/mach-h720x/include/mach/uncompress.h
- *
- * Copyright (C) 2001-2002 Jungjun Kim
- */
-
-#ifndef __ASM_ARCH_UNCOMPRESS_H
-#define __ASM_ARCH_UNCOMPRESS_H
-
-#include <mach/hardware.h>
-
-#define LSR 0x14
-#define TEMPTY 0x40
-
-static inline void putc(int c)
-{
- volatile unsigned char *p = (volatile unsigned char *)(IO_PHYS+0x20000);
-
- /* wait until transmit buffer is empty */
- while((p[LSR] & TEMPTY) == 0x0)
- barrier();
-
- /* write next character */
- *p = c;
-}
-
-static inline void flush(void)
-{
-}
-
-/*
- * nothing to do
- */
-#define arch_decomp_setup()
-
-#endif
--
1.8.1.2
More information about the linux-arm-kernel
mailing list