[PATCH 2/2] arm: at91: dt: at91sam9x5: add i2c-gpio pinctrl

Nicolas Ferre nicolas.ferre at atmel.com
Wed Mar 13 06:29:13 EDT 2013


On 03/13/2013 11:25 AM, Ludovic Desroches :
> On Tue, Mar 12, 2013 at 05:54:46PM +0100, Richard Genoud wrote:
>> i2c-gpio is sometimes used in place of i2c-at91.
>> This adds the pin muxes for the gpios.
>>
>> Signed-off-by: Richard Genoud <richard.genoud at gmail.com>
> 
> Since i2c-gpio nodes are already in the a91sam9x5 why not adding pin muxes.
> If not, we should remove these nodes but I think it is quite convenient to keep them in order to easily switch from i2c-at91 to i2c-gpio for debug purpose or others.
> 
> Acked-by: Ludovic Desroches <ludovic.desroches at atmel.com>

Agreed, queued to at91-3.10-dt branch.

Thanks.

>> ---
>>  based on v3.9-rc2
>>
>>  arch/arm/boot/dts/at91sam9x5.dtsi |   30 ++++++++++++++++++++++++++++++
>>  1 files changed, 30 insertions(+), 0 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi
>> index 8cbcff4..d18aff5 100644
>> --- a/arch/arm/boot/dts/at91sam9x5.dtsi
>> +++ b/arch/arm/boot/dts/at91sam9x5.dtsi
>> @@ -343,6 +343,30 @@
>>  					};
>>  				};
>>  
>> +				i2c_gpio0 {
>> +					pinctrl_i2c_gpio0: i2c_gpio0-0 {
>> +						atmel,pins =
>> +							<0 30 0x0 0x2	/* PA30 gpio multidrive I2C0 data */
>> +							 0 31 0x0 0x2>;	/* PA31 gpio multidrive I2C0 clock */
>> +					};
>> +				};
>> +
>> +				i2c_gpio1 {
>> +					pinctrl_i2c_gpio1: i2c_gpio1-0 {
>> +						atmel,pins =
>> +							<2 0 0x0 0x2	/* PC0 gpio multidrive I2C1 data */
>> +							 2 1 0x0 0x2>;	/* PC1 gpio multidrive I2C1 clock */
>> +					};
>> +				};
>> +
>> +				i2c_gpio2 {
>> +					pinctrl_i2c_gpio2: i2c_gpio2-0 {
>> +						atmel,pins =
>> +							<1 4 0x0 0x2	/* PB4 gpio multidrive I2C2 data */
>> +							 1 5 0x0 0x2>;	/* PB5 gpio multidrive I2C2 clock */
>> +					};
>> +				};
>> +
>>  				pioA: gpio at fffff400 {
>>  					compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
>>  					reg = <0xfffff400 0x200>;
>> @@ -583,6 +607,8 @@
>>  		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
>>  		#address-cells = <1>;
>>  		#size-cells = <0>;
>> +		pinctrl-names = "default";
>> +		pinctrl-0 = <&pinctrl_i2c_gpio0>;
>>  		status = "disabled";
>>  	};
>>  
>> @@ -596,6 +622,8 @@
>>  		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
>>  		#address-cells = <1>;
>>  		#size-cells = <0>;
>> +		pinctrl-names = "default";
>> +		pinctrl-0 = <&pinctrl_i2c_gpio1>;
>>  		status = "disabled";
>>  	};
>>  
>> @@ -609,6 +637,8 @@
>>  		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
>>  		#address-cells = <1>;
>>  		#size-cells = <0>;
>> +		pinctrl-names = "default";
>> +		pinctrl-0 = <&pinctrl_i2c_gpio2>;
>>  		status = "disabled";
>>  	};
>>  };
>> -- 
>> 1.7.2.5
>>
>>
>> _______________________________________________
>> linux-arm-kernel mailing list
>> linux-arm-kernel at lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> 
> 


-- 
Nicolas Ferre



More information about the linux-arm-kernel mailing list