[PATCH V3 1/2] ARM: dts: OMAP2+: Add SDMA controller bindings and nodes
Benoit Cousson
b-cousson at ti.com
Tue Mar 12 07:00:51 EDT 2013
+ Seb G.
Hi Jon,
How to you plan to merge that series?
Seb's just posted a McBSP adaptation to SDMA binding, so I'll have to
take this one before being able to merge any other SDMA driver
adaptation patches.
I'm fine to take that one, if you are OK, to avoid merge conflict in DTS
later.
On 02/26/2013 07:27 PM, Jon Hunter wrote:
> Add SDMA controller binding for OMAP2+ devices and populate DMA client
> information for SPI and MMC periperhal on OMAP3+ devices. Please note
typo-------------------------------^
> that OMAP24xx devices do not have SPI and MMC bindings available yet and
> so DMA client information is not populated.
>
> Signed-off-by: Jon Hunter <jon-hunter at ti.com>
> Reviewed-by: Felipe Balbi <balbi at ti.com>
> Acked-by: Santosh Shilimkar <santosh.shilimkar at ti.com>
> Tested-by: Santosh Shilimkar <santosh.shilimkar at ti.com>
> ---
> .../devicetree/bindings/dma/omap-sdma.txt | 51 ++++++++++++++++++++
That's a detail, but the bindings should be introduced along with the
driver DT adaptation since it does represent its "interface".
> arch/arm/boot/dts/omap2.dtsi | 12 +++++
> arch/arm/boot/dts/omap3.dtsi | 40 +++++++++++++++
> arch/arm/boot/dts/omap4.dtsi | 41 ++++++++++++++++
> arch/arm/boot/dts/omap5.dtsi | 41 ++++++++++++++++
> 5 files changed, 185 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/dma/omap-sdma.txt
>
> diff --git a/Documentation/devicetree/bindings/dma/omap-sdma.txt b/Documentation/devicetree/bindings/dma/omap-sdma.txt
> new file mode 100644
> index 0000000..22aab28
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/dma/omap-sdma.txt
> @@ -0,0 +1,51 @@
> +* TI OMAP SDMA controller
> +
> +Required properties:
> +- compatible: Should be set to one of the following:
> +
> + ti,omap2420-sdma (omap2420)
> + ti,omap2430-sdma (omap2430)
> + ti,omap3430-sdma (omap3430)
> + ti,omap3630-sdma (omap3630)
> + ti,omap4430-sdma (omap4430 & omap4460 & omap543x)
> +
> +- reg: Contains DMA registers location and length.
> +- interrupts: Contains DMA interrupt information.
> +- #dma-cells: Must be 1.
> +- #dma-channels: Contains total number of programmable DMA channels.
> +- #dma-requests: Contains total number of DMA requests.
> +
> +Example:
> +
> + sdma: dma-controller at 4A056000 {
> + compatible = "ti,omap-sdma";
> + reg = <0x4A056000 0x1000>;
Nit: you do have several hexa values in upper case, here and in some dts
as well.
Regards,
Benoit
> + interrupts = <0 12 0x4>,
> + <0 13 0x4>,
> + <0 14 0x4>,
> + <0 15 0x4>;
> + #dma-cells = <1>;
> + #dma-channels = <32>;
> + #dma-requests = <127>;
> + };
> +
> +
> +* TI OMAP SDMA clients
> +
> +Required properties:
> +- dmas: List of one or more DMA specifiers, each consisting of
> + - A phandle pointing to DMA controller node
> + - The DMA request number associated with client device
> +- dma-names: Contains one identifier string for each dma specifier in
> + the dmas property. The specific strings that can be used
> + are defined in the binding of the DMA client device.
> +
> +Example:
> +
> + mmc1: mmc at 4809c000 {
> + ...
> + dmas = <&sdma 61>, /* TX channel */
> + <&sdma 62>; /* RX channel */
> + dma-names = "tx", "rx";
> + ...
> + };
> diff --git a/arch/arm/boot/dts/omap2.dtsi b/arch/arm/boot/dts/omap2.dtsi
> index 761c4b6..22dffa0 100644
> --- a/arch/arm/boot/dts/omap2.dtsi
> +++ b/arch/arm/boot/dts/omap2.dtsi
> @@ -49,6 +49,18 @@
> reg = <0x480FE000 0x1000>;
> };
>
> + sdma: dma-controller at 48056000 {
> + compatible = "ti,omap2430-sdma", "ti,omap2420-sdma";
> + reg = <0x48056000 0x1000>;
> + interrupts = <12>,
> + <13>,
> + <14>,
> + <15>;
> + #dma-cells = <1>;
> + #dma-channels = <32>;
> + #dma-requests = <64>;
> + };
> +
> uart1: serial at 4806a000 {
> compatible = "ti,omap2-uart";
> ti,hwmods = "uart1";
> diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
> index 1acc261..4e7acb6 100644
> --- a/arch/arm/boot/dts/omap3.dtsi
> +++ b/arch/arm/boot/dts/omap3.dtsi
> @@ -75,6 +75,18 @@
> reg = <0x48200000 0x1000>;
> };
>
> + sdma: dma-controller at 48056000 {
> + compatible = "ti,omap3630-sdma", "ti,omap3430-sdma";
> + reg = <0x48056000 0x1000>;
> + interrupts = <12>,
> + <13>,
> + <14>,
> + <15>;
> + #dma-cells = <1>;
> + #dma-channels = <32>;
> + #dma-requests = <96>;
> + };
> +
> omap3_pmx_core: pinmux at 48002030 {
> compatible = "ti,omap3-padconf", "pinctrl-single";
> reg = <0x48002030 0x05cc>;
> @@ -192,6 +204,16 @@
> #size-cells = <0>;
> ti,hwmods = "mcspi1";
> ti,spi-num-cs = <4>;
> + dmas = <&sdma 35>,
> + <&sdma 36>,
> + <&sdma 37>,
> + <&sdma 38>,
> + <&sdma 39>,
> + <&sdma 40>,
> + <&sdma 41>,
> + <&sdma 42>;
> + dma-names = "tx0", "rx0", "tx1", "rx1",
> + "tx2", "rx2", "tx3", "rx3";
> };
>
> mcspi2: spi at 4809a000 {
> @@ -200,6 +222,11 @@
> #size-cells = <0>;
> ti,hwmods = "mcspi2";
> ti,spi-num-cs = <2>;
> + dmas = <&sdma 43>,
> + <&sdma 44>,
> + <&sdma 45>,
> + <&sdma 46>;
> + dma-names = "tx0", "rx0", "tx1", "rx1";
> };
>
> mcspi3: spi at 480b8000 {
> @@ -208,6 +235,11 @@
> #size-cells = <0>;
> ti,hwmods = "mcspi3";
> ti,spi-num-cs = <2>;
> + dmas = <&sdma 15>,
> + <&sdma 16>,
> + <&sdma 23>,
> + <&sdma 24>;
> + dma-names = "tx0", "rx0", "tx1", "rx1";
> };
>
> mcspi4: spi at 480ba000 {
> @@ -216,22 +248,30 @@
> #size-cells = <0>;
> ti,hwmods = "mcspi4";
> ti,spi-num-cs = <1>;
> + dmas = <&sdma 70>, <&sdma 71>;
> + dma-names = "tx0", "rx0";
> };
>
> mmc1: mmc at 4809c000 {
> compatible = "ti,omap3-hsmmc";
> ti,hwmods = "mmc1";
> ti,dual-volt;
> + dmas = <&sdma 61>, <&sdma 62>;
> + dma-names = "tx", "rx";
> };
>
> mmc2: mmc at 480b4000 {
> compatible = "ti,omap3-hsmmc";
> ti,hwmods = "mmc2";
> + dmas = <&sdma 47>, <&sdma 48>;
> + dma-names = "tx", "rx";
> };
>
> mmc3: mmc at 480ad000 {
> compatible = "ti,omap3-hsmmc";
> ti,hwmods = "mmc3";
> + dmas = <&sdma 77>, <&sdma 78>;
> + dma-names = "tx", "rx";
> };
>
> wdt2: wdt at 48314000 {
> diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
> index 739bb79..827f6f3 100644
> --- a/arch/arm/boot/dts/omap4.dtsi
> +++ b/arch/arm/boot/dts/omap4.dtsi
> @@ -118,6 +118,18 @@
> pinctrl-single,function-mask = <0x7fff>;
> };
>
> + sdma: dma-controller at 4A056000 {
> + compatible = "ti,omap4430-sdma";
> + reg = <0x4A056000 0x1000>;
> + interrupts = <0 12 0x4>,
> + <0 13 0x4>,
> + <0 14 0x4>,
> + <0 15 0x4>;
> + #dma-cells = <1>;
> + #dma-channels = <32>;
> + #dma-requests = <127>;
> + };
> +
> gpio1: gpio at 4a310000 {
> compatible = "ti,omap4-gpio";
> reg = <0x4a310000 0x200>;
> @@ -260,6 +272,16 @@
> #size-cells = <0>;
> ti,hwmods = "mcspi1";
> ti,spi-num-cs = <4>;
> + dmas = <&sdma 35>,
> + <&sdma 36>,
> + <&sdma 37>,
> + <&sdma 38>,
> + <&sdma 39>,
> + <&sdma 40>,
> + <&sdma 41>,
> + <&sdma 42>;
> + dma-names = "tx0", "rx0", "tx1", "rx1",
> + "tx2", "rx2", "tx3", "rx3";
> };
>
> mcspi2: spi at 4809a000 {
> @@ -270,6 +292,11 @@
> #size-cells = <0>;
> ti,hwmods = "mcspi2";
> ti,spi-num-cs = <2>;
> + dmas = <&sdma 43>,
> + <&sdma 44>,
> + <&sdma 45>,
> + <&sdma 46>;
> + dma-names = "tx0", "rx0", "tx1", "rx1";
> };
>
> mcspi3: spi at 480b8000 {
> @@ -280,6 +307,8 @@
> #size-cells = <0>;
> ti,hwmods = "mcspi3";
> ti,spi-num-cs = <2>;
> + dmas = <&sdma 15>, <&sdma 16>;
> + dma-names = "tx0", "rx0";
> };
>
> mcspi4: spi at 480ba000 {
> @@ -290,6 +319,8 @@
> #size-cells = <0>;
> ti,hwmods = "mcspi4";
> ti,spi-num-cs = <1>;
> + dmas = <&sdma 70>, <&sdma 71>;
> + dma-names = "tx0", "rx0";
> };
>
> mmc1: mmc at 4809c000 {
> @@ -299,6 +330,8 @@
> ti,hwmods = "mmc1";
> ti,dual-volt;
> ti,needs-special-reset;
> + dmas = <&sdma 61>, <&sdma 62>;
> + dma-names = "tx", "rx";
> };
>
> mmc2: mmc at 480b4000 {
> @@ -307,6 +340,8 @@
> interrupts = <0 86 0x4>;
> ti,hwmods = "mmc2";
> ti,needs-special-reset;
> + dmas = <&sdma 47>, <&sdma 48>;
> + dma-names = "tx", "rx";
> };
>
> mmc3: mmc at 480ad000 {
> @@ -315,6 +350,8 @@
> interrupts = <0 94 0x4>;
> ti,hwmods = "mmc3";
> ti,needs-special-reset;
> + dmas = <&sdma 77>, <&sdma 78>;
> + dma-names = "tx", "rx";
> };
>
> mmc4: mmc at 480d1000 {
> @@ -323,6 +360,8 @@
> interrupts = <0 96 0x4>;
> ti,hwmods = "mmc4";
> ti,needs-special-reset;
> + dmas = <&sdma 57>, <&sdma 58>;
> + dma-names = "tx", "rx";
> };
>
> mmc5: mmc at 480d5000 {
> @@ -331,6 +370,8 @@
> interrupts = <0 59 0x4>;
> ti,hwmods = "mmc5";
> ti,needs-special-reset;
> + dmas = <&sdma 59>, <&sdma 60>;
> + dma-names = "tx", "rx";
> };
>
> wdt2: wdt at 4a314000 {
> diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
> index 9e182a9..06d21d6 100644
> --- a/arch/arm/boot/dts/omap5.dtsi
> +++ b/arch/arm/boot/dts/omap5.dtsi
> @@ -108,6 +108,18 @@
> <0x48212000 0x1000>;
> };
>
> + sdma: dma-controller at 4A056000 {
> + compatible = "ti,omap4430-sdma";
> + reg = <0x4A056000 0x1000>;
> + interrupts = <0 12 0x4>,
> + <0 13 0x4>,
> + <0 14 0x4>,
> + <0 15 0x4>;
> + #dma-cells = <1>;
> + #dma-channels = <32>;
> + #dma-requests = <127>;
> + };
> +
> gpio1: gpio at 4ae10000 {
> compatible = "ti,omap4-gpio";
> reg = <0x4ae10000 0x200>;
> @@ -249,6 +261,16 @@
> #size-cells = <0>;
> ti,hwmods = "mcspi1";
> ti,spi-num-cs = <4>;
> + dmas = <&sdma 35>,
> + <&sdma 36>,
> + <&sdma 37>,
> + <&sdma 38>,
> + <&sdma 39>,
> + <&sdma 40>,
> + <&sdma 41>,
> + <&sdma 42>;
> + dma-names = "tx0", "rx0", "tx1", "rx1",
> + "tx2", "rx2", "tx3", "rx3";
> };
>
> mcspi2: spi at 4809a000 {
> @@ -259,6 +281,11 @@
> #size-cells = <0>;
> ti,hwmods = "mcspi2";
> ti,spi-num-cs = <2>;
> + dmas = <&sdma 43>,
> + <&sdma 44>,
> + <&sdma 45>,
> + <&sdma 46>;
> + dma-names = "tx0", "rx0", "tx1", "rx1";
> };
>
> mcspi3: spi at 480b8000 {
> @@ -269,6 +296,8 @@
> #size-cells = <0>;
> ti,hwmods = "mcspi3";
> ti,spi-num-cs = <2>;
> + dmas = <&sdma 15>, <&sdma 16>;
> + dma-names = "tx0", "rx0";
> };
>
> mcspi4: spi at 480ba000 {
> @@ -279,6 +308,8 @@
> #size-cells = <0>;
> ti,hwmods = "mcspi4";
> ti,spi-num-cs = <1>;
> + dmas = <&sdma 70>, <&sdma 71>;
> + dma-names = "tx0", "rx0";
> };
>
> uart1: serial at 4806a000 {
> @@ -336,6 +367,8 @@
> ti,hwmods = "mmc1";
> ti,dual-volt;
> ti,needs-special-reset;
> + dmas = <&sdma 61>, <&sdma 62>;
> + dma-names = "tx", "rx";
> };
>
> mmc2: mmc at 480b4000 {
> @@ -344,6 +377,8 @@
> interrupts = <0 86 0x4>;
> ti,hwmods = "mmc2";
> ti,needs-special-reset;
> + dmas = <&sdma 47>, <&sdma 48>;
> + dma-names = "tx", "rx";
> };
>
> mmc3: mmc at 480ad000 {
> @@ -352,6 +387,8 @@
> interrupts = <0 94 0x4>;
> ti,hwmods = "mmc3";
> ti,needs-special-reset;
> + dmas = <&sdma 77>, <&sdma 78>;
> + dma-names = "tx", "rx";
> };
>
> mmc4: mmc at 480d1000 {
> @@ -360,6 +397,8 @@
> interrupts = <0 96 0x4>;
> ti,hwmods = "mmc4";
> ti,needs-special-reset;
> + dmas = <&sdma 57>, <&sdma 58>;
> + dma-names = "tx", "rx";
> };
>
> mmc5: mmc at 480d5000 {
> @@ -368,6 +407,8 @@
> interrupts = <0 59 0x4>;
> ti,hwmods = "mmc5";
> ti,needs-special-reset;
> + dmas = <&sdma 59>, <&sdma 60>;
> + dma-names = "tx", "rx";
> };
>
> keypad: keypad at 4ae1c000 {
>
More information about the linux-arm-kernel
mailing list