[PATCH 4/4] ARM: at91: introduce SAMA5 support
ludovic.desroches at atmel.com
ludovic.desroches at atmel.com
Fri Mar 8 10:13:58 EST 2013
From: Ludovic Desroches <ludovic.desroches at atmel.com>
This patch introduces the SAMA5 support. It also updates the PMC driver to
manage clock division which is a requirement since some peripherals can't work
at the bus frequency on SAMA5.
Signed-off-by: Ludovic Desroches <ludovic.desroches at atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre at atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj at jcrosoft.com>
---
arch/arm/boot/dts/Makefile | 5 +
arch/arm/boot/dts/sama5d3.dtsi | 1031 ++++++++++++++++++++++++++++
arch/arm/boot/dts/sama5d31ek.dts | 51 ++
arch/arm/boot/dts/sama5d33ek.dts | 44 ++
arch/arm/boot/dts/sama5d34ek.dts | 61 ++
arch/arm/boot/dts/sama5d35ek.dts | 56 ++
arch/arm/boot/dts/sama5d3xcm.dtsi | 91 +++
arch/arm/boot/dts/sama5d3xdm.dtsi | 42 ++
arch/arm/boot/dts/sama5d3xmb.dtsi | 166 +++++
arch/arm/configs/sama5_defconfig | 181 +++++
arch/arm/mach-at91/Kconfig | 34 +
arch/arm/mach-at91/Makefile | 4 +
arch/arm/mach-at91/board-dt-sama5.c | 86 +++
arch/arm/mach-at91/clock.c | 109 ++-
arch/arm/mach-at91/clock.h | 2 +
arch/arm/mach-at91/include/mach/at91_pmc.h | 18 +-
arch/arm/mach-at91/include/mach/cpu.h | 20 +
arch/arm/mach-at91/include/mach/sama5d3.h | 73 ++
arch/arm/mach-at91/sama5d3.c | 377 ++++++++++
arch/arm/mach-at91/setup.c | 27 +
arch/arm/mach-at91/soc.h | 5 +
21 files changed, 2454 insertions(+), 29 deletions(-)
create mode 100644 arch/arm/boot/dts/sama5d3.dtsi
create mode 100644 arch/arm/boot/dts/sama5d31ek.dts
create mode 100644 arch/arm/boot/dts/sama5d33ek.dts
create mode 100644 arch/arm/boot/dts/sama5d34ek.dts
create mode 100644 arch/arm/boot/dts/sama5d35ek.dts
create mode 100644 arch/arm/boot/dts/sama5d3xcm.dtsi
create mode 100644 arch/arm/boot/dts/sama5d3xdm.dtsi
create mode 100644 arch/arm/boot/dts/sama5d3xmb.dtsi
create mode 100644 arch/arm/configs/sama5_defconfig
create mode 100644 arch/arm/mach-at91/board-dt-sama5.c
create mode 100644 arch/arm/mach-at91/include/mach/sama5d3.h
create mode 100644 arch/arm/mach-at91/sama5d3.c
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 9c62558..234e78f 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -31,6 +31,11 @@ dtb-$(CONFIG_ARCH_AT91) += at91sam9g25ek.dtb
dtb-$(CONFIG_ARCH_AT91) += at91sam9g35ek.dtb
dtb-$(CONFIG_ARCH_AT91) += at91sam9x25ek.dtb
dtb-$(CONFIG_ARCH_AT91) += at91sam9x35ek.dtb
+# sama5d3
+dtb-$(CONFIG_ARCH_AT91) += sama5d31ek.dtb
+dtb-$(CONFIG_ARCH_AT91) += sama5d33ek.dtb
+dtb-$(CONFIG_ARCH_AT91) += sama5d34ek.dtb
+dtb-$(CONFIG_ARCH_AT91) += sama5d35ek.dtb
dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-b.dtb
dtb-$(CONFIG_ARCH_BCM) += bcm11351-brt.dtb
diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi
new file mode 100644
index 0000000..39b0458
--- /dev/null
+++ b/arch/arm/boot/dts/sama5d3.dtsi
@@ -0,0 +1,1031 @@
+/*
+ * sama5d3.dtsi - Device Tree Include file for SAMA5D3 family SoC
+ * applies to SAMA5D31, SAMA5D33, SAMA5D34, SAMA5D35 SoC
+ *
+ * Copyright (C) 2013 Atmel,
+ * 2013 Ludovic Desroches <ludovic.desroches at atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/include/ "skeleton.dtsi"
+
+/ {
+ model = "Atmel SAMA5D3 family SoC";
+ compatible = "atmel,sama5d3", "atmel,sama5";
+ interrupt-parent = <&aic>;
+
+ aliases {
+ serial0 = &dbgu;
+ serial1 = &usart0;
+ serial2 = &usart1;
+ serial3 = &usart2;
+ serial4 = &usart3;
+ gpio0 = &pioA;
+ gpio1 = &pioB;
+ gpio2 = &pioC;
+ gpio3 = &pioD;
+ gpio4 = &pioE;
+ tcb0 = &tcb0;
+ tcb1 = &tcb1;
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
+ ssc0 = &ssc0;
+ ssc1 = &ssc1;
+ };
+ cpus {
+ cpu at 0 {
+ compatible = "arm,cortex-a5";
+ };
+ };
+
+ memory {
+ reg = <0x20000000 0x8000000>;
+ };
+
+ ahb {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ apb {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ mmc0: mmc at f0000000 {
+ compatible = "atmel,hsmci";
+ reg = <0xf0000000 0x600>;
+ interrupts = <21 4 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_dat4_7>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ spi0: spi at f0004000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "atmel,at91sam9x5-spi";
+ reg = <0xf0004000 0x100>;
+ interrupts = <24 4 3>;
+ cs-gpios = <&pioD 13 0
+ &pioD 14 0 /* conflicts with SCK0 and CANRX0 */
+ &pioD 15 0 /* conflicts with CTS0 and CANTX0 */
+ &pioD 16 0 /* conflicts with RTS0 and PWMFI3 */
+ >;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi0>;
+ status = "disabled";
+ };
+
+ ssc0: ssc at f0008000 {
+ compatible = "atmel,at91sam9g45-ssc";
+ reg = <0xf0008000 0x4000>;
+ interrupts = <38 4 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
+ status = "disabled";
+ };
+
+ can0: can at f000c000 {
+ compatible = "atmel,at91sam9x5-can";
+ reg = <0xf000c000 0x300>;
+ interrupts = <40 4 3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can0_rx_tx>;
+ status = "disabled";
+ };
+
+ tcb0: timer at f0010000 {
+ compatible = "atmel,at91sam9x5-tcb";
+ reg = <0xf0010000 0x100>;
+ interrupts = <26 4 0>;
+ };
+
+ i2c0: i2c at f0014000 {
+ compatible = "atmel,at91sam9x5-i2c";
+ reg = <0xf0014000 0x4000>;
+ interrupts = <18 4 6>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c1: i2c at f0018000 {
+ compatible = "atmel,at91sam9x5-i2c";
+ reg = <0xf0018000 0x4000>;
+ interrupts = <19 4 6>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ usart0: serial at f001c000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xf001c000 0x100>;
+ interrupts = <12 4 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart0>;
+ status = "disabled";
+ };
+
+ usart1: serial at f0020000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xf0020000 0x100>;
+ interrupts = <13 4 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart1>;
+ status = "disabled";
+ };
+
+ macb0: ethernet at f0028000 {
+ compatible = "cnds,pc302-gem", "cdns,gem";
+ reg = <0xf0028000 0x100>;
+ interrupts = <34 4 3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_macb0_data_rgmii &pinctrl_macb0_signal_rgmii>;
+ status = "disabled";
+ };
+
+ isi: isi at f0034000 {
+ compatible = "atmel,at91sam9g45-isi";
+ reg = <0xf0034000 0x4000>;
+ interrupts = <37 4 5>;
+ status = "disabled";
+ };
+
+ mmc1: mmc at f8000000 {
+ compatible = "atmel,hsmci";
+ reg = <0xf8000000 0x600>;
+ interrupts = <22 4 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc2: mmc at f8004000 {
+ compatible = "atmel,hsmci";
+ reg = <0xf8004000 0x600>;
+ interrupts = <23 4 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mmc2_clk_cmd_dat0 &pinctrl_mmc2_dat1_3>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ spi1: spi at f8008000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "atmel,at91sam9x5-spi";
+ reg = <0xf8008000 0x100>;
+ interrupts = <25 4 3>;
+ cs-gpios = <&pioC 25 0
+ &pioC 26 0 /* conflitcs with TWD1 and ISI_D11 */
+ &pioC 27 0 /* conflitcs with TWCK1 and ISI_D10 */
+ &pioC 28 0 /* conflitcs with PWMFI0 and ISI_D9 */
+ >;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi1>;
+ status = "disabled";
+ };
+
+ ssc1: ssc at f800c000 {
+ compatible = "atmel,at91sam9g45-ssc";
+ reg = <0xf800c000 0x4000>;
+ interrupts = <39 4 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>;
+ status = "disabled";
+ };
+
+ can1: can at f8010000 {
+ compatible = "atmel,at91sam9x5-can";
+ reg = <0xf8010000 0x300>;
+ interrupts = <41 4 3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1_rx_tx>;
+ };
+
+ tcb1: timer at f8014000 {
+ compatible = "atmel,at91sam9x5-tcb";
+ reg = <0xf8014000 0x100>;
+ interrupts = <27 4 0>;
+ };
+
+ adc0: adc at f8018000 {
+ compatible = "atmel,at91sam9260-adc";
+ reg = <0xf8018000 0x100>;
+ interrupts = <29 4 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &pinctrl_adc0_adtrg
+ &pinctrl_adc0_ad0
+ &pinctrl_adc0_ad1
+ &pinctrl_adc0_ad2
+ &pinctrl_adc0_ad3
+ &pinctrl_adc0_ad4
+ &pinctrl_adc0_ad5
+ &pinctrl_adc0_ad6
+ &pinctrl_adc0_ad7
+ &pinctrl_adc0_ad8
+ &pinctrl_adc0_ad9
+ &pinctrl_adc0_ad10
+ &pinctrl_adc0_ad11
+ >;
+ atmel,adc-channel-base = <0x50>;
+ atmel,adc-channels-used = <0xfff>;
+ atmel,adc-drdy-mask = <0x1000000>;
+ atmel,adc-num-channels = <12>;
+ atmel,adc-startup-time = <40>;
+ atmel,adc-status-register = <0x30>;
+ atmel,adc-trigger-register = <0xc0>;
+ atmel,adc-use-external;
+ atmel,adc-vref = <3000>;
+ atmel,adc-res = <10 12>;
+ atmel,adc-res-names = "lowres", "highres";
+ status = "disabled";
+
+ trigger at 0 {
+ trigger-name = "external-rising";
+ trigger-value = <0x1>;
+ trigger-external;
+ };
+ trigger at 1 {
+ trigger-name = "external-falling";
+ trigger-value = <0x2>;
+ trigger-external;
+ };
+ trigger at 2 {
+ trigger-name = "external-any";
+ trigger-value = <0x3>;
+ trigger-external;
+ };
+ trigger at 3 {
+ trigger-name = "continuous";
+ trigger-value = <0x6>;
+ };
+ };
+
+ tsadcc: tsadcc at f8018000 {
+ compatible = "atmel,at91sam9x5-tsadcc";
+ reg = <0xf8018000 0x4000>;
+ interrupts = <29 4 5>;
+ atmel,tsadcc_clock = <300000>;
+ atmel,filtering_average = <0x03>;
+ atmel,pendet_debounce = <0x08>;
+ atmel,pendet_sensitivity = <0x02>;
+ atmel,ts_sample_hold_time = <0x0a>;
+ status = "disabled";
+ };
+
+ i2c2: i2c at f801c000 {
+ compatible = "atmel,at91sam9x5-i2c";
+ reg = <0xf801c000 0x4000>;
+ interrupts = <20 4 6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ usart2: serial at f8020000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xf8020000 0x100>;
+ interrupts = <14 4 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart2>;
+ status = "disabled";
+ };
+
+ usart3: serial at f8024000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xf8024000 0x100>;
+ interrupts = <15 4 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart3>;
+ status = "disabled";
+ };
+
+ macb1: ethernet at f802c000 {
+ compatible = "cdns,at32ap7000-macb", "cdns,macb";
+ reg = <0xf802c000 0x100>;
+ interrupts = <35 4 3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_macb1_rmii>;
+ status = "disabled";
+ };
+
+ sha at f8034000 {
+ compatible = "atmel,sam9g46-sha";
+ reg = <0xf8034000 0x100>;
+ interrupts = <42 4 0>;
+ };
+
+ aes at f8038000 {
+ compatible = "atmel,sam9g46-aes";
+ reg = <0xf8038000 0x100>;
+ interrupts = <43 4 0>;
+ };
+
+ tdes at f803c000 {
+ compatible = "atmel,sam9g46-tdes";
+ reg = <0xf803c000 0x100>;
+ interrupts = <44 4 0>;
+ };
+
+ dma0: dma-controller at ffffe600 {
+ compatible = "atmel,at91sam9g45-dma";
+ reg = <0xffffe600 0x200>;
+ interrupts = <30 4 0>;
+ #dma-cells = <1>;
+ };
+
+ dma1: dma-controller at ffffe800 {
+ compatible = "atmel,at91sam9g45-dma";
+ reg = <0xffffe800 0x200>;
+ interrupts = <31 4 0>;
+ #dma-cells = <1>;
+ };
+
+ ramc0: ramc at ffffea00 {
+ compatible = "atmel,at91sam9g45-ddramc";
+ reg = <0xffffea00 0x200>;
+ };
+
+ dbgu: serial at ffffee00 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xffffee00 0x200>;
+ interrupts = <2 4 7>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_dbgu>;
+ status = "disabled";
+ };
+
+ aic: interrupt-controller at fffff000 {
+ #interrupt-cells = <3>;
+ compatible = "atmel,sama5d3-aic";
+ interrupt-controller;
+ reg = <0xfffff000 0x200>;
+ atmel,external-irqs = <47>;
+ };
+
+ pinctrl at fffff200 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "atmel,at91sam9x5-pinctrl", "atmel,at91rm9200-pinctrl", "simple-bus";
+ ranges = <0xfffff200 0xfffff200 0xa00>;
+ atmel,mux-mask = <
+ /* A B C */
+ 0xffffffff 0xc0fc0000 0xc0ff0000 /* pioA */
+ 0xffffffff 0x0ff8ffff 0x00000000 /* pioB */
+ 0xffffffff 0xbc00f1ff 0x7c00fc00 /* pioC */
+ 0xffffffff 0xc001c0e0 0x0001c1e0 /* pioD */
+ 0xffffffff 0xbf9f8000 0x18000000 /* pioE */
+ >;
+
+ /* shared pinctrl settings */
+ adc0 {
+ pinctrl_adc0_adtrg: adc0_adtrg {
+ atmel,pins =
+ <3 19 0x1 0x0>; /* PD19 periph A ADTRG */
+ };
+ pinctrl_adc0_ad0: adc0_ad0 {
+ atmel,pins =
+ <3 20 0x1 0x0>; /* PD20 periph A AD0 */
+ };
+ pinctrl_adc0_ad1: adc0_ad1 {
+ atmel,pins =
+ <3 21 0x1 0x0>; /* PD21 periph A AD1 */
+ };
+ pinctrl_adc0_ad2: adc0_ad2 {
+ atmel,pins =
+ <3 22 0x1 0x0>; /* PD22 periph A AD2 */
+ };
+ pinctrl_adc0_ad3: adc0_ad3 {
+ atmel,pins =
+ <3 23 0x1 0x0>; /* PD23 periph A AD3 */
+ };
+ pinctrl_adc0_ad4: adc0_ad4 {
+ atmel,pins =
+ <3 24 0x1 0x0>; /* PD24 periph A AD4 */
+ };
+ pinctrl_adc0_ad5: adc0_ad5 {
+ atmel,pins =
+ <3 25 0x1 0x0>; /* PD25 periph A AD5 */
+ };
+ pinctrl_adc0_ad6: adc0_ad6 {
+ atmel,pins =
+ <3 26 0x1 0x0>; /* PD26 periph A AD6 */
+ };
+ pinctrl_adc0_ad7: adc0_ad7 {
+ atmel,pins =
+ <3 27 0x1 0x0>; /* PD27 periph A AD7 */
+ };
+ pinctrl_adc0_ad8: adc0_ad8 {
+ atmel,pins =
+ <3 28 0x1 0x0>; /* PD28 periph A AD8 */
+ };
+ pinctrl_adc0_ad9: adc0_ad9 {
+ atmel,pins =
+ <3 29 0x1 0x0>; /* PD29 periph A AD9 */
+ };
+ pinctrl_adc0_ad10: adc0_ad10 {
+ atmel,pins =
+ <3 30 0x1 0x0>; /* PD30 periph A AD10, conflicts with PCK0 */
+ };
+ pinctrl_adc0_ad11: adc0_ad11 {
+ atmel,pins =
+ <3 31 0x1 0x0>; /* PD31 periph A AD11, conflicts with PCK1 */
+ };
+ };
+
+ can0 {
+ pinctrl_can0_rx_tx: can0_rx_tx {
+ atmel,pins =
+ <3 14 0x3 0x0 /* PD14 periph C RX, conflicts with SCK0, SPI0_NPCS1 */
+ 3 15 0x3 0x0>; /* PD15 periph C TX, conflicts with CTS0, SPI0_NPCS2 */
+ };
+ };
+
+ can1 {
+ pinctrl_can1_rx_tx: can1_rx_tx {
+ atmel,pins =
+ <1 14 0x2 0x0 /* PB14 periph B RX, conflicts with GCRS */
+ 1 15 0x2 0x0>; /* PB15 periph B TX, conflicts with GCOL */
+ };
+ };
+
+ dbgu {
+ pinctrl_dbgu: dbgu-0 {
+ atmel,pins =
+ <1 30 0x1 0x0 /* PB30 periph A */
+ 1 31 0x1 0x1>; /* PB31 periph A with pullup */
+ };
+ };
+
+ i2c0 {
+ pinctrl_i2c0: i2c0-0 {
+ atmel,pins =
+ <0 30 0x1 0x0 /* PA30 periph A TWD0 pin, conflicts with URXD1, ISI_VSYNC */
+ 0 31 0x1 0x0>; /* PA31 periph A TWCK0 pin, conflicts with UTXD1, ISI_HSYNC */
+ };
+ };
+
+ i2c1 {
+ pinctrl_i2c1: i2c1-0 {
+ atmel,pins =
+ <2 26 0x2 0x0 /* PC26 periph B TWD1 pin, conflicts with SPI1_NPCS1, ISI_D11 */
+ 2 27 0x2 0x0>; /* PC27 periph B TWCK1 pin, conflicts with SPI1_NPCS2, ISI_D10 */
+ };
+ };
+
+ isi {
+ pinctrl_isi: isi-0 {
+ atmel,pins =
+ <0 16 0x3 0x0 /* PA16 periph C ISI_D0, conflicts with LCDDAT16 */
+ 0 17 0x3 0x0 /* PA17 periph C ISI_D1, conflicts with LCDDAT17 */
+ 0 18 0x3 0x0 /* PA18 periph C ISI_D2, conflicts with LCDDAT18, TWD2 */
+ 0 19 0x3 0x0 /* PA19 periph C ISI_D3, conflicts with LCDDAT19, TWCK2 */
+ 0 20 0x3 0x0 /* PA20 periph C ISI_D4, conflicts with LCDDAT20, PWMH0 */
+ 0 21 0x3 0x0 /* PA21 periph C ISI_D5, conflicts with LCDDAT21, PWML0 */
+ 0 22 0x3 0x0 /* PA22 periph C ISI_D6, conflicts with LCDDAT22, PWMH1 */
+ 0 23 0x3 0x0 /* PA23 periph C ISI_D7, conflicts with LCDDAT23, PWML1 */
+ 2 30 0x3 0x0 /* PC30 periph C ISI_PCK, conflicts with UTXD0 */
+ 0 31 0x3 0x0 /* PA31 periph C ISI_HSYNC, conflicts with TWCK0, UTXD1 */
+ 0 30 0x3 0x0 /* PA30 periph C ISI_VSYNC, conflicts with TWD0, URXD1 */
+ 2 29 0x3 0x0 /* PC29 periph C ISI_PD8, conflicts with URXD0, PWMFI2 */
+ 2 28 0x3 0x0>; /* PC28 periph C ISI_PD9, conflicts with SPI1_NPCS3, PWMFI0 */
+ };
+ pinctrl_isi_pck_as_mck: isi_pck_as_mck-0 {
+ atmel,pins =
+ <3 31 0x2 0x0>; /* PD31 periph B ISI_MCK */
+ };
+ };
+
+ lcd {
+ pinctrl_lcd: lcd-0 {
+ atmel,pins =
+ <0 24 0x1 0x0 /* PA24 periph A LCDPWM */
+ 0 26 0x1 0x0 /* PA26 periph A LCDVSYNC */
+ 0 27 0x1 0x0 /* PA27 periph A LCDHSYNC */
+ 0 25 0x1 0x0 /* PA25 periph A LCDDISP */
+ 0 29 0x1 0x0 /* PA29 periph A LCDDEN */
+ 0 28 0x1 0x0 /* PA28 periph A LCDPCK */
+ 0 0 0x1 0x0 /* PA0 periph A LCDD0 pin */
+ 0 1 0x1 0x0 /* PA1 periph A LCDD1 pin */
+ 0 2 0x1 0x0 /* PA2 periph A LCDD2 pin */
+ 0 3 0x1 0x0 /* PA3 periph A LCDD3 pin */
+ 0 4 0x1 0x0 /* PA4 periph A LCDD4 pin */
+ 0 5 0x1 0x0 /* PA5 periph A LCDD5 pin */
+ 0 6 0x1 0x0 /* PA6 periph A LCDD6 pin */
+ 0 7 0x1 0x0 /* PA7 periph A LCDD7 pin */
+ 0 8 0x1 0x0 /* PA8 periph A LCDD8 pin */
+ 0 9 0x1 0x0 /* PA9 periph A LCDD9 pin */
+ 0 10 0x1 0x0 /* PA10 periph A LCDD10 pin */
+ 0 11 0x1 0x0 /* PA11 periph A LCDD11 pin */
+ 0 12 0x1 0x0 /* PA12 periph A LCDD12 pin */
+ 0 13 0x1 0x0 /* PA13 periph A LCDD13 pin */
+ 0 14 0x1 0x0 /* PA14 periph A LCDD14 pin */
+ 0 15 0x1 0x0 /* PA15 periph A LCDD15 pin */
+ 2 14 0x3 0x0 /* PC14 periph C LCDD16 pin */
+ 2 13 0x3 0x0 /* PC13 periph C LCDD17 pin */
+ 2 12 0x3 0x0 /* PC12 periph C LCDD18 pin */
+ 2 11 0x3 0x0 /* PC11 periph C LCDD19 pin */
+ 2 10 0x3 0x0 /* PC10 periph C LCDD20 pin */
+ 2 15 0x3 0x0 /* PC15 periph C LCDD21 pin */
+ 4 27 0x3 0x0 /* PE27 periph C LCDD22 pin */
+ 4 28 0x3 0x0>; /* PE28 periph C LCDD23 pin */
+ };
+ };
+
+ macb0 {
+ pinctrl_macb0_data_rgmii: macb0_data_rgmii {
+ atmel,pins =
+ <1 0 0x1 0x0 /* PB0 periph A GTX0, conflicts with PWMH0 */
+ 1 1 0x1 0x0 /* PB1 periph A GTX1, conflicts with PWML0 */
+ 1 2 0x1 0x0 /* PB2 periph A GTX2, conflicts with TK1 */
+ 1 3 0x1 0x0 /* PB3 periph A GTX3, conflicts with TF1 */
+ 1 4 0x1 0x0 /* PB4 periph A GRX0, conflicts with PWMH1 */
+ 1 5 0x1 0x0 /* PB5 periph A GRX1, conflicts with PWML1 */
+ 1 6 0x1 0x0 /* PB6 periph A GRX2, conflicts with TD1 */
+ 1 7 0x1 0x0>; /* PB7 periph A GRX3, conflicts with RK1 */
+ };
+ pinctrl_macb0_data_gmii: macb0_data_gmii {
+ atmel,pins =
+ <1 19 0x2 0x0 /* PB19 periph B GTX4, conflicts with MCI1_CDA */
+ 1 20 0x2 0x0 /* PB20 periph B GTX5, conflicts with MCI1_DA0 */
+ 1 21 0x2 0x0 /* PB21 periph B GTX6, conflicts with MCI1_DA1 */
+ 1 22 0x2 0x0 /* PB22 periph B GTX7, conflicts with MCI1_DA2 */
+ 1 23 0x2 0x0 /* PB23 periph B GRX4, conflicts with MCI1_DA3 */
+ 1 24 0x2 0x0 /* PB24 periph B GRX5, conflicts with MCI1_CK */
+ 1 25 0x2 0x0 /* PB25 periph B GRX6, conflicts with SCK1 */
+ 1 26 0x2 0x0>; /* PB26 periph B GRX7, conflicts with CTS1 */
+ };
+ pinctrl_macb0_signal_rgmii: macb0_signal_rgmii {
+ atmel,pins =
+ <1 8 0x1 0x0 /* PB8 periph A GTXCK, conflicts with PWMH2 */
+ 1 9 0x1 0x0 /* PB9 periph A GTXEN, conflicts with PWML2 */
+ 1 11 0x1 0x0 /* PB11 periph A GRXCK, conflicts with RD1 */
+ 1 13 0x1 0x0 /* PB13 periph A GRXER, conflicts with PWML3 */
+ 1 16 0x1 0x0 /* PB16 periph A GMDC */
+ 1 17 0x1 0x0 /* PB17 periph A GMDIO */
+ 1 18 0x1 0x0>; /* PB18 periph A G125CK */
+ };
+ pinctrl_macb0_signal_gmii: macb0_signal_gmii {
+ atmel,pins =
+ <1 9 0x1 0x0 /* PB9 periph A GTXEN, conflicts with PWML2 */
+ 1 10 0x1 0x0 /* PB10 periph A GTXER, conflicts with RF1 */
+ 1 11 0x1 0x0 /* PB11 periph A GRXCK, conflicts with RD1 */
+ 1 12 0x1 0x0 /* PB12 periph A GRXDV, conflicts with PWMH3 */
+ 1 13 0x1 0x0 /* PB13 periph A GRXER, conflicts with PWML3 */
+ 1 14 0x1 0x0 /* PB14 periph A GCRS, conflicts with CANRX1 */
+ 1 15 0x1 0x0 /* PB15 periph A GCOL, conflicts with CANTX1 */
+ 1 16 0x1 0x0 /* PB16 periph A GMDC */
+ 1 17 0x1 0x0 /* PB17 periph A GMDIO */
+ 1 27 0x2 0x0>; /* PB27 periph B G125CKO */
+ };
+
+ };
+
+ macb1 {
+ pinctrl_macb1_rmii: macb1_rmii-0 {
+ atmel,pins =
+ <2 0 0x1 0x0 /* PC0 periph A ETX0, conflicts with TIOA3 */
+ 2 1 0x1 0x0 /* PC1 periph A ETX1, conflicts with TIOB3 */
+ 2 2 0x1 0x0 /* PC2 periph A ERX0, conflicts with TCLK3 */
+ 2 3 0x1 0x0 /* PC3 periph A ERX1, conflicts with TIOA4 */
+ 2 4 0x1 0x0 /* PC4 periph A ETXEN, conflicts with TIOB4 */
+ 2 5 0x1 0x0 /* PC5 periph A ECRSDV,conflicts with TCLK4 */
+ 2 6 0x1 0x0 /* PC6 periph A ERXER, conflicts with TIOA5 */
+ 2 7 0x1 0x0 /* PC7 periph A EREFCK, conflicts with TIOB5 */
+ 2 8 0x1 0x0 /* PC8 periph A EMDC, conflicts with TCLK5 */
+ 2 9 0x1 0x0>; /* PC9 periph A EMDIO */
+ };
+ };
+
+ mmc0 {
+ pinctrl_mmc0_clk_cmd_dat0: mmc0_clk_cmd_dat0 {
+ atmel,pins =
+ <3 9 0x1 0x0 /* PD9 periph A MCI0_CK */
+ 3 0 0x1 0x1 /* PD0 periph A MCI0_CDA with pullup */
+ 3 1 0x1 0x1>; /* PD1 periph A MCI0_DA0 with pullup */
+ };
+ pinctrl_mmc0_dat1_3: mmc0_dat1_3 {
+ atmel,pins =
+ <3 2 0x1 0x1 /* PD2 periph A MCI0_DA1 with pullup */
+ 3 3 0x1 0x1 /* PD3 periph A MCI0_DA2 with pullup */
+ 3 4 0x1 0x1>; /* PD4 periph A MCI0_DA3 with pullup */
+ };
+ pinctrl_mmc0_dat4_7: mmc0_dat4_7 {
+ atmel,pins =
+ <3 5 0x1 0x1 /* PD5 periph A MCI0_DA4 with pullup, conflicts with TIOA0, PWMH2 */
+ 3 6 0x1 0x1 /* PD6 periph A MCI0_DA5 with pullup, conflicts with TIOB0, PWML2 */
+ 3 7 0x1 0x1 /* PD7 periph A MCI0_DA6 with pullup, conlicts with TCLK0, PWMH3 */
+ 3 8 0x1 0x1>; /* PD8 periph A MCI0_DA7 with pullup, conflicts with PWML3 */
+ };
+ };
+
+ mmc1 {
+ pinctrl_mmc1_clk_cmd_dat0: mmc1_clk_cmd_dat0 {
+ atmel,pins =
+ <1 24 0x1 0x0 /* PB24 periph A MCI1_CK, conflicts with GRX5 */
+ 1 19 0x1 0x1 /* PB19 periph A MCI1_CDA with pullup, conflicts with GTX4 */
+ 1 20 0x1 0x1>; /* PB20 periph A MCI1_DA0 with pullup, conflicts with GTX5 */
+ };
+ pinctrl_mmc1_dat1_3: mmc1_dat1_3 {
+ atmel,pins =
+ <1 21 0x1 0x1 /* PB21 periph A MCI1_DA1 with pullup, conflicts with GTX6 */
+ 1 22 0x1 0x1 /* PB22 periph A MCI1_DA2 with pullup, conflicts with GTX7 */
+ 1 23 0x1 0x1>; /* PB23 periph A MCI1_DA3 with pullup, conflicts with GRX4 */
+ };
+ };
+
+ mmc2 {
+ pinctrl_mmc2_clk_cmd_dat0: mmc2_clk_cmd_dat0 {
+ atmel,pins =
+ <2 15 0x1 0x0 /* PC15 periph A MCI2_CK, conflicts with PCK2 */
+ 2 10 0x1 0x1 /* PC10 periph A MCI2_CDA with pullup */
+ 2 11 0x1 0x1>; /* PC11 periph A MCI2_DA0 with pullup */
+ };
+ pinctrl_mmc2_dat1_3: mmc2_dat1_3 {
+ atmel,pins =
+ <2 12 0x1 0x0 /* PC12 periph A MCI2_DA1 with pullup, conflicts with TIOA1 */
+ 2 13 0x1 0x0 /* PC13 periph A MCI2_DA2 with pullup, conflicts with TIOB1 */
+ 2 14 0x1 0x0>; /* PC14 periph A MCI2_DA3 with pullup, conflicts with TCLK1 */
+ };
+ };
+
+ nand0 {
+ pinctrl_nand0_ale_cle: nand0_ale_cle-0 {
+ atmel,pins =
+ <4 21 0x1 0x1 /* PE21 periph A with pullup */
+ 4 22 0x1 0x1>; /* PE22 periph A with pullup */
+ };
+ };
+
+ pioA: gpio at fffff200 {
+ compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+ reg = <0xfffff200 0x100>;
+ interrupts = <6 4 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ pioB: gpio at fffff400 {
+ compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+ reg = <0xfffff400 0x100>;
+ interrupts = <7 4 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ pioC: gpio at fffff600 {
+ compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+ reg = <0xfffff600 0x100>;
+ interrupts = <8 4 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ pioD: gpio at fffff800 {
+ compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+ reg = <0xfffff800 0x100>;
+ interrupts = <9 4 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ pioE: gpio at fffffa00 {
+ compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+ reg = <0xfffffa00 0x100>;
+ interrupts = <10 4 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ spi0 {
+ pinctrl_spi0: spi0-0 {
+ atmel,pins =
+ <3 10 0x1 0x0 /* PD10 periph A SPI0_MISO pin */
+ 3 11 0x1 0x0 /* PD11 periph A SPI0_MOSI pin */
+ 3 12 0x1 0x0 /* PD12 periph A SPI0_SPCK pin */
+ 3 13 0x0 0x0>; /* PD13 GPIO SPI0_NPCS0 pin */
+ };
+ };
+
+ spi1 {
+ pinctrl_spi1: spi1-0 {
+ atmel,pins =
+ <2 22 0x1 0x0 /* PC22 periph A SPI1_MISO pin */
+ 2 23 0x1 0x0 /* PC23 periph A SPI1_MOSI pin */
+ 2 24 0x1 0x0 /* PC24 periph A SPI1_SPCK pin */
+ 2 25 0x0 0x0>; /* PC25 GPIO SPI1_NPCS0 pin */
+ };
+ };
+
+ ssc0 {
+ pinctrl_ssc0_tx: ssc0_tx {
+ atmel,pins =
+ <2 16 0x1 0x0 /* PC16 periph A TK0 */
+ 2 17 0x1 0x0 /* PC17 periph A TF0 */
+ 2 18 0x1 0x0>; /* PC18 periph A TD0 */
+ };
+
+ pinctrl_ssc0_rx: ssc0_rx {
+ atmel,pins =
+ <2 19 0x1 0x0 /* PC19 periph A RK0 */
+ 2 20 0x1 0x0 /* PC20 periph A RF0 */
+ 2 21 0x1 0x0>; /* PC21 periph A RD0 */
+ };
+ };
+
+ ssc1 {
+ pinctrl_ssc1_tx: ssc1_tx {
+ atmel,pins =
+ <1 2 0x2 0x0 /* PB2 periph B TK1, conflicts with GTX2 */
+ 1 3 0x2 0x0 /* PB3 periph B TF1, conflicts with GTX3 */
+ 1 6 0x2 0x0>; /* PB6 periph B TD1, conflicts with TD1 */
+ };
+
+ pinctrl_ssc1_rx: ssc1_rx {
+ atmel,pins =
+ <1 7 0x2 0x0 /* PB7 periph B RK1, conflicts with EREFCK */
+ 1 10 0x2 0x0 /* PB10 periph B RF1, conflicts with GTXER */
+ 1 11 0x2 0x0>; /* PB11 periph B RD1, conflicts with GRXCK */
+ };
+ };
+
+ uart0 {
+ pinctrl_uart0: uart0-0 {
+ atmel,pins =
+ <2 29 0x1 0x0 /* PC29 periph A, conflicts with PWMFI2, ISI_D8 */
+ 2 30 0x1 0x1>; /* PC30 periph A with pullup, conflicts with ISI_PCK */
+ };
+ };
+
+ uart1 {
+ pinctrl_uart1: uart1-0 {
+ atmel,pins =
+ <0 30 0x2 0x0 /* PA30 periph B, conflicts with TWD0, ISI_VSYNC */
+ 0 31 0x2 0x1>; /* PA31 periph B with pullup, conflicts with TWCK0, ISI_HSYNC */
+ };
+ };
+
+ usart0 {
+ pinctrl_usart0: usart0-0 {
+ atmel,pins =
+ <3 17 0x1 0x0 /* PD17 periph A */
+ 3 18 0x1 0x1>; /* PD18 periph A with pullup */
+ };
+
+ pinctrl_usart0_rts_cts: usart0_rts_cts-0 {
+ atmel,pins =
+ <3 15 0x1 0x0 /* PD15 periph A, conflicts with SPI0_NPCS2, CANTX0 */
+ 3 16 0x1 0x0>; /* PD16 periph A, conflicts with SPI0_NPCS3, PWMFI3 */
+ };
+ };
+
+ usart1 {
+ pinctrl_usart1: usart1-0 {
+ atmel,pins =
+ <1 28 0x1 0x0 /* PB28 periph A */
+ 1 29 0x1 0x1>; /* PB29 periph A with pullup */
+ };
+
+ pinctrl_usart1_rts_cts: usart1_rts_cts-0 {
+ atmel,pins =
+ <1 26 0x1 0x0 /* PB26 periph A, conflicts with GRX7 */
+ 1 27 0x1 0x0>; /* PB27 periph A, conflicts with G125CKO */
+ };
+ };
+
+ usart2 {
+ pinctrl_usart2: usart2-0 {
+ atmel,pins =
+ <4 25 0x2 0x0 /* PE25 periph B, conflicts with A25 */
+ 4 26 0x2 0x1>; /* PE26 periph B with pullup, conflicts NCS0 */
+ };
+
+ pinctrl_usart2_rts_cts: usart2_rts_cts-0 {
+ atmel,pins =
+ <4 23 0x2 0x0 /* PE23 periph B, conflicts with A23 */
+ 4 24 0x2 0x0>; /* PE24 periph B, conflicts with A24 */
+ };
+ };
+
+ usart3 {
+ pinctrl_usart3: usart3-0 {
+ atmel,pins =
+ <4 18 0x2 0x0 /* PE18 periph B, conflicts with A18 */
+ 4 19 0x2 0x1>; /* PE19 periph B with pullup, conflicts with A19 */
+ };
+
+ pinctrl_usart3_rts_cts: usart3_rts_cts-0 {
+ atmel,pins =
+ <4 16 0x2 0x0 /* PE16 periph B, conflicts with A16 */
+ 4 17 0x2 0x0>; /* PE17 periph B, conflicts with A17 */
+ };
+ };
+ };
+
+ pmc: pmc at fffffc00 {
+ compatible = "atmel,at91rm9200-pmc";
+ reg = <0xfffffc00 0x120>;
+ };
+
+ rstc at fffffe00 {
+ compatible = "atmel,at91sam9g45-rstc";
+ reg = <0xfffffe00 0x10>;
+ };
+
+ pit: timer at fffffe30 {
+ compatible = "atmel,at91sam9260-pit";
+ reg = <0xfffffe30 0xf>;
+ interrupts = <3 4 5>;
+ };
+
+ watchdog at fffffe40 {
+ compatible = "atmel,at91sam9260-wdt";
+ reg = <0xfffffe40 0x10>;
+ status = "disabled";
+ };
+
+ rtc at fffffeb0 {
+ compatible = "atmel,at91rm9200-rtc";
+ reg = <0xfffffeb0 0x30>;
+ interrupts = <1 4 7>;
+ };
+ };
+
+ usb0: gadget at 00500000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "atmel,at91sam9rl-udc";
+ reg = <0x00500000 0x100000
+ 0xf8030000 0x4000>;
+ interrupts = <33 4 2>;
+ status = "disabled";
+
+ ep0 {
+ reg = <0>;
+ atmel,fifo-size = <64>;
+ atmel,nb-banks = <1>;
+ };
+
+ ep1 {
+ reg = <1>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <3>;
+ atmel,can-dma;
+ atmel,can-isoc;
+ };
+
+ ep2 {
+ reg = <2>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <3>;
+ atmel,can-dma;
+ atmel,can-isoc;
+ };
+
+ ep3 {
+ reg = <3>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ atmel,can-dma;
+ };
+
+ ep4 {
+ reg = <4>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ atmel,can-dma;
+ };
+
+ ep5 {
+ reg = <5>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ atmel,can-dma;
+ };
+
+ ep6 {
+ reg = <6>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ atmel,can-dma;
+ };
+
+ ep7 {
+ reg = <7>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ atmel,can-dma;
+ };
+
+ ep8 {
+ reg = <8>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ };
+
+ ep9 {
+ reg = <9>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ };
+
+ ep10 {
+ reg = <10>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ };
+
+ ep11 {
+ reg = <11>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ };
+
+ ep12 {
+ reg = <12>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ };
+
+ ep13 {
+ reg = <13>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ };
+
+ ep14 {
+ reg = <14>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ };
+
+ ep15 {
+ reg = <15>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ };
+ };
+
+ usb1: ohci at 00600000 {
+ compatible = "atmel,at91rm9200-ohci", "usb-ohci";
+ reg = <0x00600000 0x100000>;
+ interrupts = <32 4 2>;
+ status = "disabled";
+ };
+
+ usb2: ehci at 00700000 {
+ compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
+ reg = <0x00700000 0x100000>;
+ interrupts = <32 4 2>;
+ status = "disabled";
+ };
+
+ nand0: nand at 60000000 {
+ compatible = "atmel,at91rm9200-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = < 0x60000000 0x01000000 /* EBI CS3 */
+ 0xffffc070 0x00000490 /* SMC PMECC regs */
+ 0xffffc500 0x00000100 /* SMC PMECC Error Location regs */
+ 0x00100000 0x00100000 /* ROM code */
+ 0x70000000 0x10000000 /* NFC Command Registers */
+ 0xffffc000 0x00000070 /* NFC HSMC regs */
+ 0x00200000 0x00100000 /* NFC SRAM banks */
+ >;
+ interrupts = <5 4 6>;
+ atmel,nand-addr-offset = <21>;
+ atmel,nand-cmd-offset = <22>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_nand0_ale_cle>;
+ atmel,pmecc-lookup-table-offset = <0x10000 0x18000>;
+ status = "disabled";
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/sama5d31ek.dts b/arch/arm/boot/dts/sama5d31ek.dts
new file mode 100644
index 0000000..fa5d216
--- /dev/null
+++ b/arch/arm/boot/dts/sama5d31ek.dts
@@ -0,0 +1,51 @@
+/*
+ * sama5d31ek.dts - Device Tree file for SAMA5D31-EK board
+ *
+ * Copyright (C) 2013 Atmel,
+ * 2013 Ludovic Desroches <ludovic.desroches at atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+/include/ "sama5d3xmb.dtsi"
+/include/ "sama5d3xdm.dtsi"
+
+/ {
+ model = "Atmel SAMA5D31-EK";
+ compatible = "atmel,sama5d31ek", "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";
+
+ ahb {
+ apb {
+ spi0: spi at f0004000 {
+ status = "okay";
+ };
+
+ ssc0: ssc at f0008000 {
+ status = "okay";
+ };
+
+ i2c0: i2c at f0014000 {
+ status = "okay";
+ };
+
+ i2c1: i2c at f0018000 {
+ status = "okay";
+ };
+
+ macb1: ethernet at f802c000 {
+ status = "okay";
+ };
+ };
+ };
+
+ leds {
+ d3 {
+ label = "d3";
+ gpios = <&pioE 24 0>;
+ };
+ };
+
+ sound {
+ status = "okay";
+ };
+};
diff --git a/arch/arm/boot/dts/sama5d33ek.dts b/arch/arm/boot/dts/sama5d33ek.dts
new file mode 100644
index 0000000..c38c943
--- /dev/null
+++ b/arch/arm/boot/dts/sama5d33ek.dts
@@ -0,0 +1,44 @@
+/*
+ * sama5d33ek.dts - Device Tree file for SAMA5D33-EK board
+ *
+ * Copyright (C) 2013 Atmel,
+ * 2013 Ludovic Desroches <ludovic.desroches at atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+/include/ "sama5d3xmb.dtsi"
+/include/ "sama5d3xdm.dtsi"
+
+/ {
+ model = "Atmel SAMA5D33-EK";
+ compatible = "atmel,sama5d33ek", "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";
+
+ ahb {
+ apb {
+ spi0: spi at f0004000 {
+ status = "okay";
+ };
+
+ ssc0: ssc at f0008000 {
+ status = "okay";
+ };
+
+ i2c0: i2c at f0014000 {
+ status = "okay";
+ };
+
+ i2c1: i2c at f0018000 {
+ status = "okay";
+ };
+
+ macb0: ethernet at f0028000 {
+ status = "okay";
+ };
+ };
+ };
+
+ sound {
+ status = "okay";
+ };
+};
diff --git a/arch/arm/boot/dts/sama5d34ek.dts b/arch/arm/boot/dts/sama5d34ek.dts
new file mode 100644
index 0000000..d2739f8
--- /dev/null
+++ b/arch/arm/boot/dts/sama5d34ek.dts
@@ -0,0 +1,61 @@
+/*
+ * sama5d34ek.dts - Device Tree file for SAMA5D34-EK board
+ *
+ * Copyright (C) 2013 Atmel,
+ * 2013 Ludovic Desroches <ludovic.desroches at atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+/include/ "sama5d3xmb.dtsi"
+/include/ "sama5d3xdm.dtsi"
+
+/ {
+ model = "Atmel SAMA5D34-EK";
+ compatible = "atmel,sama5d34ek", "atmel,sama5ek", "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";
+
+ ahb {
+ apb {
+ spi0: spi at f0004000 {
+ status = "okay";
+ };
+
+ ssc0: ssc at f0008000 {
+ status = "okay";
+ };
+
+ can0: can at f000c000 {
+ status = "okay";
+ };
+
+ i2c0: i2c at f0014000 {
+ status = "okay";
+ };
+
+ i2c1: i2c at f0018000 {
+ status = "okay";
+
+ 24c256 at 50 {
+ compatible = "24c256";
+ reg = <0x50>;
+ pagesize = <64>;
+ };
+ };
+
+ macb0: ethernet at f0028000 {
+ status = "okay";
+ };
+ };
+ };
+
+ leds {
+ d3 {
+ label = "d3";
+ gpios = <&pioE 24 0>;
+ };
+ };
+
+ sound {
+ status = "okay";
+ };
+};
diff --git a/arch/arm/boot/dts/sama5d35ek.dts b/arch/arm/boot/dts/sama5d35ek.dts
new file mode 100644
index 0000000..a488fc4
--- /dev/null
+++ b/arch/arm/boot/dts/sama5d35ek.dts
@@ -0,0 +1,56 @@
+/*
+ * sama5d35ek.dts - Device Tree file for SAMA5D35-EK board
+ *
+ * Copyright (C) 2013 Atmel,
+ * 2013 Ludovic Desroches <ludovic.desroches at atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+/include/ "sama5d3xmb.dtsi"
+
+/ {
+ model = "Atmel SAMA5D35-EK";
+ compatible = "atmel,sama5d35ek", "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";
+
+ ahb {
+ apb {
+ spi0: spi at f0004000 {
+ status = "okay";
+ };
+
+ can0: can at f000c000 {
+ status = "okay";
+ };
+
+ i2c1: i2c at f0018000 {
+ status = "okay";
+ };
+
+ macb0: ethernet at f0028000 {
+ status = "okay";
+ };
+
+ isi: isi at f0034000 {
+ status = "okay";
+ };
+
+ macb1: ethernet at f802c000 {
+ status = "okay";
+ };
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pb_user1 {
+ label = "pb_user1";
+ gpios = <&pioE 27 0>;
+ linux,code = <0x100>;
+ gpio-key,wakeup;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/sama5d3xcm.dtsi b/arch/arm/boot/dts/sama5d3xcm.dtsi
new file mode 100644
index 0000000..1f8ed40
--- /dev/null
+++ b/arch/arm/boot/dts/sama5d3xcm.dtsi
@@ -0,0 +1,91 @@
+/*
+ * sama5d3xcm.dtsi - Device Tree Include file for SAMA5D3x CPU Module
+ *
+ * Copyright (C) 2013 Atmel,
+ * 2013 Ludovic Desroches <ludovic.desroches at atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/include/ "sama5d3.dtsi"
+
+/ {
+ compatible = "atmel,samad3xcm", "atmel,sama5d3", "atmel,sama5";
+
+ chosen {
+ bootargs = "console=ttyS0,115200 rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs";
+ };
+
+ memory {
+ reg = <0x20000000 0x20000000>;
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ main_clock: clock at 0 {
+ compatible = "atmel,osc", "fixed-clock";
+ clock-frequency = <12000000>;
+ };
+ };
+
+ ahb {
+ apb {
+ macb0: ethernet at f0028000 {
+ phy-mode = "rgmii";
+ };
+ };
+
+ nand0: nand at 60000000 {
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ atmel,has-pmecc;
+ atmel,pmecc-cap = <4>;
+ atmel,pmecc-sector-size = <512>;
+ atmel,has-nfc;
+ atmel,use-nfc-sram;
+ nand-on-flash-bbt;
+ status = "okay";
+
+ at91bootstrap at 0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x40000>;
+ };
+
+ bootloader at 40000 {
+ label = "bootloader";
+ reg = <0x40000 0x80000>;
+ };
+
+ bootloaderenv at c0000 {
+ label = "bootloader env";
+ reg = <0xc0000 0xc0000>;
+ };
+
+ dtb at 180000 {
+ label = "device tree";
+ reg = <0x180000 0x80000>;
+ };
+
+ kernel at 200000 {
+ label = "kernel";
+ reg = <0x200000 0x600000>;
+ };
+
+ rootfs at 800000 {
+ label = "rootfs";
+ reg = <0x800000 0x0f800000>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ d2 {
+ label = "d2";
+ gpios = <&pioE 25 1>; /* PE25, conflicts with A25, RXD2 */
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/sama5d3xdm.dtsi b/arch/arm/boot/dts/sama5d3xdm.dtsi
new file mode 100644
index 0000000..4b8830e
--- /dev/null
+++ b/arch/arm/boot/dts/sama5d3xdm.dtsi
@@ -0,0 +1,42 @@
+/*
+ * sama5d3dm.dtsi - Device Tree file for SAMA5 display module
+ *
+ * Copyright (C) 2013 Atmel,
+ * 2013 Ludovic Desroches <ludovic.desroches at atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/ {
+ ahb {
+ apb {
+ i2c1: i2c at f0018000 {
+ qt1070: keyboard at 1b {
+ compatible = "qt1070";
+ reg = <0x1b>;
+ interrupt-parent = <&pioE>;
+ interrupts = <31 0x0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qt1070_irq>;
+ };
+ };
+
+ adc0: adc at f8018000 {
+ status = "disabled";
+ };
+
+ tsadcc: tsadcc at f8018000 {
+ status = "okay";
+ };
+
+ pinctrl at fffff200 {
+ board {
+ pinctrl_qt1070_irq: qt1070_irq {
+ atmel,pins =
+ <4 31 0x0 0x5>; /* PE31 GPIO with pull up deglith */
+ };
+ };
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/sama5d3xmb.dtsi b/arch/arm/boot/dts/sama5d3xmb.dtsi
new file mode 100644
index 0000000..661d7ca
--- /dev/null
+++ b/arch/arm/boot/dts/sama5d3xmb.dtsi
@@ -0,0 +1,166 @@
+/*
+ * sama5d3xmb.dts - Device Tree file for SAMA5D3x mother board
+ *
+ * Copyright (C) 2013 Atmel,
+ * 2013 Ludovic Desroches <ludovic.desroches at atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/include/ "sama5d3xcm.dtsi"
+
+/ {
+ compatible = "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";
+
+ ahb {
+ apb {
+ mmc0: mmc at f0000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
+ status = "okay";
+ slot at 0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioD 17 0>;
+ };
+ };
+
+ spi0: spi at f0004000 {
+ m25p80 at 0 {
+ compatible = "atmel,at25df321a";
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+ };
+ };
+
+ /*
+ * i2c0 conflicts with ISI:
+ * disable it to allow the use of ISI
+ * can not enable audio when i2c0 disabled
+ */
+ i2c0: i2c at f0014000 {
+ wm8904: wm8904 at 1a {
+ compatible = "wm8904";
+ reg = <0x1a>;
+ };
+ };
+
+ usart1: serial at f0020000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
+ status = "okay";
+ };
+
+ isi: isi at f0034000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_isi &pinctrl_isi_pck_as_mck &pinctrl_isi_power &pinctrl_isi_reset>;
+ };
+
+ mmc1: mmc at f8000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
+ status = "okay";
+ slot at 0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioD 18 0>;
+ };
+ };
+
+ adc0: adc at f8018000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &pinctrl_adc0_adtrg
+ &pinctrl_adc0_ad0
+ &pinctrl_adc0_ad1
+ &pinctrl_adc0_ad2
+ &pinctrl_adc0_ad3
+ &pinctrl_adc0_ad4
+ >;
+ status = "okay";
+ };
+
+ macb1: ethernet at f802c000 {
+ phy-mode = "rmii";
+ };
+
+ pinctrl at fffff200 {
+ board {
+ pinctrl_mmc0_cd: mmc0_cd {
+ atmel,pins =
+ <3 17 0x0 0x5>; /* PD17 GPIO with pullup deglitch */
+ };
+
+ pinctrl_mmc1_cd: mmc1_cd {
+ atmel,pins =
+ <3 18 0x0 0x5>; /* PD18 GPIO with pullup deglitch */
+ };
+
+ pinctrl_pck0_as_audio_mck: pck0_as_audio_mck {
+ atmel,pins =
+ <3 30 0x2 0x0>; /* PD30 periph B */
+ };
+
+ pinctrl_isi_reset: isi_reset-0 {
+ atmel,pins =
+ <4 24 0x0 0x0>; /* PE24 gpio */
+ };
+
+ pinctrl_isi_power: isi_power-0 {
+ atmel,pins =
+ <4 29 0x0 0x0>; /* PE29 gpio */
+ };
+
+ pinctrl_usba_vbus: usba_vbus {
+ atmel,pins =
+ <3 29 0x0 0x4>; /* PD29 GPIO with deglitch */
+ };
+ };
+ };
+
+ dbgu: serial at ffffee00 {
+ status = "okay";
+ };
+
+ watchdog at fffffe40 {
+ status = "okay";
+ };
+ };
+
+ usb0: gadget at 00500000 {
+ atmel,vbus-gpio = <&pioD 29 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usba_vbus>;
+ status = "okay";
+ };
+
+ usb1: ohci at 00600000 {
+ num-ports = <3>;
+ atmel,vbus-gpio = <&pioD 25 0
+ &pioD 26 1
+ &pioD 27 1
+ >;
+ status = "okay";
+ };
+
+ usb2: ehci at 00700000 {
+ status = "okay";
+ };
+ };
+
+ sound {
+ compatible = "atmel,sama5d3ek-wm8904";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pck0_as_audio_mck>;
+
+ atmel,model = "wm8904 @ SAMA5D3EK";
+ atmel,audio-routing =
+ "Headphone Jack", "HPOUTL",
+ "Headphone Jack", "HPOUTR",
+ "IN2L", "Line In Jack",
+ "IN2R", "Line In Jack",
+ "IN1L", "Mic";
+
+ atmel,ssc-controller = <&ssc0>;
+ atmel,audio-codec = <&wm8904>;
+ };
+};
diff --git a/arch/arm/configs/sama5_defconfig b/arch/arm/configs/sama5_defconfig
new file mode 100644
index 0000000..4d0dc3c
--- /dev/null
+++ b/arch/arm/configs/sama5_defconfig
@@ -0,0 +1,181 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+CONFIG_IRQ_DOMAIN_DEBUG=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_EMBEDDED=y
+CONFIG_SLAB=y
+CONFIG_MODULES=y
+CONFIG_MODULE_FORCE_LOAD=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+# CONFIG_LBDAF is not set
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+# CONFIG_IOSCHED_CFQ is not set
+CONFIG_ARCH_AT91=y
+CONFIG_SOC_SAM_V7=y
+CONFIG_SOC_SAMA5D3=y
+CONFIG_MACH_SAMA5_DT=y
+CONFIG_AT91_PROGRAMMABLE_CLOCKS=y
+CONFIG_AEABI=y
+# CONFIG_OABI_COMPAT is not set
+CONFIG_UACCESS_WITH_MEMCPY=y
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="console=ttyS0,115200 initrd=0x21100000,25165824 root=/dev/ram0 rw"
+CONFIG_AUTO_ZRELADDR=y
+CONFIG_VFP=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_PM_RUNTIME=y
+CONFIG_PM_DEBUG=y
+CONFIG_PM_ADVANCED_DEBUG=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+# CONFIG_INET_DIAG is not set
+CONFIG_IPV6=y
+# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_BEET is not set
+CONFIG_IPV6_SIT_6RD=y
+CONFIG_CAN=y
+CONFIG_CAN_AT91=y
+CONFIG_CFG80211=y
+CONFIG_MAC80211=y
+CONFIG_MAC80211_LEDS=y
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_STANDALONE is not set
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_M25P80=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_ATMEL=y
+CONFIG_MTD_UBI=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=4
+CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_ATMEL_TCLIB=y
+CONFIG_ATMEL_SSC=y
+CONFIG_EEPROM_AT24=y
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_SCSI_MULTI_LUN=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+CONFIG_MII=y
+CONFIG_MACB=y
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_MICROCHIP is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+CONFIG_MICREL_PHY=y
+# CONFIG_WLAN is not set
+# CONFIG_INPUT_MOUSEDEV is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_QT1070=y
+CONFIG_KEYBOARD_GPIO=y
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_ATMEL_MXT=y
+CONFIG_TOUCHSCREEN_ATMEL_TSADCC=y
+# CONFIG_SERIO is not set
+CONFIG_LEGACY_PTY_COUNT=4
+CONFIG_SERIAL_ATMEL=y
+CONFIG_SERIAL_ATMEL_CONSOLE=y
+CONFIG_HW_RANDOM=y
+CONFIG_I2C=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_AT91=y
+CONFIG_I2C_GPIO=y
+CONFIG_SPI=y
+CONFIG_SPI_ATMEL=y
+CONFIG_SPI_GPIO=y
+CONFIG_GPIO_SYSFS=y
+# CONFIG_HWMON is not set
+CONFIG_SSB=m
+CONFIG_FB=y
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+# CONFIG_LCD_CLASS_DEVICE is not set
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+# CONFIG_BACKLIGHT_GENERIC is not set
+CONFIG_FRAMEBUFFER_CONSOLE=y
+# CONFIG_HID_GENERIC is not set
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_ACM=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_AT91=y
+CONFIG_USB_MASS_STORAGE=m
+CONFIG_MMC=y
+# CONFIG_MMC_BLOCK_BOUNCE is not set
+CONFIG_MMC_ATMELMCI=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_GPIO=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_AT91RM9200=y
+CONFIG_DMADEVICES=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_IIO=y
+CONFIG_AT91_ADC=y
+CONFIG_EXT2_FS=y
+CONFIG_FANOTIFY=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_SUMMARY=y
+CONFIG_UBIFS_FS=y
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_850=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+# CONFIG_SCHED_DEBUG is not set
+CONFIG_DEBUG_MEMORY_INIT=y
+# CONFIG_FTRACE is not set
+CONFIG_DEBUG_USER=y
+CONFIG_DEBUG_LL=y
+CONFIG_EARLY_PRINTK=y
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRYPTO_USER_API_HASH=m
+CONFIG_CRYPTO_USER_API_SKCIPHER=m
+CONFIG_CRYPTO_DEV_ATMEL_AES=y
+CONFIG_CRYPTO_DEV_ATMEL_TDES=y
+CONFIG_CRYPTO_DEV_ATMEL_SHA=y
+CONFIG_CRC_CCITT=m
+CONFIG_CRC_ITU_T=m
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index 8b35c7f..118699a 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -29,6 +29,14 @@ config SOC_AT91SAM9
select MULTI_IRQ_HANDLER
select SPARSE_IRQ
+config SOC_SAMA5
+ bool
+ select AT91_SAM9_TIME
+ select CPU_V7
+ select GENERIC_CLOCKEVENTS
+ select MULTI_IRQ_HANDLER
+ select SPARSE_IRQ
+
menu "Atmel AT91 System-on-Chip"
choice
@@ -41,10 +49,28 @@ config SOC_SAM_V4_V5
Select this if you are using one of Atmel's AT91SAM9, AT91RM9200
or AT91X40 SoC.
+config SOC_SAM_V7
+ bool "Cortex A5"
+ help
+ Select this if you are using one of Atmel's SAMA5D3 SoC.
+
endchoice
comment "Atmel AT91 Processor"
+if SOC_SAM_V7
+config SOC_SAMA5D3
+ bool "SAMA5D3 family"
+ depends on SOC_SAM_V7
+ select SOC_SAMA5
+ select HAVE_FB_ATMEL
+ select HAVE_NET_MACB
+ select HAVE_AT91_DBGU1
+ help
+ Select this if you are using one of Atmel's SAMA5D3 family SoC.
+ This support covers SAMA5D31, SAMA5D33, SAMA5D34, SAMA5D35.
+endif
+
if SOC_SAM_V4_V5
config SOC_AT91RM9200
bool "AT91RM9200"
@@ -134,6 +160,14 @@ config MACH_AT91SAM9_DT
Select this if you want to experiment device-tree with
an Atmel Evaluation Kit.
+config MACH_SAMA5_DT
+ bool "Atmel SAMA5 Evaluation Kits with device-tree support"
+ depends on SOC_SAMA5
+ select USE_OF
+ help
+ Select this if you want to experiment device-tree with
+ an Atmel Evaluation Kit.
+
# ----------------------------------------------------------
comment "AT91 Feature Selections"
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index 74e9b5b..788562d 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -22,6 +22,7 @@ obj-$(CONFIG_SOC_AT91SAM9G45) += at91sam9g45.o
obj-$(CONFIG_SOC_AT91SAM9N12) += at91sam9n12.o
obj-$(CONFIG_SOC_AT91SAM9X5) += at91sam9x5.o
obj-$(CONFIG_SOC_AT91SAM9RL) += at91sam9rl.o
+obj-$(CONFIG_SOC_SAMA5D3) += sama5d3.o
obj-$(CONFIG_ARCH_AT91RM9200) += at91rm9200_devices.o
obj-$(CONFIG_ARCH_AT91SAM9260) += at91sam9260_devices.o
@@ -91,6 +92,9 @@ obj-$(CONFIG_MACH_AT91SAM9M10G45EK) += board-sam9m10g45ek.o
obj-$(CONFIG_MACH_AT91RM9200_DT) += board-dt-rm9200.o
obj-$(CONFIG_MACH_AT91SAM9_DT) += board-dt-sam9.o
+# SAMA5 board with device-tree
+obj-$(CONFIG_MACH_SAMA5_DT) += board-dt-sama5.o
+
# AT91X40 board-specific support
obj-$(CONFIG_MACH_AT91EB01) += board-eb01.o
diff --git a/arch/arm/mach-at91/board-dt-sama5.c b/arch/arm/mach-at91/board-dt-sama5.c
new file mode 100644
index 0000000..705305e
--- /dev/null
+++ b/arch/arm/mach-at91/board-dt-sama5.c
@@ -0,0 +1,86 @@
+/*
+ * Setup code for SAMA5 Evaluation Kits with Device Tree support
+ *
+ * Copyright (C) 2013 Atmel,
+ * 2013 Ludovic Desroches <ludovic.desroches at atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/gpio.h>
+#include <linux/micrel_phy.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/phy.h>
+
+#include <asm/setup.h>
+#include <asm/irq.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include "at91_aic.h"
+#include "generic.h"
+
+
+static const struct of_device_id irq_of_match[] __initconst = {
+
+ { .compatible = "atmel,sama5d3-aic", .data = at91_aic5_of_init },
+ { /*sentinel*/ }
+};
+
+static void __init at91_dt_init_irq(void)
+{
+ of_irq_init(irq_of_match);
+}
+
+static int ksz9021rn_phy_fixup(struct phy_device *phy)
+{
+ int value;
+
+#define GMII_RCCPSR 260
+#define GMII_RRDPSR 261
+#define GMII_ERCR 11
+#define GMII_ERDWR 12
+
+ /* Set delay values */
+ value = GMII_RCCPSR | 0x8000;
+ phy_write(phy, GMII_ERCR, value);
+ value = 0xF2F4;
+ phy_write(phy, GMII_ERDWR, value);
+ value = GMII_RRDPSR | 0x8000;
+ phy_write(phy, GMII_ERCR, value);
+ value = 0x2222;
+ phy_write(phy, GMII_ERDWR, value);
+
+ return 0;
+}
+
+static void __init sama5_dt_device_init(void)
+{
+ if (of_machine_is_compatible("atmel,sama5d3xcm"))
+ phy_register_fixup_for_uid(PHY_ID_KSZ9021, MICREL_PHY_ID_MASK,
+ ksz9021rn_phy_fixup);
+
+ of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
+}
+
+static const char *sama5_dt_board_compat[] __initdata = {
+ "atmel,sama5",
+ NULL
+};
+
+DT_MACHINE_START(sama5_dt, "Atmel SAMA5 (Device Tree)")
+ /* Maintainer: Atmel */
+ .init_time = at91sam926x_pit_init,
+ .map_io = at91_map_io,
+ .handle_irq = at91_aic5_handle_irq,
+ .init_early = at91_dt_initialize,
+ .init_irq = at91_dt_init_irq,
+ .init_machine = sama5_dt_device_init,
+ .dt_compat = sama5_dt_board_compat,
+MACHINE_END
diff --git a/arch/arm/mach-at91/clock.c b/arch/arm/mach-at91/clock.c
index 3336150..da84188 100644
--- a/arch/arm/mach-at91/clock.c
+++ b/arch/arm/mach-at91/clock.c
@@ -54,7 +54,10 @@ EXPORT_SYMBOL_GPL(at91_pmc_base);
*/
#define cpu_has_utmi() ( cpu_is_at91sam9rl() \
|| cpu_is_at91sam9g45() \
- || cpu_is_at91sam9x5())
+ || cpu_is_at91sam9x5() \
+ || cpu_is_sama5d3())
+
+#define cpu_has_1056M_plla() (cpu_is_sama5d3())
#define cpu_has_800M_plla() ( cpu_is_at91sam9g20() \
|| cpu_is_at91sam9g45() \
@@ -75,7 +78,8 @@ EXPORT_SYMBOL_GPL(at91_pmc_base);
|| cpu_is_at91sam9n12()))
#define cpu_has_upll() (cpu_is_at91sam9g45() \
- || cpu_is_at91sam9x5())
+ || cpu_is_at91sam9x5() \
+ || cpu_is_sama5d3())
/* USB host HS & FS */
#define cpu_has_uhp() (!cpu_is_at91sam9rl())
@@ -83,18 +87,22 @@ EXPORT_SYMBOL_GPL(at91_pmc_base);
/* USB device FS only */
#define cpu_has_udpfs() (!(cpu_is_at91sam9rl() \
|| cpu_is_at91sam9g45() \
- || cpu_is_at91sam9x5()))
+ || cpu_is_at91sam9x5() \
+ || cpu_is_sama5d3()))
#define cpu_has_plladiv2() (cpu_is_at91sam9g45() \
|| cpu_is_at91sam9x5() \
- || cpu_is_at91sam9n12())
+ || cpu_is_at91sam9n12() \
+ || cpu_is_sama5d3())
#define cpu_has_mdiv3() (cpu_is_at91sam9g45() \
|| cpu_is_at91sam9x5() \
- || cpu_is_at91sam9n12())
+ || cpu_is_at91sam9n12() \
+ || cpu_is_sama5d3())
#define cpu_has_alt_prescaler() (cpu_is_at91sam9x5() \
- || cpu_is_at91sam9n12())
+ || cpu_is_at91sam9n12() \
+ || cpu_is_sama5d3())
static LIST_HEAD(clocks);
static DEFINE_SPINLOCK(clk_lock);
@@ -210,10 +218,26 @@ struct clk mck = {
static void pmc_periph_mode(struct clk *clk, int is_on)
{
- if (is_on)
- at91_pmc_write(AT91_PMC_PCER, clk->pmc_mask);
- else
- at91_pmc_write(AT91_PMC_PCDR, clk->pmc_mask);
+ u32 regval = 0;
+
+ /*
+ * With sama5d3 devices, we are managing clock division so we have to
+ * use the Peripheral Control Register introduced from at91sam9x5
+ * devices.
+ */
+ if (cpu_is_sama5d3()) {
+ regval |= AT91_PMC_PCR_CMD; /* write command */
+ regval |= clk->pid & AT91_PMC_PCR_PID; /* peripheral selection */
+ regval |= AT91_PMC_PCR_DIV(clk->div);
+ if (is_on)
+ regval |= AT91_PMC_PCR_EN; /* enable clock */
+ at91_pmc_write(AT91_PMC_PCR, regval);
+ } else {
+ if (is_on)
+ at91_pmc_write(AT91_PMC_PCER, clk->pmc_mask);
+ else
+ at91_pmc_write(AT91_PMC_PCDR, clk->pmc_mask);
+ }
}
static struct clk __init *at91_css_to_clk(unsigned long css)
@@ -443,14 +467,18 @@ static void __init init_programmable_clock(struct clk *clk)
static int at91_clk_show(struct seq_file *s, void *unused)
{
- u32 scsr, pcsr, uckr = 0, sr;
+ u32 scsr, pcsr, pcsr1 = 0, uckr = 0, sr;
struct clk *clk;
scsr = at91_pmc_read(AT91_PMC_SCSR);
pcsr = at91_pmc_read(AT91_PMC_PCSR);
+ if (cpu_is_sama5d3())
+ pcsr1 = at91_pmc_read(AT91_PMC_PCSR1);
sr = at91_pmc_read(AT91_PMC_SR);
seq_printf(s, "SCSR = %8x\n", scsr);
seq_printf(s, "PCSR = %8x\n", pcsr);
+ if (cpu_is_sama5d3())
+ seq_printf(s, "PCSR1 = %8x\n", pcsr1);
seq_printf(s, "MOR = %8x\n", at91_pmc_read(AT91_CKGR_MOR));
seq_printf(s, "MCFR = %8x\n", at91_pmc_read(AT91_CKGR_MCFR));
seq_printf(s, "PLLA = %8x\n", at91_pmc_read(AT91_CKGR_PLLAR));
@@ -470,20 +498,30 @@ static int at91_clk_show(struct seq_file *s, void *unused)
list_for_each_entry(clk, &clocks, node) {
char *state;
- if (clk->mode == pmc_sys_mode)
+ if (clk->mode == pmc_sys_mode) {
state = (scsr & clk->pmc_mask) ? "on" : "off";
- else if (clk->mode == pmc_periph_mode)
- state = (pcsr & clk->pmc_mask) ? "on" : "off";
- else if (clk->mode == pmc_uckr_mode)
+ } else if (clk->mode == pmc_periph_mode) {
+ if (cpu_is_sama5d3()) {
+ u32 pmc_mask = 1 << (clk->pid % 32);
+
+ if (clk->pid > 31)
+ state = (pcsr1 & pmc_mask) ? "on" : "off";
+ else
+ state = (pcsr & pmc_mask) ? "on" : "off";
+ } else {
+ state = (pcsr & clk->pmc_mask) ? "on" : "off";
+ }
+ } else if (clk->mode == pmc_uckr_mode) {
state = (uckr & clk->pmc_mask) ? "on" : "off";
- else if (clk->pmc_mask)
+ } else if (clk->pmc_mask) {
state = (sr & clk->pmc_mask) ? "on" : "off";
- else if (clk == &clk32k || clk == &main_clk)
+ } else if (clk == &clk32k || clk == &main_clk) {
state = "on";
- else
+ } else {
state = "";
+ }
- seq_printf(s, "%-10s users=%2d %-3s %9ld Hz %s\n",
+ seq_printf(s, "%-10s users=%2d %-3s %9lu Hz %s\n",
clk->name, clk->users, state, clk_get_rate(clk),
clk->parent ? clk->parent->name : "");
}
@@ -530,6 +568,9 @@ int __init clk_register(struct clk *clk)
if (clk_is_peripheral(clk)) {
if (!clk->parent)
clk->parent = &mck;
+ if (cpu_is_sama5d3())
+ clk->rate_hz = DIV_ROUND_UP(clk->parent->rate_hz,
+ 1 << clk->div);
clk->mode = pmc_periph_mode;
}
else if (clk_is_sys(clk)) {
@@ -555,7 +596,11 @@ static u32 __init at91_pll_rate(struct clk *pll, u32 freq, u32 reg)
unsigned mul, div;
div = reg & 0xff;
- mul = (reg >> 16) & 0x7ff;
+ if (cpu_is_sama5d3())
+ mul = AT91_PMC3_MUL_GET(reg);
+ else
+ mul = AT91_PMC_MUL_GET(reg);
+
if (div && mul) {
freq /= div;
freq *= mul + 1;
@@ -706,12 +751,15 @@ static int __init at91_pmc_init(unsigned long main_clock)
/* report if PLLA is more than mildly overclocked */
plla.rate_hz = at91_pll_rate(&plla, main_clock, at91_pmc_read(AT91_CKGR_PLLAR));
- if (cpu_has_300M_plla()) {
- if (plla.rate_hz > 300000000)
+ if (cpu_has_1056M_plla()) {
+ if (plla.rate_hz > 1056000000)
pll_overclock = true;
} else if (cpu_has_800M_plla()) {
if (plla.rate_hz > 800000000)
pll_overclock = true;
+ } else if (cpu_has_300M_plla()) {
+ if (plla.rate_hz > 300000000)
+ pll_overclock = true;
} else if (cpu_has_240M_plla()) {
if (plla.rate_hz > 240000000)
pll_overclock = true;
@@ -872,6 +920,7 @@ int __init at91_clock_init(unsigned long main_clock)
static int __init at91_clock_reset(void)
{
unsigned long pcdr = 0;
+ unsigned long pcdr1 = 0;
unsigned long scdr = 0;
struct clk *clk;
@@ -879,8 +928,17 @@ static int __init at91_clock_reset(void)
if (clk->users > 0)
continue;
- if (clk->mode == pmc_periph_mode)
- pcdr |= clk->pmc_mask;
+ if (clk->mode == pmc_periph_mode) {
+ if (cpu_is_sama5d3()) {
+ u32 pmc_mask = 1 << (clk->pid % 32);
+
+ if (clk->pid > 31)
+ pcdr1 |= pmc_mask;
+ else
+ pcdr |= pmc_mask;
+ } else
+ pcdr |= clk->pmc_mask;
+ }
if (clk->mode == pmc_sys_mode)
scdr |= clk->pmc_mask;
@@ -888,8 +946,9 @@ static int __init at91_clock_reset(void)
pr_debug("Clocks: disable unused %s\n", clk->name);
}
- at91_pmc_write(AT91_PMC_PCDR, pcdr);
at91_pmc_write(AT91_PMC_SCDR, scdr);
+ if (cpu_is_sama5d3())
+ at91_pmc_write(AT91_PMC_PCDR1, pcdr1);
return 0;
}
diff --git a/arch/arm/mach-at91/clock.h b/arch/arm/mach-at91/clock.h
index c2e63e4..a98a39b 100644
--- a/arch/arm/mach-at91/clock.h
+++ b/arch/arm/mach-at91/clock.h
@@ -20,7 +20,9 @@ struct clk {
const char *name; /* unique clock name */
struct clk_lookup cl;
unsigned long rate_hz;
+ unsigned div; /* parent clock divider */
struct clk *parent;
+ unsigned pid; /* peripheral ID */
u32 pmc_mask;
void (*mode)(struct clk *, int);
unsigned id:3; /* PCK0..4, or 32k/main/a/b */
diff --git a/arch/arm/mach-at91/include/mach/at91_pmc.h b/arch/arm/mach-at91/include/mach/at91_pmc.h
index ea2c57a..31df120 100644
--- a/arch/arm/mach-at91/include/mach/at91_pmc.h
+++ b/arch/arm/mach-at91/include/mach/at91_pmc.h
@@ -75,6 +75,9 @@ extern void __iomem *at91_pmc_base;
#define AT91_PMC_PLLCOUNT (0x3f << 8) /* PLL Counter */
#define AT91_PMC_OUT (3 << 14) /* PLL Clock Frequency Range */
#define AT91_PMC_MUL (0x7ff << 16) /* PLL Multiplier */
+#define AT91_PMC_MUL_GET(n) ((n) >> 16 & 0x7ff)
+#define AT91_PMC3_MUL (0x7f << 18) /* PLL Multiplier [SAMA5 only] */
+#define AT91_PMC3_MUL_GET(n) ((n) >> 18 & 0x7f)
#define AT91_PMC_USBDIV (3 << 28) /* USB Divisor (PLLB only) */
#define AT91_PMC_USBDIV_1 (0 << 28)
#define AT91_PMC_USBDIV_2 (1 << 28)
@@ -167,11 +170,18 @@ extern void __iomem *at91_pmc_base;
#define AT91_PMC_WPVS (0x1 << 0) /* Write Protect Violation Status */
#define AT91_PMC_WPVSRC (0xffff << 8) /* Write Protect Violation Source */
-#define AT91_PMC_PCR 0x10c /* Peripheral Control Register [some SAM9] */
+#define AT91_PMC_PCER1 0x100 /* Peripheral Clock Enable Register 1 [SAMA5 only]*/
+#define AT91_PMC_PCDR1 0x104 /* Peripheral Clock Enable Register 1 */
+#define AT91_PMC_PCSR1 0x108 /* Peripheral Clock Enable Register 1 */
+
+#define AT91_PMC_PCR 0x10c /* Peripheral Control Register [some SAM9 and SAMA5] */
#define AT91_PMC_PCR_PID (0x3f << 0) /* Peripheral ID */
-#define AT91_PMC_PCR_CMD (0x1 << 12) /* Command */
-#define AT91_PMC_PCR_DIV (0x3 << 16) /* Divisor Value */
-#define AT91_PMC_PCRDIV(n) (((n) << 16) & AT91_PMC_PCR_DIV)
+#define AT91_PMC_PCR_CMD (0x1 << 12) /* Command (read=0, write=1) */
+#define AT91_PMC_PCR_DIV(n) ((n) << 16) /* Divisor Value */
+#define AT91_PMC_PCR_DIV0 0x0 /* Peripheral clock is MCK */
+#define AT91_PMC_PCR_DIV2 0x2 /* Peripheral clock is MCK/2 */
+#define AT91_PMC_PCR_DIV4 0x4 /* Peripheral clock is MCK/4 */
+#define AT91_PMC_PCR_DIV8 0x8 /* Peripheral clock is MCK/8 */
#define AT91_PMC_PCR_EN (0x1 << 28) /* Enable */
#endif
diff --git a/arch/arm/mach-at91/include/mach/cpu.h b/arch/arm/mach-at91/include/mach/cpu.h
index b6504c1..0f3379f 100644
--- a/arch/arm/mach-at91/include/mach/cpu.h
+++ b/arch/arm/mach-at91/include/mach/cpu.h
@@ -36,6 +36,8 @@
#define ARCH_ID_AT91M40807 0x14080745
#define ARCH_ID_AT91R40008 0x44000840
+#define ARCH_ID_SAMA5D3 0x8A5C07C0
+
#define ARCH_EXID_AT91SAM9M11 0x00000001
#define ARCH_EXID_AT91SAM9M10 0x00000002
#define ARCH_EXID_AT91SAM9G46 0x00000003
@@ -47,6 +49,11 @@
#define ARCH_EXID_AT91SAM9G25 0x00000003
#define ARCH_EXID_AT91SAM9X25 0x00000004
+#define ARCH_EXID_SAMA5D31 0x00444300
+#define ARCH_EXID_SAMA5D33 0x00414300
+#define ARCH_EXID_SAMA5D34 0x00414301
+#define ARCH_EXID_SAMA5D35 0x00584300
+
#define ARCH_FAMILY_AT91X92 0x09200000
#define ARCH_FAMILY_AT91SAM9 0x01900000
#define ARCH_FAMILY_AT91SAM9XE 0x02900000
@@ -75,6 +82,9 @@ enum at91_soc_type {
/* SAM9N12 */
AT91_SOC_SAM9N12,
+ /* SAMA5D3 */
+ AT91_SOC_SAMA5D3,
+
/* Unknown type */
AT91_SOC_NONE
};
@@ -93,6 +103,10 @@ enum at91_soc_subtype {
AT91_SOC_SAM9G15, AT91_SOC_SAM9G35, AT91_SOC_SAM9X35,
AT91_SOC_SAM9G25, AT91_SOC_SAM9X25,
+ /* SAMA5D3 */
+ AT91_SOC_SAMA5D31, AT91_SOC_SAMA5D33, AT91_SOC_SAMA5D34,
+ AT91_SOC_SAMA5D35,
+
/* Unknown subtype */
AT91_SOC_SUBTYPE_NONE
};
@@ -187,6 +201,12 @@ static inline int at91_soc_is_detected(void)
#define cpu_is_at91sam9n12() (0)
#endif
+#ifdef CONFIG_SOC_SAMA5D3
+#define cpu_is_sama5d3() (at91_soc_initdata.type == AT91_SOC_SAMA5D3)
+#else
+#define cpu_is_sama5d3() (0)
+#endif
+
/*
* Since this is ARM, we will never run on any AVR32 CPU. But these
* definitions may reduce clutter in common drivers.
diff --git a/arch/arm/mach-at91/include/mach/sama5d3.h b/arch/arm/mach-at91/include/mach/sama5d3.h
new file mode 100644
index 0000000..6dc81ee
--- /dev/null
+++ b/arch/arm/mach-at91/include/mach/sama5d3.h
@@ -0,0 +1,73 @@
+/*
+ * Chip-specific header file for the SAMA5D3 family
+ *
+ * Copyright (C) 2013 Atmel,
+ * 2013 Ludovic Desroches <ludovic.desroches at atmel.com>
+ *
+ * Common definitions.
+ * Based on SAMA5D3 datasheet.
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+#ifndef SAMA5D3_H
+#define SAMA5D3_H
+
+/*
+ * Peripheral identifiers/interrupts.
+ */
+#define AT91_ID_FIQ 0 /* Advanced Interrupt Controller (FIQ) */
+#define AT91_ID_SYS 1 /* System Peripherals */
+#define SAMA5D3_ID_DBGU 2 /* debug Unit (usually no special interrupt line) */
+#define AT91_ID_PIT 3 /* PIT */
+#define SAMA5D3_ID_WDT 4 /* Watchdog Timer Interrupt */
+#define SAMA5D3_ID_HSMC 5 /* Static Memory Controller */
+#define SAMA5D3_ID_PIOA 6 /* PIOA */
+#define SAMA5D3_ID_PIOB 7 /* PIOB */
+#define SAMA5D3_ID_PIOC 8 /* PIOC */
+#define SAMA5D3_ID_PIOD 9 /* PIOD */
+#define SAMA5D3_ID_PIOE 10 /* PIOE */
+#define SAMA5D3_ID_SMD 11 /* SMD Soft Modem */
+#define SAMA5D3_ID_USART0 12 /* USART0 */
+#define SAMA5D3_ID_USART1 13 /* USART1 */
+#define SAMA5D3_ID_USART2 14 /* USART2 */
+#define SAMA5D3_ID_USART3 15 /* USART3 */
+#define SAMA5D3_ID_UART0 16 /* UART 0 */
+#define SAMA5D3_ID_UART1 17 /* UART 1 */
+#define SAMA5D3_ID_TWI0 18 /* Two-Wire Interface 0 */
+#define SAMA5D3_ID_TWI1 19 /* Two-Wire Interface 1 */
+#define SAMA5D3_ID_TWI2 20 /* Two-Wire Interface 2 */
+#define SAMA5D3_ID_HSMCI0 21 /* MCI */
+#define SAMA5D3_ID_HSMCI1 22 /* MCI */
+#define SAMA5D3_ID_HSMCI2 23 /* MCI */
+#define SAMA5D3_ID_SPI0 24 /* Serial Peripheral Interface 0 */
+#define SAMA5D3_ID_SPI1 25 /* Serial Peripheral Interface 1 */
+#define SAMA5D3_ID_TC0 26 /* Timer Counter 0 */
+#define SAMA5D3_ID_TC1 27 /* Timer Counter 2 */
+#define SAMA5D3_ID_PWM 28 /* Pulse Width Modulation Controller */
+#define SAMA5D3_ID_ADC 29 /* Touch Screen ADC Controller */
+#define SAMA5D3_ID_DMA0 30 /* DMA Controller 0 */
+#define SAMA5D3_ID_DMA1 31 /* DMA Controller 1 */
+#define SAMA5D3_ID_UHPHS 32 /* USB Host High Speed */
+#define SAMA5D3_ID_UDPHS 33 /* USB Device High Speed */
+#define SAMA5D3_ID_GMAC 34 /* Gigabit Ethernet MAC */
+#define SAMA5D3_ID_EMAC 35 /* Ethernet MAC */
+#define SAMA5D3_ID_LCDC 36 /* LCD Controller */
+#define SAMA5D3_ID_ISI 37 /* Image Sensor Interface */
+#define SAMA5D3_ID_SSC0 38 /* Synchronous Serial Controller 0 */
+#define SAMA5D3_ID_SSC1 39 /* Synchronous Serial Controller 1 */
+#define SAMA5D3_ID_CAN0 40 /* CAN Controller 0 */
+#define SAMA5D3_ID_CAN1 41 /* CAN Controller 1 */
+#define SAMA5D3_ID_SHA 42 /* Secure Hash Algorithm */
+#define SAMA5D3_ID_AES 43 /* Advanced Encryption Standard */
+#define SAMA5D3_ID_TDES 44 /* Triple Data Encryption Standard */
+#define SAMA5D3_ID_TRNG 45 /* True Random Generator Number */
+#define SAMA5D3_ID_IRQ0 47 /* Advanced Interrupt Controller (IRQ0) */
+
+/*
+ * Internal Memory
+ */
+#define SAMA5D3_SRAM_BASE 0x00300000 /* Internal SRAM base address */
+#define SAMA5D3_SRAM_SIZE (128 * SZ_1K) /* Internal SRAM size (128Kb) */
+
+#endif
diff --git a/arch/arm/mach-at91/sama5d3.c b/arch/arm/mach-at91/sama5d3.c
new file mode 100644
index 0000000..4012797
--- /dev/null
+++ b/arch/arm/mach-at91/sama5d3.c
@@ -0,0 +1,377 @@
+/*
+ * Chip-specific setup code for the SAMA5D3 family
+ *
+ * Copyright (C) 2013 Atmel,
+ * 2013 Ludovic Desroches <ludovic.desroches at atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+#include <linux/module.h>
+#include <linux/dma-mapping.h>
+
+#include <asm/irq.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <mach/sama5d3.h>
+#include <mach/at91_pmc.h>
+#include <mach/cpu.h>
+
+#include "soc.h"
+#include "generic.h"
+#include "clock.h"
+#include "sam9_smc.h"
+
+/* --------------------------------------------------------------------
+ * Clocks
+ * -------------------------------------------------------------------- */
+
+/*
+ * The peripheral clocks.
+ */
+
+static struct clk pioA_clk = {
+ .name = "pioA_clk",
+ .pid = SAMA5D3_ID_PIOA,
+ .type = CLK_TYPE_PERIPHERAL,
+};
+static struct clk pioB_clk = {
+ .name = "pioB_clk",
+ .pid = SAMA5D3_ID_PIOB,
+ .type = CLK_TYPE_PERIPHERAL,
+};
+static struct clk pioC_clk = {
+ .name = "pioC_clk",
+ .pid = SAMA5D3_ID_PIOC,
+ .type = CLK_TYPE_PERIPHERAL,
+};
+static struct clk pioD_clk = {
+ .name = "pioD_clk",
+ .pid = SAMA5D3_ID_PIOD,
+ .type = CLK_TYPE_PERIPHERAL,
+};
+static struct clk pioE_clk = {
+ .name = "pioE_clk",
+ .pid = SAMA5D3_ID_PIOE,
+ .type = CLK_TYPE_PERIPHERAL,
+};
+static struct clk usart0_clk = {
+ .name = "usart0_clk",
+ .pid = SAMA5D3_ID_USART0,
+ .type = CLK_TYPE_PERIPHERAL,
+ .div = AT91_PMC_PCR_DIV2,
+};
+static struct clk usart1_clk = {
+ .name = "usart1_clk",
+ .pid = SAMA5D3_ID_USART1,
+ .type = CLK_TYPE_PERIPHERAL,
+ .div = AT91_PMC_PCR_DIV2,
+};
+static struct clk usart2_clk = {
+ .name = "usart2_clk",
+ .pid = SAMA5D3_ID_USART2,
+ .type = CLK_TYPE_PERIPHERAL,
+ .div = AT91_PMC_PCR_DIV2,
+};
+static struct clk usart3_clk = {
+ .name = "usart3_clk",
+ .pid = SAMA5D3_ID_USART3,
+ .type = CLK_TYPE_PERIPHERAL,
+ .div = AT91_PMC_PCR_DIV2,
+};
+static struct clk uart0_clk = {
+ .name = "uart0_clk",
+ .pid = SAMA5D3_ID_UART0,
+ .type = CLK_TYPE_PERIPHERAL,
+ .div = AT91_PMC_PCR_DIV2,
+};
+static struct clk uart1_clk = {
+ .name = "uart1_clk",
+ .pid = SAMA5D3_ID_UART1,
+ .type = CLK_TYPE_PERIPHERAL,
+ .div = AT91_PMC_PCR_DIV2,
+};
+static struct clk twi0_clk = {
+ .name = "twi0_clk",
+ .pid = SAMA5D3_ID_TWI0,
+ .type = CLK_TYPE_PERIPHERAL,
+ .div = AT91_PMC_PCR_DIV2,
+};
+static struct clk twi1_clk = {
+ .name = "twi1_clk",
+ .pid = SAMA5D3_ID_TWI1,
+ .type = CLK_TYPE_PERIPHERAL,
+ .div = AT91_PMC_PCR_DIV2,
+};
+static struct clk twi2_clk = {
+ .name = "twi2_clk",
+ .pid = SAMA5D3_ID_TWI2,
+ .type = CLK_TYPE_PERIPHERAL,
+ .div = AT91_PMC_PCR_DIV2,
+};
+static struct clk mmc0_clk = {
+ .name = "mci0_clk",
+ .pid = SAMA5D3_ID_HSMCI0,
+ .type = CLK_TYPE_PERIPHERAL,
+};
+static struct clk mmc1_clk = {
+ .name = "mci1_clk",
+ .pid = SAMA5D3_ID_HSMCI1,
+ .type = CLK_TYPE_PERIPHERAL,
+};
+static struct clk mmc2_clk = {
+ .name = "mci2_clk",
+ .pid = SAMA5D3_ID_HSMCI2,
+ .type = CLK_TYPE_PERIPHERAL,
+};
+static struct clk spi0_clk = {
+ .name = "spi0_clk",
+ .pid = SAMA5D3_ID_SPI0,
+ .type = CLK_TYPE_PERIPHERAL,
+};
+static struct clk spi1_clk = {
+ .name = "spi1_clk",
+ .pid = SAMA5D3_ID_SPI1,
+ .type = CLK_TYPE_PERIPHERAL,
+};
+static struct clk tcb0_clk = {
+ .name = "tcb0_clk",
+ .pid = SAMA5D3_ID_TC0,
+ .type = CLK_TYPE_PERIPHERAL,
+ .div = AT91_PMC_PCR_DIV2,
+};
+static struct clk tcb1_clk = {
+ .name = "tcb1_clk",
+ .pid = SAMA5D3_ID_TC1,
+ .type = CLK_TYPE_PERIPHERAL,
+ .div = AT91_PMC_PCR_DIV2,
+};
+static struct clk adc_clk = {
+ .name = "adc_clk",
+ .pid = SAMA5D3_ID_ADC,
+ .type = CLK_TYPE_PERIPHERAL,
+ .div = AT91_PMC_PCR_DIV2,
+};
+static struct clk adc_op_clk = {
+ .name = "adc_op_clk",
+ .type = CLK_TYPE_PERIPHERAL,
+ .rate_hz = 5000000,
+};
+static struct clk dma0_clk = {
+ .name = "dma0_clk",
+ .pid = SAMA5D3_ID_DMA0,
+ .type = CLK_TYPE_PERIPHERAL,
+};
+static struct clk dma1_clk = {
+ .name = "dma1_clk",
+ .pid = SAMA5D3_ID_DMA1,
+ .type = CLK_TYPE_PERIPHERAL,
+};
+static struct clk uhphs_clk = {
+ .name = "uhphs",
+ .pid = SAMA5D3_ID_UHPHS,
+ .type = CLK_TYPE_PERIPHERAL,
+};
+static struct clk udphs_clk = {
+ .name = "udphs_clk",
+ .pid = SAMA5D3_ID_UDPHS,
+ .type = CLK_TYPE_PERIPHERAL,
+};
+/* gmac only for sama5d33, sama5d34, sama5d35 */
+static struct clk macb0_clk = {
+ .name = "macb0_clk",
+ .pid = SAMA5D3_ID_GMAC,
+ .type = CLK_TYPE_PERIPHERAL,
+};
+/* emac only for sama5d31, sama5d35 */
+static struct clk macb1_clk = {
+ .name = "macb1_clk",
+ .pid = SAMA5D3_ID_EMAC,
+ .type = CLK_TYPE_PERIPHERAL,
+};
+/* lcd only for sama5d31, sama5d33, sama5d34 */
+static struct clk lcdc_clk = {
+ .name = "lcdc_clk",
+ .pid = SAMA5D3_ID_LCDC,
+ .type = CLK_TYPE_PERIPHERAL,
+};
+/* isi only for sama5d33, sama5d35 */
+static struct clk isi_clk = {
+ .name = "isi_clk",
+ .pid = SAMA5D3_ID_ISI,
+ .type = CLK_TYPE_PERIPHERAL,
+};
+static struct clk can0_clk = {
+ .name = "can0_clk",
+ .pid = SAMA5D3_ID_CAN0,
+ .type = CLK_TYPE_PERIPHERAL,
+ .div = AT91_PMC_PCR_DIV2,
+};
+static struct clk can1_clk = {
+ .name = "can1_clk",
+ .pid = SAMA5D3_ID_CAN1,
+ .type = CLK_TYPE_PERIPHERAL,
+ .div = AT91_PMC_PCR_DIV2,
+};
+static struct clk ssc0_clk = {
+ .name = "ssc0_clk",
+ .pid = SAMA5D3_ID_SSC0,
+ .type = CLK_TYPE_PERIPHERAL,
+ .div = AT91_PMC_PCR_DIV2,
+};
+static struct clk ssc1_clk = {
+ .name = "ssc1_clk",
+ .pid = SAMA5D3_ID_SSC1,
+ .type = CLK_TYPE_PERIPHERAL,
+ .div = AT91_PMC_PCR_DIV2,
+};
+static struct clk sha_clk = {
+ .name = "sha_clk",
+ .pid = SAMA5D3_ID_SHA,
+ .type = CLK_TYPE_PERIPHERAL,
+ .div = AT91_PMC_PCR_DIV8,
+};
+static struct clk aes_clk = {
+ .name = "aes_clk",
+ .pid = SAMA5D3_ID_AES,
+ .type = CLK_TYPE_PERIPHERAL,
+};
+static struct clk tdes_clk = {
+ .name = "tdes_clk",
+ .pid = SAMA5D3_ID_TDES,
+ .type = CLK_TYPE_PERIPHERAL,
+};
+
+static struct clk *periph_clocks[] __initdata = {
+ &pioA_clk,
+ &pioB_clk,
+ &pioC_clk,
+ &pioD_clk,
+ &pioE_clk,
+ &usart0_clk,
+ &usart1_clk,
+ &usart2_clk,
+ &usart3_clk,
+ &uart0_clk,
+ &uart1_clk,
+ &twi0_clk,
+ &twi1_clk,
+ &twi2_clk,
+ &mmc0_clk,
+ &mmc1_clk,
+ &mmc2_clk,
+ &spi0_clk,
+ &spi1_clk,
+ &tcb0_clk,
+ &tcb1_clk,
+ &adc_clk,
+ &adc_op_clk,
+ &dma0_clk,
+ &dma1_clk,
+ &uhphs_clk,
+ &udphs_clk,
+ &macb0_clk,
+ &macb1_clk,
+ &lcdc_clk,
+ &isi_clk,
+ &can0_clk,
+ &can1_clk,
+ &ssc0_clk,
+ &ssc1_clk,
+ &sha_clk,
+ &aes_clk,
+ &tdes_clk,
+};
+
+static struct clk pck0 = {
+ .name = "pck0",
+ .pmc_mask = AT91_PMC_PCK0,
+ .type = CLK_TYPE_PROGRAMMABLE,
+ .id = 0,
+};
+
+static struct clk pck1 = {
+ .name = "pck1",
+ .pmc_mask = AT91_PMC_PCK1,
+ .type = CLK_TYPE_PROGRAMMABLE,
+ .id = 1,
+};
+
+static struct clk pck2 = {
+ .name = "pck2",
+ .pmc_mask = AT91_PMC_PCK2,
+ .type = CLK_TYPE_PROGRAMMABLE,
+ .id = 2,
+};
+
+static struct clk_lookup periph_clocks_lookups[] = {
+ /* lookup table for DT entries */
+ CLKDEV_CON_DEV_ID("usart", "ffffee00.serial", &mck),
+ CLKDEV_CON_DEV_ID(NULL, "fffff200.gpio", &pioA_clk),
+ CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioB_clk),
+ CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioC_clk),
+ CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioD_clk),
+ CLKDEV_CON_DEV_ID(NULL, "fffffa00.gpio", &pioE_clk),
+ CLKDEV_CON_DEV_ID("usart", "f001c000.serial", &usart0_clk),
+ CLKDEV_CON_DEV_ID("usart", "f0020000.serial", &usart1_clk),
+ CLKDEV_CON_DEV_ID("usart", "f8020000.serial", &usart2_clk),
+ CLKDEV_CON_DEV_ID("usart", "f8024000.serial", &usart3_clk),
+ CLKDEV_CON_DEV_ID(NULL, "f0014000.i2c", &twi0_clk),
+ CLKDEV_CON_DEV_ID(NULL, "f0018000.i2c", &twi1_clk),
+ CLKDEV_CON_DEV_ID(NULL, "f801c000.i2c", &twi2_clk),
+ CLKDEV_CON_DEV_ID("mci_clk", "f0000000.mmc", &mmc0_clk),
+ CLKDEV_CON_DEV_ID("mci_clk", "f8000000.mmc", &mmc1_clk),
+ CLKDEV_CON_DEV_ID("mci_clk", "f8004000.mmc", &mmc2_clk),
+ CLKDEV_CON_DEV_ID("spi_clk", "f0004000.spi", &spi0_clk),
+ CLKDEV_CON_DEV_ID("spi_clk", "f8008000.spi", &spi1_clk),
+ CLKDEV_CON_DEV_ID("t0_clk", "f0010000.timer", &tcb0_clk),
+ CLKDEV_CON_DEV_ID("t0_clk", "f8014000.timer", &tcb1_clk),
+ CLKDEV_CON_DEV_ID("tsc_clk", "f8018000.tsadcc", &adc_clk),
+ CLKDEV_CON_DEV_ID("dma_clk", "ffffe600.dma-controller", &dma0_clk),
+ CLKDEV_CON_DEV_ID("dma_clk", "ffffe800.dma-controller", &dma1_clk),
+ CLKDEV_CON_DEV_ID("hclk", "600000.ohci", &uhphs_clk),
+ CLKDEV_CON_DEV_ID("ohci_clk", "600000.ohci", &uhphs_clk),
+ CLKDEV_CON_DEV_ID("ehci_clk", "700000.ehci", &uhphs_clk),
+ CLKDEV_CON_DEV_ID("pclk", "500000.gadget", &udphs_clk),
+ CLKDEV_CON_DEV_ID("hclk", "500000.gadget", &utmi_clk),
+ CLKDEV_CON_DEV_ID("hclk", "f0028000.ethernet", &macb0_clk),
+ CLKDEV_CON_DEV_ID("pclk", "f0028000.ethernet", &macb0_clk),
+ CLKDEV_CON_DEV_ID("hclk", "f802c000.ethernet", &macb1_clk),
+ CLKDEV_CON_DEV_ID("pclk", "f802c000.ethernet", &macb1_clk),
+ CLKDEV_CON_DEV_ID("pclk", "f0008000.ssc", &ssc0_clk),
+ CLKDEV_CON_DEV_ID("pclk", "f000c000.ssc", &ssc1_clk),
+ CLKDEV_CON_DEV_ID("can_clk", "f000c000.can", &can0_clk),
+ CLKDEV_CON_DEV_ID("can_clk", "f8010000.can", &can1_clk),
+ CLKDEV_CON_DEV_ID("sha_clk", "f8034000.sha", &sha_clk),
+ CLKDEV_CON_DEV_ID("aes_clk", "f8038000.aes", &aes_clk),
+ CLKDEV_CON_DEV_ID("tdes_clk", "f803c000.tdes", &tdes_clk),
+};
+
+static void __init sama5d3_register_clocks(void)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
+ clk_register(periph_clocks[i]);
+
+ clkdev_add_table(periph_clocks_lookups,
+ ARRAY_SIZE(periph_clocks_lookups));
+
+ clk_register(&pck0);
+ clk_register(&pck1);
+ clk_register(&pck2);
+}
+
+/* --------------------------------------------------------------------
+ * AT91SAM9x5 processor initialization
+ * -------------------------------------------------------------------- */
+
+static void __init sama5d3_map_io(void)
+{
+ at91_init_sram(0, SAMA5D3_SRAM_BASE, SAMA5D3_SRAM_SIZE);
+}
+
+AT91_SOC_START(sama5d3)
+ .map_io = sama5d3_map_io,
+ .register_clocks = sama5d3_register_clocks,
+AT91_SOC_END
diff --git a/arch/arm/mach-at91/setup.c b/arch/arm/mach-at91/setup.c
index 4b67847..2ecd169 100644
--- a/arch/arm/mach-at91/setup.c
+++ b/arch/arm/mach-at91/setup.c
@@ -151,6 +151,11 @@ static void __init soc_detect(u32 dbgu_base)
at91_soc_initdata.type = AT91_SOC_SAM9N12;
at91_boot_soc = at91sam9n12_soc;
break;
+
+ case ARCH_ID_SAMA5D3:
+ at91_soc_initdata.type = AT91_SOC_SAMA5D3;
+ at91_boot_soc = sama5d3_soc;
+ break;
}
/* at91sam9g10 */
@@ -206,6 +211,23 @@ static void __init soc_detect(u32 dbgu_base)
break;
}
}
+
+ if (at91_soc_initdata.type == AT91_SOC_SAMA5D3) {
+ switch (at91_soc_initdata.exid) {
+ case ARCH_EXID_SAMA5D31:
+ at91_soc_initdata.subtype = AT91_SOC_SAMA5D31;
+ break;
+ case ARCH_EXID_SAMA5D33:
+ at91_soc_initdata.subtype = AT91_SOC_SAMA5D33;
+ break;
+ case ARCH_EXID_SAMA5D34:
+ at91_soc_initdata.subtype = AT91_SOC_SAMA5D34;
+ break;
+ case ARCH_EXID_SAMA5D35:
+ at91_soc_initdata.subtype = AT91_SOC_SAMA5D35;
+ break;
+ }
+ }
}
static const char *soc_name[] = {
@@ -219,6 +241,7 @@ static const char *soc_name[] = {
[AT91_SOC_SAM9RL] = "at91sam9rl",
[AT91_SOC_SAM9X5] = "at91sam9x5",
[AT91_SOC_SAM9N12] = "at91sam9n12",
+ [AT91_SOC_SAMA5D3] = "sama5d3",
[AT91_SOC_NONE] = "Unknown"
};
@@ -241,6 +264,10 @@ static const char *soc_subtype_name[] = {
[AT91_SOC_SAM9X35] = "at91sam9x35",
[AT91_SOC_SAM9G25] = "at91sam9g25",
[AT91_SOC_SAM9X25] = "at91sam9x25",
+ [AT91_SOC_SAMA5D31] = "sama5d31",
+ [AT91_SOC_SAMA5D33] = "sama5d33",
+ [AT91_SOC_SAMA5D34] = "sama5d34",
+ [AT91_SOC_SAMA5D35] = "sama5d35",
[AT91_SOC_SUBTYPE_NONE] = "Unknown"
};
diff --git a/arch/arm/mach-at91/soc.h b/arch/arm/mach-at91/soc.h
index f3d3502..43a225f 100644
--- a/arch/arm/mach-at91/soc.h
+++ b/arch/arm/mach-at91/soc.h
@@ -22,6 +22,7 @@ extern struct at91_init_soc at91sam9g45_soc;
extern struct at91_init_soc at91sam9rl_soc;
extern struct at91_init_soc at91sam9x5_soc;
extern struct at91_init_soc at91sam9n12_soc;
+extern struct at91_init_soc sama5d3_soc;
#define AT91_SOC_START(_name) \
struct at91_init_soc __initdata _name##_soc \
@@ -68,3 +69,7 @@ static inline int at91_soc_is_enabled(void)
#if !defined(CONFIG_SOC_AT91SAM9N12)
#define at91sam9n12_soc at91_boot_soc
#endif
+
+#if !defined(CONFIG_SOC_SAMA5D3)
+#define sama5d3_soc at91_boot_soc
+#endif
--
1.7.11.3
More information about the linux-arm-kernel
mailing list