[PATCH 1/3] arm: kirkwood: affect pins to their devices on OpenBlocks A6
Andrew Lunn
andrew at lunn.ch
Wed Mar 6 13:21:31 EST 2013
On Wed, Mar 06, 2013 at 05:23:39PM +0100, Thomas Petazzoni wrote:
> The pinctrl configuration done for the Kirkwood-based OpenBlocks A6
> board was somewhat strange: all pins for all devices were selected
> through "hogs", i.e as pins of the pinctrl device. Even though it
> works, it isn't the proper way of doing things: pins should preferably
> be associated to whatever device they belong to.
Hi Thomas
Being able to add pinctrl nodes to the device is new. I think it was
added in 3.8. Before then each device driver had to explicitly request
its pins and most didn't, so hogs was the way to do it. Now the core
driver code gets the pins. So i would not say it is odd, just
outdated. It would be nice to change the comment to reflect this.
> Therefore, this patch moves the selection of pin muxing of the
> relevant pins to the UART nodes, the I2C node, the NAND node and the
> gpio-leds node.
For gpio-leds, see the comment i just made for the next patch.
Otherwise this look O.K.
Andrew
>
> Signed-off-by: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
> ---
> arch/arm/boot/dts/kirkwood-openblocks_a6.dts | 19 +++++++++++++------
> 1 file changed, 13 insertions(+), 6 deletions(-)
>
> diff --git a/arch/arm/boot/dts/kirkwood-openblocks_a6.dts b/arch/arm/boot/dts/kirkwood-openblocks_a6.dts
> index ede7fe0d..087681d 100644
> --- a/arch/arm/boot/dts/kirkwood-openblocks_a6.dts
> +++ b/arch/arm/boot/dts/kirkwood-openblocks_a6.dts
> @@ -19,17 +19,23 @@
> ocp at f1000000 {
> serial at 12000 {
> clock-frequency = <200000000>;
> + pinctrl-0 = <&pmx_uart0>;
> + pinctrl-names = "default";
> status = "ok";
> };
>
> serial at 12100 {
> clock-frequency = <200000000>;
> + pinctrl-0 = <&pmx_uart1>;
> + pinctrl-names = "default";
> status = "ok";
> };
>
> nand at 3000000 {
> chip-delay = <25>;
> status = "okay";
> + pinctrl-0 = <&pmx_nand>;
> + pinctrl-names = "default";
>
> partition at 0 {
> label = "uboot";
> @@ -69,6 +75,8 @@
>
> i2c at 11100 {
> status = "okay";
> + pinctrl-0 = <&pmx_twsi1>;
> + pinctrl-names = "default";
>
> s35390a: s35390a at 30 {
> compatible = "s35390a";
> @@ -77,16 +85,12 @@
> };
>
> pinctrl: pinctrl at 10000 {
> - pinctrl-0 = < &pmx_nand &pmx_uart0
> - &pmx_uart1 &pmx_twsi1
> - &pmx_dip_sw0 &pmx_dip_sw1
> + pinctrl-0 = <&pmx_dip_sw0 &pmx_dip_sw1
> &pmx_dip_sw2 &pmx_dip_sw3
> &pmx_gpio_0 &pmx_gpio_1
> &pmx_gpio_2 &pmx_gpio_3
> &pmx_gpio_4 &pmx_gpio_5
> - &pmx_gpio_6 &pmx_gpio_7
> - &pmx_led_red &pmx_led_green
> - &pmx_led_yellow >;
> + &pmx_gpio_6 &pmx_gpio_7>;
> pinctrl-names = "default";
>
> pmx_uart0: pmx-uart0 {
> @@ -195,6 +199,9 @@
>
> gpio-leds {
> compatible = "gpio-leds";
> + pinctrl-0 = <&pmx_led_red &pmx_led_green
> + &pmx_led_yellow>;
> + pinctrl-names = "default";
>
> led-red {
> label = "obsa6:red:stat";
> --
> 1.7.9.5
>
More information about the linux-arm-kernel
mailing list