[PATCH 11/14] ARM: OMAP2+: Add device-tree support for NOR flash

[Mark Jackson]

On 06/03/13 10:23, Mark Jackson wrote:
> On 05/03/13 21:34, Jon Hunter wrote:
>>
>> On 03/05/2013 11:30 AM, Jon Hunter wrote:
>>> On 03/05/2013 10:20 AM, Mark Jackson wrote:
>>
>> [snip]
>>
>>>> But I can see in physmap_of.c that the device gets registered without any call to
>>>> devm_pinctrl_get_select_default() and hence no probe deferring takes place is the
>>>> pinctrl device hasn't yet been started (which it hasn't).
>>>>
>>>> Does probe deferral need adding to physmap_of.c, or should the pinctrl device really
>>>> be registered sooner ?
>>>
>>> I see, so the pinctrl driver is not getting probed until later.
>>
>> Can you give this version of the patch a go? I have re-worked the patch
>> so the NOR device will only be registered after the GPMC probe completes.
>>
>> By the way, with this version you should remove "simple-bus" from your
>> gpmc node compatible strings. I now call of_platform_device_create() to
>> create the child device during the GPMC probe. I think that this is a
>> safer approach.
> 
> This is better in that the probe *is* now delayed until the gpmc has been setup,
> but I still get an oops.
> 
> However, this time it's in the actual cfi query code.
> 
> I've traced it down to when it tries to physically access the memory associated
> with the chip select in question (in this case CS3 @ 0x1a000000).
> 
> I printed some debug info to show that the GPMC CONFIG7 register is being setup
> correctly, and I show the physical to virtual memory mapping values, as performed
> in of_flash_probe(), but when I try to do a test raw_readw() on the virtual address,
> I get the following:-
> 
> [    1.222950] omap-gpmc 50000000.gpmc: GPMC revision 6.0
> [    1.229002] gpmc_read_settings_dt: read/write wait monitoring not enabled!
> [    1.237916] enabling NAND BCH ecc with 8-bit correction
> [    1.243843] ONFI param page 0 valid
> [    1.247531] ONFI flash detected
> [    1.250856] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP), 256MiB, page size: 2048, OOB size: 64
> [    1.263149] 8 ofpart partitions found on MTD device omap2-nand.0
> [    1.269492] Creating 8 MTD partitions on "omap2-nand.0":
> [    1.275150] 0x000000000000-0x000000020000 : "spl1"
> [    1.282593] 0x000000020000-0x000000040000 : "spl2"
> [    1.288524] 0x000000040000-0x000000060000 : "spl3"
> [    1.294456] 0x000000060000-0x000000080000 : "spl4"
> [    1.300270] 0x000000080000-0x0000001e0000 : "boot"
> [    1.307224] 0x0000001e0000-0x000000200000 : "env"
> [    1.313093] 0x000000200000-0x000004200000 : "rootfs"
> [    1.373589] 0x000004200000-0x000010000000 : "data"
> [    1.541884] gpmc_probe_nor_child 1
> [    1.545483] GPMC_CS_CONFIG7_0 : 00000f48
> [    1.549621] GPMC_CS_CONFIG7_1 : 00000f58
> [    1.553812] GPMC_CS_CONFIG7_2 : 00000f00
> [    1.557951] GPMC_CS_CONFIG7_3 : 00000c5a

0x00000c5a is an invalid mode !!

I'm trying to use a 64MB address space but not on a 64MB boundary ... oops.