[PATCH] mmc: sdhci-s3c: let device core setup the default pin configuration
Thomas Abraham
thomas.abraham at linaro.org
Wed Mar 6 06:36:16 EST 2013
With device core now able to setup the default pin configuration,
the call to devm_pinctrl_get_select_default can be removed. And
the pin configuration code based on the deprecated Samsung specific
gpio bindings is also removed.
Signed-off-by: Thomas Abraham <thomas.abraham at linaro.org>
---
.../devicetree/bindings/mmc/samsung-sdhci.txt | 35 +---------
drivers/mmc/host/sdhci-s3c.c | 71 ++-----------------
2 files changed, 12 insertions(+), 94 deletions(-)
diff --git a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt
index 3b3a1ee..328e990 100644
--- a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt
+++ b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt
@@ -5,13 +5,6 @@ MMC, SD and eMMC storage mediums. This file documents differences between the
core mmc properties described by mmc.txt and the properties used by the
Samsung implmentation of the SDHCI controller.
-Note: The mmc core bindings documentation states that if none of the core
-card-detect bindings are used, then the standard sdhci card detect mechanism
-is used. The Samsung's SDHCI controller bindings extends this as listed below.
-
-[A] The property "samsung,cd-pinmux-gpio" can be used as stated in the
- "Optional Board Specific Properties" section below.
-
Required SoC Specific Properties:
- compatible: should be one of the following
- "samsung,s3c6410-sdhci": For controllers compatible with s3c6410 sdhci
@@ -20,18 +13,8 @@ Required SoC Specific Properties:
controller.
Required Board Specific Properties:
-- Samsung GPIO variant (will be completely replaced by pinctrl):
- - gpios: Should specify the gpios used for clock, command and data lines. The
- gpio specifier format depends on the gpio controller.
-- Pinctrl variant (preferred if available):
- - pinctrl-0: Should specify pin control groups used for this controller.
- - pinctrl-names: Should contain only one value - "default".
-
-Optional Board Specific Properties:
-- samsung,cd-pinmux-gpio: Specifies the card detect line that is routed
- through a pinmux to the card-detect pin of the card slot. This property
- should be used only if none of the mmc core card-detect properties are
- used. Only for Samsung GPIO variant.
+- pinctrl-0: Should specify pin control groups used for this controller.
+- pinctrl-names: Should contain only one value - "default".
Example:
sdhci at 12530000 {
@@ -39,19 +22,9 @@ Example:
reg = <0x12530000 0x100>;
interrupts = <0 75 0>;
bus-width = <4>;
- cd-gpios = <&gpk2 2 2 3 3>;
-
- /* Samsung GPIO variant */
- gpios = <&gpk2 0 2 0 3>, /* clock line */
- <&gpk2 1 2 0 3>, /* command line */
- <&gpk2 3 2 3 3>, /* data line 0 */
- <&gpk2 4 2 3 3>, /* data line 1 */
- <&gpk2 5 2 3 3>, /* data line 2 */
- <&gpk2 6 2 3 3>; /* data line 3 */
-
- /* Pinctrl variant */
- pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4>;
+ cd-gpios = <&gpk2 2 0>;
pinctrl-names = "default";
+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4>;
};
Note: This example shows both SoC specific and board specific properties
diff --git a/drivers/mmc/host/sdhci-s3c.c b/drivers/mmc/host/sdhci-s3c.c
index 7363efe..86e0bd7 100644
--- a/drivers/mmc/host/sdhci-s3c.c
+++ b/drivers/mmc/host/sdhci-s3c.c
@@ -24,7 +24,6 @@
#include <linux/of_gpio.h>
#include <linux/pm.h>
#include <linux/pm_runtime.h>
-#include <linux/pinctrl/consumer.h>
#include <linux/mmc/host.h>
@@ -45,7 +44,6 @@
* @ioarea: The resource created when we claimed the IO area.
* @pdata: The platform data for this controller.
* @cur_clk: The index of the current bus clock.
- * @gpios: List of gpio numbers parsed from device tree.
* @clk_io: The clock for the internal bus interface.
* @clk_bus: The clocks that are available for the SD/MMC bus clock.
*/
@@ -57,8 +55,6 @@ struct sdhci_s3c {
unsigned int cur_clk;
int ext_cd_irq;
int ext_cd_gpio;
- int *gpios;
- struct pinctrl *pctrl;
struct clk *clk_io;
struct clk *clk_bus[MAX_BUS_CLK];
@@ -447,88 +443,39 @@ static int sdhci_s3c_parse_dt(struct device *dev,
struct device_node *node = dev->of_node;
struct sdhci_s3c *ourhost = to_s3c(host);
u32 max_width;
- int gpio, cnt, ret;
+ int gpio;
/* if the bus-width property is not specified, assume width as 1 */
if (of_property_read_u32(node, "bus-width", &max_width))
max_width = 1;
pdata->max_width = max_width;
- ourhost->gpios = devm_kzalloc(dev, NUM_GPIOS(pdata->max_width) *
- sizeof(int), GFP_KERNEL);
- if (!ourhost->gpios)
- return -ENOMEM;
-
/* get the card detection method */
if (of_get_property(node, "broken-cd", NULL)) {
pdata->cd_type = S3C_SDHCI_CD_NONE;
- goto setup_bus;
+ return 0;
}
if (of_get_property(node, "non-removable", NULL)) {
pdata->cd_type = S3C_SDHCI_CD_PERMANENT;
- goto setup_bus;
+ return 0;
}
gpio = of_get_named_gpio(node, "cd-gpios", 0);
if (gpio_is_valid(gpio)) {
pdata->cd_type = S3C_SDHCI_CD_GPIO;
- goto found_cd;
- } else if (gpio != -ENOENT) {
- dev_err(dev, "invalid card detect gpio specified\n");
- return -EINVAL;
- }
-
- gpio = of_get_named_gpio(node, "samsung,cd-pinmux-gpio", 0);
- if (gpio_is_valid(gpio)) {
- pdata->cd_type = S3C_SDHCI_CD_INTERNAL;
- goto found_cd;
- } else if (gpio != -ENOENT) {
- dev_err(dev, "invalid card detect gpio specified\n");
- return -EINVAL;
- }
-
- /* assuming internal card detect that will be configured by pinctrl */
- pdata->cd_type = S3C_SDHCI_CD_INTERNAL;
- goto setup_bus;
-
- found_cd:
- if (pdata->cd_type == S3C_SDHCI_CD_GPIO) {
pdata->ext_cd_gpio = gpio;
ourhost->ext_cd_gpio = -1;
if (of_get_property(node, "cd-inverted", NULL))
pdata->ext_cd_gpio_invert = 1;
- } else if (pdata->cd_type == S3C_SDHCI_CD_INTERNAL) {
- ret = devm_gpio_request(dev, gpio, "sdhci-cd");
- if (ret) {
- dev_err(dev, "card detect gpio request failed\n");
- return -EINVAL;
- }
- ourhost->ext_cd_gpio = gpio;
- }
-
- setup_bus:
- if (!IS_ERR(ourhost->pctrl))
return 0;
-
- /* get the gpios for command, clock and data lines */
- for (cnt = 0; cnt < NUM_GPIOS(pdata->max_width); cnt++) {
- gpio = of_get_gpio(node, cnt);
- if (!gpio_is_valid(gpio)) {
- dev_err(dev, "invalid gpio[%d]\n", cnt);
- return -EINVAL;
- }
- ourhost->gpios[cnt] = gpio;
- }
-
- for (cnt = 0; cnt < NUM_GPIOS(pdata->max_width); cnt++) {
- ret = devm_gpio_request(dev, ourhost->gpios[cnt], "sdhci-gpio");
- if (ret) {
- dev_err(dev, "gpio[%d] request failed\n", cnt);
- return -EINVAL;
- }
+ } else if (gpio != -ENOENT) {
+ dev_err(dev, "invalid card detect gpio specified\n");
+ return -EINVAL;
}
+ /* assuming internal card detect that will be configured by pinctrl */
+ pdata->cd_type = S3C_SDHCI_CD_INTERNAL;
return 0;
}
#else
@@ -589,8 +536,6 @@ static int sdhci_s3c_probe(struct platform_device *pdev)
goto err_pdata_io_clk;
}
- sc->pctrl = devm_pinctrl_get_select_default(&pdev->dev);
-
if (pdev->dev.of_node) {
ret = sdhci_s3c_parse_dt(&pdev->dev, host, pdata);
if (ret)
--
1.6.6.rc2
More information about the linux-arm-kernel
mailing list