[PATCH 11/14] ARM: OMAP2+: Add device-tree support for NOR flash

Jon Hunter jon-hunter at ti.com
Tue Mar 5 12:30:19 EST 2013


On 03/05/2013 10:20 AM, Mark Jackson wrote:
> On 05/03/13 14:46, Jon Hunter wrote:
>>
>> On 03/05/2013 08:34 AM, Mark Jackson wrote:
>>> On 26/02/13 17:30, Jon Hunter wrote:
>>>> NOR flash is not currently supported when booting with device-tree
>>>> on OMAP2+ devices. Add support to detect and configure NOR devices
>>>> when booting with device-tree.
>>>>
>>>> Add documentation for the TI GPMC NOR binding.
>>>>
>>>> Signed-off-by: Jon Hunter <jon-hunter at ti.com>
>>>
>>> I'm trying to test this series, and am unable get my NOR device recognised.
>>>
>>> If I remove all reference to NOR (and keep only my NAND device definition), then
>>> everything seems to boot fine (so I'm assuming I've got at least the basics of
>>> the patch set working).
>>>
>>> My GPMC tree looks like this:-
> 
> <snip>
> 
>>> 	nor at 1,0 {
>>> 		reg = <3 0x00000000 0x04000000>;
>>> 		compatible = "cfi-flash";
>>> 		linux,mtd-name = "spansion,s29gl064n90t";
>>> 		bank-width = <2>;
>>>
>>> 		gpmc,device-width = <1>;
>>
>> Only bank-width should be necessary for NOR (per the binding
>> documentation). However, if you do specify both, then they should match.
>> Do you have two 8-bits devices? If so may be I need to update the
>> documentation to make it clear this is the total width of all devices
>> for a given chip-select.
> 
> No ... that was wrong, so I've fixed that.

Ok, I may update the documentation to make this clearer anyway.

> <snip>
> 
>>> Booting with this NOR device produces the following oops:-
>>>
>>> [    0.000000] Booting Linux on physical CPU 0x0
>>> [    0.000000] Linux version 3.9.0-rc1-12191-ga00d6d1-dirty (mpfj at mpfj-nanobone) (gcc version 4.5.4 (Buildroot 2012.11) ) #33 Tue Mar 5 13:08:25 GMT 2013
>>> [    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d
> 
> <snip>
> 
>>> [    0.236730] omap-gpmc 50000000.gpmc: could not find pctldev for node /pinmux at 44e10800/gpmc_pins, deferring probe
>>> [    0.236781] platform 50000000.gpmc: Driver omap-gpmc requests probe deferral
>>
>> This look like your problem. I would figure out why this is failing and
>> try again.
> 
> Hmmmm ... I get this even when I've no NOR device defined and the board boots up fine.

So for NAND, the device does not get registered until the GPMC probe
completes. However, in the case of NOR, DT is registering the GPMC
and its child devices and so it is working slightly different in
this case.

> But I can see in physmap_of.c that the device gets registered without any call to
> devm_pinctrl_get_select_default() and hence no probe deferring takes place is the
> pinctrl device hasn't yet been started (which it hasn't).
>
> Does probe deferral need adding to physmap_of.c, or should the pinctrl device really
> be registered sooner ?

I see, so the pinctrl driver is not getting probed until later.

This really highlights a weakness in the GPMC driver, particularly
for NOR, where the child device can only be probed once the parent
is probed. I don't see this as being DT specific issue, because
even on older OMAP boards we always registered the NOR flash device
independently of the GPMC device. So we have always been susceptible to
this problem AFAICT.

This is admittedly a hack, but I am curious if you add the pinctrl
properties to the NOR node, if this would also defer the probe on the
NOR device?

Ideally it would be great to defer the probing of the child until the
parent has been probed successfully.

Cheers
Jon



More information about the linux-arm-kernel mailing list