[PATCH V3 1/2] Phy: Exynos: Add Exynos5250 sata phy driver
Yuvaraj Kumar
yuvaraj.cd at gmail.com
Mon Dec 30 04:53:57 EST 2013
Thanks for the review.
On Mon, Dec 30, 2013 at 12:14 PM, Kishon Vijay Abraham I <kishon at ti.com> wrote:
> Hi,
>
>
> On Tuesday 10 December 2013 03:35 PM, Yuvaraj Kumar C D wrote:
>>
>> This patch adds the sata phy driver for Exynos5250.Exynos5250 sata
>> phy comprises of CMU and TRSV blocks which are of I2C register Map.
>> So this patch also adds a i2c client driver, which is used configure
>> the CMU and TRSV block of exynos5250 SATA PHY.
>>
>> This patch incorporates the generic phy framework to deal with sata
>> phy.
>>
>> This patch depends on the below patches
>> [1].drivers: phy: add generic PHY framework
>> by Kishon Vijay Abraham I<kishon at ti.com>
>> [2].ata: ahci_platform: Manage SATA PHY
>> by Roger Quadros <rogerq at ti.com>
>>
>> Changes from V2:
>> 1.Removed of_match_table
>> 2.Moved to syscon interface for PMU handling.
>>
>> Changes from V1:
>> 1.Adapted to latest version of Generic PHY framework
>> 2.Removed exynos_sata_i2c_remove function.
>>
>> Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd at samsung.com>
>> Signed-off-by: Girish K S <ks.giri at samsung.com>
>> Signed-off-by: Vasanth Ananthan <vasanth.a at samsung.com>
>> ---
>> drivers/phy/Kconfig | 11 ++
>> drivers/phy/Makefile | 1 +
>> drivers/phy/exynos5250_phy_i2c.c | 44 ++++++++
>> drivers/phy/sata_phy_exynos5250.c | 219
>> +++++++++++++++++++++++++++++++++++++
>> drivers/phy/sata_phy_exynos5250.h | 35 ++++++
>> 5 files changed, 310 insertions(+)
>> create mode 100644 drivers/phy/exynos5250_phy_i2c.c
>> create mode 100644 drivers/phy/sata_phy_exynos5250.c
>> create mode 100644 drivers/phy/sata_phy_exynos5250.h
>>
>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
>> index a344f3d..54f9baf 100644
>> --- a/drivers/phy/Kconfig
>> +++ b/drivers/phy/Kconfig
>> @@ -51,4 +51,15 @@ config PHY_EXYNOS_DP_VIDEO
>> help
>> Support for Display Port PHY found on Samsung EXYNOS SoCs.
>>
>> +config EXYNOS5250_SATA_PHY
>> + tristate "Exynos5250 Sata SerDes/PHY driver"
>> + depends on SOC_EXYNOS5250
>> + select GENERIC_PHY
>> + select MFD_SYSCON if ARCH_EXYNOS5
>> + help
>> + Enable this to support SATA SerDes/Phy found on Samsung's
>> + Exynos5250 based SoCs.This SerDes/Phy supports SATA 1.5 Gb/s,
>> + SATA 3.0 Gb/s, SATA 6.0 Gb/s speeds.It supports one SATA host
>> + port to accept one SATA device.
>> +
>> endmenu
>> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
>> index d0caae9..af98f32 100644
>> --- a/drivers/phy/Makefile
>> +++ b/drivers/phy/Makefile
>> @@ -7,3 +7,4 @@ obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO) +=
>> phy-exynos-dp-video.o
>> obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO) += phy-exynos-mipi-video.o
>> obj-$(CONFIG_OMAP_USB2) += phy-omap-usb2.o
>> obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o
>> +obj-$(CONFIG_EXYNOS5250_SATA_PHY) += sata_phy_exynos5250.o
>> exynos5250_phy_i2c.o
>> diff --git a/drivers/phy/exynos5250_phy_i2c.c
>> b/drivers/phy/exynos5250_phy_i2c.c
>> new file mode 100644
>> index 0000000..c0c1150
>> --- /dev/null
>> +++ b/drivers/phy/exynos5250_phy_i2c.c
>> @@ -0,0 +1,44 @@
>> +/*
>> + * Copyright (C) 2013 Samsung Electronics Co.Ltd
>> + * Author:
>> + * Yuvaraj C D <yuvaraj.cd at samsung.com>
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> it
>> + * under the terms of the GNU General Public License as published by
>> the
>> + * Free Software Foundation; either version 2 of the License, or (at
>> your
>> + * option) any later version.
>> + *
>> + */
>> +
>> +#include <linux/i2c.h>
>> +#include <linux/kernel.h>
>> +#include <linux/module.h>
>> +#include "sata_phy_exynos5250.h"
>> +
>> +static int exynos_sata_i2c_probe(struct i2c_client *client,
>> + const struct i2c_device_id *i2c_id)
>> +{
>> + int ret = 0;
>> + ret = sataphy_attach_i2c_client(client);
>> + if (ret < 0)
>> + return ret;
>> +
>> + dev_info(&client->adapter->dev,
>> + "attached %s into sataphy i2c adapter successfully\n",
>> + client->name);
>> +
>> + return ret;
>> +}
>> +
>> +static const struct i2c_device_id sataphy_i2c_device_match[] = {
>> + { "exynos-sataphy-i2c", 0 },
>> +};
>> +
>> +struct i2c_driver sataphy_i2c_driver = {
>> + .probe = exynos_sata_i2c_probe,
>> + .id_table = sataphy_i2c_device_match,
>> + .driver = {
>> + .name = "exynos-sataphy-i2c",
>> + .owner = THIS_MODULE,
>> + },
>> +};
>> diff --git a/drivers/phy/sata_phy_exynos5250.c
>> b/drivers/phy/sata_phy_exynos5250.c
>> new file mode 100644
>> index 0000000..b147119
>> --- /dev/null
>> +++ b/drivers/phy/sata_phy_exynos5250.c
>> @@ -0,0 +1,219 @@
>> +/*
>> + * Samsung SATA SerDes(PHY) driver
>> + *
>> + * Copyright (C) 2013 Samsung Electronics Co., Ltd.
>> + * Authors: Girish K S <ks.giri at samsung.com>
>> + * Yuvaraj Kumar C D <yuvaraj.cd at samsung.com>
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 as
>> + * published by the Free Software Foundation.
>> + */
>> +
>> +#include <linux/clk.h>
>> +#include <linux/delay.h>
>> +#include <linux/io.h>
>> +#include <linux/i2c.h>
>> +#include <linux/kernel.h>
>> +#include <linux/module.h>
>> +#include <linux/of.h>
>> +#include <linux/of_address.h>
>> +#include <linux/phy/phy.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/regmap.h>
>> +#include <linux/spinlock.h>
>> +#include <linux/mfd/syscon.h>
>> +#include "sata_phy_exynos5250.h"
>> +
>> +static struct i2c_client *phy_i2c_client;
>> +
>> +struct exynos_sata_phy {
>> + struct phy *phy;
>> + struct clk *phyclk;
>> + void __iomem *regs;
>> + void __iomem *pmureg;
>> +};
>> +
>> +static bool wait_for_reg_status(void __iomem *base, u32 reg, u32
>> checkbit,
>> + u32 status)
>> +{
>> + unsigned long timeout = jiffies + usecs_to_jiffies(1000);
>> + while (time_before(jiffies, timeout)) {
>> + if ((readl(base + reg) & checkbit) == status)
>> + return true;
>> + }
>> + return false;
>> +}
>> +
>> +int sataphy_attach_i2c_client(struct i2c_client *sata_phy)
>> +{
>> + if (!sata_phy)
>> + return -EPROBE_DEFER;
>> + else
>> + phy_i2c_client = sata_phy;
>> +
>> + return 0;
>> +}
>> +
>> +static int exynos_sata_phy_power_on(struct phy *phy)
>> +{
>> + struct exynos_sata_phy *sata_phy = phy_get_drvdata(phy);
>> +
>> + if (sata_phy->pmureg)
>> + regmap_update_bits(sata_phy->pmureg,
>> SATAPHY_CONTROL_OFFSET,
>> + EXYNOS5_SATAPHY_PMU_ENABLE, EXYNOS_SATA_PHY_EN);
>> +
>> + return 0;
>> +}
>> +
>> +static int exynos_sata_phy_power_off(struct phy *phy)
>> +{
>> + struct exynos_sata_phy *sata_phy = phy_get_drvdata(phy);
>> +
>> + if (sata_phy->pmureg)
>> + regmap_update_bits(sata_phy->pmureg,
>> SATAPHY_CONTROL_OFFSET,
>> + EXYNOS5_SATAPHY_PMU_ENABLE, ~EXYNOS_SATA_PHY_EN);
>> +
>> + return 0;
>> +}
>> +
>> +static int exynos_sata_phy_init(struct phy *phy)
>> +{
>> + u32 val = 0;
>> + int ret = 0;
>> + u8 buf[] = { 0x3A, 0x0B };
>> + struct exynos_sata_phy *sata_phy = phy_get_drvdata(phy);
>> +
>> + if (sata_phy->pmureg)
>> + regmap_update_bits(sata_phy->pmureg,
>> SATAPHY_CONTROL_OFFSET,
>> + EXYNOS5_SATAPHY_PMU_ENABLE, EXYNOS_SATA_PHY_EN);
>> +
>> + writel(val, sata_phy->regs + EXYNOS5_SATA_RESET);
>> +
>> + val = readl(sata_phy->regs + EXYNOS5_SATA_RESET);
>> + val |= 0xFF;
>> + writel(val, sata_phy->regs + EXYNOS5_SATA_RESET);
>> +
>> + val = readl(sata_phy->regs + EXYNOS5_SATA_RESET);
>> + val |= LINK_RESET;
>> + writel(val, sata_phy->regs + EXYNOS5_SATA_RESET);
>> +
>> + val = readl(sata_phy->regs + EXYNOS5_SATA_RESET);
>> + val |= RESET_CMN_RST_N;
>> + writel(val, sata_phy->regs + EXYNOS5_SATA_RESET);
>> + val = readl(sata_phy->regs + EXYNOS5_SATA_PHSATA_CTRLM);
>> + val &= ~PHCTRLM_REF_RATE;
>> + writel(val, sata_phy->regs + EXYNOS5_SATA_PHSATA_CTRLM);
>> +
>> + /* High speed enable for Gen3 */
>> + val = readl(sata_phy->regs + EXYNOS5_SATA_PHSATA_CTRLM);
>> + val |= PHCTRLM_HIGH_SPEED;
>> + writel(val, sata_phy->regs + EXYNOS5_SATA_PHSATA_CTRLM);
>> +
>> + val |= CTRL0_P0_PHY_CALIBRATED_SEL | CTRL0_P0_PHY_CALIBRATED;
>> + writel(val, sata_phy->regs + EXYNOS5_SATA_CTRL0);
>> +
>> + writel(0x2, sata_phy->regs + EXYNOS5_SATA_MODE0);
>> +
>> + ret = i2c_master_send(phy_i2c_client, buf, sizeof(buf));
>> + if (ret < 0)
>> + return -ENXIO;
>> +
>> + /* release cmu reset */
>> + val = readl(sata_phy->regs + EXYNOS5_SATA_RESET);
>> + val &= ~RESET_CMN_RST_N;
>> + writel(val, sata_phy->regs + EXYNOS5_SATA_RESET);
>> +
>> + val = readl(sata_phy->regs + EXYNOS5_SATA_RESET);
>> + val |= RESET_CMN_RST_N;
>> + writel(val, sata_phy->regs + EXYNOS5_SATA_RESET);
>> +
>> + return (wait_for_reg_status(sata_phy->regs,
>> EXYNOS5_SATA_PHSATA_STATM,
>> + PHSTATM_PLL_LOCKED, 1)) ? 0 : -EINVAL;
>> +
>> +}
>> +
>> +static struct phy_ops exynos_sata_phy_ops = {
>> + .init = exynos_sata_phy_init,
>> + .power_on = exynos_sata_phy_power_on,
>> + .power_off = exynos_sata_phy_power_off,
>> + .owner = THIS_MODULE,
>> +};
>> +
>> +static int exynos_sata_phy_probe(struct platform_device *pdev)
>> +{
>> + struct exynos_sata_phy *sata;
>> + struct device *dev = &pdev->dev;
>> + struct resource *res;
>> + struct phy_provider *phy_provider;
>> + int ret = 0;
>> +
>> + sata = devm_kzalloc(dev, sizeof(*sata), GFP_KERNEL);
>> + if (!sata)
>> + return -ENOMEM;
>> +
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> +
>> + sata->regs = devm_ioremap_resource(dev, res);
>> + if (IS_ERR(sata->regs))
>> + return PTR_ERR(sata->regs);
>> +
>> + sata->pmureg = syscon_regmap_lookup_by_phandle(dev->of_node,
>> + "samsung,syscon-phandle");
>> + if (!sata->pmureg) {
>> + dev_err(dev, "syscon regmap lookup failed.\n");
>> + return PTR_ERR(sata->pmureg);
>> + }
>> + dev_set_drvdata(dev, sata);
>> +
>> + if (i2c_add_driver(&sataphy_i2c_driver)) {
>> + dev_err(dev, "failed to register sataphy i2c driver\n");
>> + return -ENOENT;
>> + }
>> +
>> + sata->phyclk = devm_clk_get(dev, "sata_phyctrl");
>> + if (IS_ERR(sata->phyclk)) {
>> + dev_err(dev, "failed to get clk for PHY\n");
>> + return PTR_ERR(sata->phyclk);
>> + }
>> +
>> + ret = clk_prepare_enable(sata->phyclk);
>> + if (ret < 0) {
>> + dev_err(dev, "failed to enable source clk\n");
>> + return ret;
>> + }
>> +
>> + phy_provider = devm_of_phy_provider_register(dev,
>> + of_phy_simple_xlate);
>> + if (IS_ERR(phy_provider))
>> + return PTR_ERR(phy_provider);
>> +
>> + sata->phy = devm_phy_create(dev, &exynos_sata_phy_ops, NULL);
>> + if (IS_ERR(sata->phy)) {
>> + dev_err(dev, "failed to create PHY\n");
>> + return PTR_ERR(sata->phy);
>> + }
>
>
> Recently Felipe found a problem that might arise if phy_create is called
> after phy_provider_register. Always do phy_provider_register as the last
> step.
Ok.
>
>> + phy_set_drvdata(sata->phy, sata);
>> + return 0;
>> +}
>> +
>> +static const struct of_device_id exynos_sata_phy_of_match[] = {
>> + { .compatible = "samsung,exynos5250-sata-phy" },
>> + { },
>> +};
>> +MODULE_DEVICE_TABLE(of, exynos_sata_phy_of_match);
>> +
>> +static struct platform_driver exynos_sata_phy_driver = {
>> + .probe = exynos_sata_phy_probe,
>> + .driver = {
>> + .of_match_table = exynos_sata_phy_of_match,
>> + .name = "samsung,sata-phy",
>> + .owner = THIS_MODULE,
>> + }
>> +};
>> +module_platform_driver(exynos_sata_phy_driver);
>> +
>> +MODULE_DESCRIPTION("Samsung SerDes PHY driver");
>> +MODULE_LICENSE("GPL");
>> +MODULE_AUTHOR("ks.giri <ks.giri at samsung.com>");
>> +MODULE_AUTHOR("Yuvaraj C D <yuvaraj.cd at samsung.com>");
>> diff --git a/drivers/phy/sata_phy_exynos5250.h
>> b/drivers/phy/sata_phy_exynos5250.h
>> new file mode 100644
>> index 0000000..3e2089d
>> --- /dev/null
>> +++ b/drivers/phy/sata_phy_exynos5250.h
>> @@ -0,0 +1,35 @@
>> +/*
>> + *
>> + * Copyright (c) 2013 Samsung Electronics Co., Ltd.
>> + * Author:
>> + * Yuvaraj Kumar C D<yuvaraj.cd at samsung.com>
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> it
>> + * under the terms of the GNU General Public License as published by
>> the
>> + * Free Software Foundation; either version 2 of the License, or (at
>> your
>> + * option) any later version.
>> + */
>> +
>> +#define EXYNOS5_SATA_RESET 0x4
>> +#define EXYNOS5_SATA_MODE0 0x10
>> +#define EXYNOS5_SATA_CTRL0 0x14
>> +#define EXYNOS5_SATA_STAT0 0x18
>> +#define EXYNOS5_SATA_PHSATA_CTRLM 0xE0
>> +#define EXYNOS5_SATA_PHSATA_CTRL0 0xE4
>> +#define EXYNOS5_SATA_PHSATA_STATM 0xF0
>> +#define EXYNOS5_SATA_PHSTAT0 0xF4
>> +
>> +#define RESET_CMN_RST_N (1 << 1)
>> +#define LINK_RESET 0xF0000
>> +#define CTRL0_P0_PHY_CALIBRATED_SEL (1 << 9)
>> +#define CTRL0_P0_PHY_CALIBRATED (1 << 8)
>> +#define PHCTRLM_REF_RATE (1 << 1)
>> +#define PHCTRLM_HIGH_SPEED (1 << 0)
>> +#define PHSTATM_PLL_LOCKED (1 << 0)
>> +#define SATA_PHY_CON_RESET (LINK_RESET | 3F)
>> +#define EXYNOS_SATA_PHY_EN (1 << 0)
>> +#define SATAPHY_CONTROL_OFFSET 0x0724
>> +#define EXYNOS5_SATAPHY_PMU_ENABLE (1 << 0)
>> +
>> +int sataphy_attach_i2c_client(struct i2c_client *sata_phy);
>> +extern struct i2c_driver sataphy_i2c_driver;
>
>
> extern not needed here. Checkpatch should have shown a warning here no?
No, Checkpatch didnt shown any warning.
extern is needed here. struct sataphy_i2c_driver is declared in
exynos5250_phy_i2c.c but used in
sata_phy_exynos5250.c to register as an i2c driver.Without extern this
wont compile.
>
> Apart from these two comments, I think this patch is ready to be merged.
>
> Cheers,
> Kishon
>>
>>
>
More information about the linux-arm-kernel
mailing list