[PATCH 1/5] input: Add new sun4i-ts driver for Allwinner sunxi SoC's rtp controller
Hans de Goede
hdegoede at redhat.com
Tue Dec 24 17:24:03 EST 2013
Note the sun4i-ts controller is capable of detecting a second touch, but when
a second touch is present then the accuracy becomes so bad the reported touch
location is not useable.
The original android driver contains some complicated heuristics using the
aprox. distance between the 2 touches to see if the user is making a pinch
open / close movement, and then reports emulated multi-touch events around
the last touch coordinate (as the dual-touch coordinates are worthless).
These kinds of heuristics are just asking for trouble (and don't belong
in the kernel). So this driver offers straight forward, reliable single
touch functionality only.
Signed-off-by: Hans de Goede <hdegoede at redhat.com>
---
drivers/input/touchscreen/Kconfig | 10 ++
drivers/input/touchscreen/Makefile | 1 +
drivers/input/touchscreen/sun4i-ts.c | 272 +++++++++++++++++++++++++++++++++++
3 files changed, 283 insertions(+)
create mode 100644 drivers/input/touchscreen/sun4i-ts.c
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index 961d58d..95023de 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -906,6 +906,16 @@ config TOUCHSCREEN_STMPE
To compile this driver as a module, choose M here: the
module will be called stmpe-ts.
+config TOUCHSCREEN_SUN4I
+ tristate "Allwinner sun4i resistive touchscreen controller support"
+ depends on ARCH_SUNXI
+ help
+ This selects support for the resistive touchscreen controller
+ found on Allwinner sunxi SoCs.
+
+ To compile this driver as a module, choose M here: the
+ module will be called sun4i-ts.
+
config TOUCHSCREEN_SUR40
tristate "Samsung SUR40 (Surface 2.0/PixelSense) touchscreen"
depends on USB
diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
index 62801f2..c8f7375 100644
--- a/drivers/input/touchscreen/Makefile
+++ b/drivers/input/touchscreen/Makefile
@@ -54,6 +54,7 @@ obj-$(CONFIG_TOUCHSCREEN_PIXCIR) += pixcir_i2c_ts.o
obj-$(CONFIG_TOUCHSCREEN_S3C2410) += s3c2410_ts.o
obj-$(CONFIG_TOUCHSCREEN_ST1232) += st1232.o
obj-$(CONFIG_TOUCHSCREEN_STMPE) += stmpe-ts.o
+obj-$(CONFIG_TOUCHSCREEN_SUN4I) += sun4i-ts.o
obj-$(CONFIG_TOUCHSCREEN_SUR40) += sur40.o
obj-$(CONFIG_TOUCHSCREEN_TI_AM335X_TSC) += ti_am335x_tsc.o
obj-$(CONFIG_TOUCHSCREEN_TNETV107X) += tnetv107x-ts.o
diff --git a/drivers/input/touchscreen/sun4i-ts.c b/drivers/input/touchscreen/sun4i-ts.c
new file mode 100644
index 0000000..b3f01c0
--- /dev/null
+++ b/drivers/input/touchscreen/sun4i-ts.c
@@ -0,0 +1,272 @@
+/*
+ * sun4i-ts.c Allwinner sunxi resistive touchscreen controller driver
+ *
+ * Copyright (C) 2013 - 2014 Hans de Goede <hdegoede at redhat.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/*
+ * The sun4i-ts controller is capable of detecting a second touch, but when a
+ * second touch is present then the accuracy becomes so bad the reported touch
+ * location is not useable.
+ *
+ * The original android driver contains some complicated heuristics using the
+ * aprox. distance between the 2 touches to see if the user is making a pinch
+ * open / close movement, and then reports emulated multi-touch events around
+ * the last touch coordinate (as the dual-touch coordinates are worthless).
+ *
+ * These kinds of heuristics are just asking for trouble (and don't belong
+ * in the kernel). So this driver offers straight forward, reliable single
+ * touch functionality only.
+ */
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/input.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#define TP_CTRL0 0x00
+#define TP_CTRL1 0x04
+#define TP_CTRL2 0x08
+#define TP_CTRL3 0x0c
+#define TP_INT_FIFOC 0x10
+#define TP_INT_FIFOS 0x14
+#define TP_TPR 0x18
+#define TP_CDAT 0x1c
+#define TEMP_DATA 0x20
+#define TP_DATA 0x24
+
+/* TP_CTRL0 bits */
+#define ADC_FIRST_DLY(x) ((x) << 24) /* 8 bits */
+#define ADC_FIRST_DLY_MODE(x) ((x) << 23)
+#define ADC_CLK_SEL(x) ((x) << 22)
+#define ADC_CLK_DIV(x) ((x) << 20) /* 3 bits */
+#define FS_DIV(x) ((x) << 16) /* 4 bits */
+#define T_ACQ(x) ((x) << 0) /* 16 bits */
+
+/* TP_CTRL1 bits */
+#define STYLUS_UP_DEBOUN(x) ((x) << 12) /* 8 bits */
+#define STYLUS_UP_DEBOUN_EN(x) ((x) << 9)
+#define TOUCH_PAN_CALI_EN(x) ((x) << 6)
+#define TP_DUAL_EN(x) ((x) << 5)
+#define TP_MODE_EN(x) ((x) << 4)
+#define TP_ADC_SELECT(x) ((x) << 3)
+#define ADC_CHAN_SELECT(x) ((x) << 0) /* 3 bits */
+
+/* TP_CTRL2 bits */
+#define TP_SENSITIVE_ADJUST(x) ((x) << 28) /* 4 bits */
+#define TP_MODE_SELECT(x) ((x) << 26) /* 2 bits */
+#define PRE_MEA_EN(x) ((x) << 24)
+#define PRE_MEA_THRE_CNT(x) ((x) << 0) /* 24 bits */
+
+/* TP_CTRL3 bits */
+#define FILTER_EN(x) ((x) << 2)
+#define FILTER_TYPE(x) ((x) << 0) /* 2 bits */
+
+/* TP_INT_FIFOC irq and fifo mask / control bits */
+#define TEMP_IRQ_EN(x) ((x) << 18)
+#define OVERRUN_IRQ_EN(x) ((x) << 17)
+#define DATA_IRQ_EN(x) ((x) << 16)
+#define TP_DATA_XY_CHANGE(x) ((x) << 13)
+#define FIFO_TRIG(x) ((x) << 8) /* 5 bits */
+#define DATA_DRQ_EN(x) ((x) << 7)
+#define FIFO_FLUSH(x) ((x) << 4)
+#define TP_UP_IRQ_EN(x) ((x) << 1)
+#define TP_DOWN_IRQ_EN(x) ((x) << 0)
+
+/* TP_INT_FIFOS irq and fifo status bits */
+#define TEMP_DATA_PENDING (1 << 18)
+#define FIFO_OVERRUN_PENDING (1 << 17)
+#define FIFO_DATA_PENDING (1 << 16)
+#define TP_IDLE_FLG (1 << 2)
+#define TP_UP_PENDING (1 << 1)
+#define TP_DOWN_PENDING (1 << 0)
+
+struct sun4i_ts_data {
+ struct device *dev;
+ void __iomem *base;
+ struct input_dev *input;
+ int ignore_fifo_data;
+};
+
+static irqreturn_t sun4i_ts_irq(int irq, void *dev_id)
+{
+ struct sun4i_ts_data *ts = dev_id;
+ u32 reg_val, x, y;
+
+ reg_val = readl(ts->base + TP_INT_FIFOS);
+
+ if (reg_val & FIFO_DATA_PENDING) {
+ x = readl(ts->base + TP_DATA);
+ y = readl(ts->base + TP_DATA);
+ /* The 1st location reported after an up event is unreliable */
+ if (!ts->ignore_fifo_data) {
+ input_report_abs(ts->input, ABS_X, x);
+ input_report_abs(ts->input, ABS_Y, y);
+ /*
+ * The hardware has a separate down status bit, but
+ * that gets set before we get the first location,
+ * resulting in reporting a click on the old location.
+ */
+ input_report_key(ts->input, BTN_TOUCH, 1);
+ input_sync(ts->input);
+ } else
+ ts->ignore_fifo_data = 0;
+ }
+
+ if (reg_val & TP_UP_PENDING) {
+ ts->ignore_fifo_data = 1;
+ input_report_key(ts->input, BTN_TOUCH, 0);
+ input_sync(ts->input);
+ }
+
+ writel(reg_val, ts->base + TP_INT_FIFOS);
+
+ return IRQ_HANDLED;
+}
+
+static int sun4i_ts_register_input(struct sun4i_ts_data *ts,
+ const char *name)
+{
+ int ret;
+ struct input_dev *input;
+
+ input = devm_input_allocate_device(ts->dev);
+ if (!input)
+ return -ENOMEM;
+
+ input->name = name;
+ input->phys = "sun4i_ts/input0";
+ input->id.bustype = BUS_HOST;
+ input->id.vendor = 0x0001;
+ input->id.product = 0x0001;
+ input->id.version = 0x0100;
+ input->dev.parent = ts->dev;
+ input->evbit[0] = BIT(EV_SYN) | BIT(EV_KEY) | BIT(EV_ABS);
+ set_bit(BTN_TOUCH, input->keybit);
+ input_set_abs_params(input, ABS_X, 0, 4095, 0, 0);
+ input_set_abs_params(input, ABS_Y, 0, 4095, 0, 0);
+
+ ret = input_register_device(input);
+ if (ret)
+ return ret;
+
+ ts->input = input;
+ return 0;
+}
+
+static int sun4i_ts_remove(struct platform_device *pdev)
+{
+ struct sun4i_ts_data *ts = platform_get_drvdata(pdev);
+
+ /* Deactivate all IRQs */
+ writel(0, ts->base + TP_INT_FIFOC);
+ msleep(20);
+
+ if (ts->input)
+ input_unregister_device(ts->input);
+
+ kfree(ts);
+
+ return 0;
+}
+
+static int sun4i_ts_probe(struct platform_device *pdev)
+{
+ struct sun4i_ts_data *ts;
+ int ret = -ENOMEM;
+
+ ts = kzalloc(sizeof(struct sun4i_ts_data), GFP_KERNEL);
+ if (!ts)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, ts);
+
+ ts->dev = &pdev->dev;
+ ts->base = devm_ioremap_resource(&pdev->dev,
+ platform_get_resource(pdev, IORESOURCE_MEM, 0));
+ if (IS_ERR(ts->base)) {
+ ret = PTR_ERR(ts->base);
+ goto error;
+ }
+
+ ret = devm_request_irq(&pdev->dev, platform_get_irq(pdev, 0),
+ sun4i_ts_irq, 0, "sun4i-ts", ts);
+ if (ret)
+ goto error;
+
+ ret = sun4i_ts_register_input(ts, pdev->name);
+ if (ret)
+ goto error;
+
+ /*
+ * Select HOSC clk, clkin = clk / 6, adc samplefreq = clkin / 8192,
+ * t_acq = clkin / (16 * 64)
+ */
+ writel(ADC_CLK_SEL(0) | ADC_CLK_DIV(2) | FS_DIV(7) | T_ACQ(63),
+ ts->base + TP_CTRL0);
+
+ /*
+ * sensitive_adjust = 15 : max, which is not all that sensitive,
+ * tp_mode = 0 : only x and y coordinates, as we don't use dual touch
+ */
+ writel(TP_SENSITIVE_ADJUST(15) | TP_MODE_SELECT(0),
+ ts->base + TP_CTRL2);
+
+ /* Enable median filter, type 1 : 5/3 */
+ writel(FILTER_EN(1) | FILTER_TYPE(1), ts->base + TP_CTRL3);
+
+ /* Flush fifo, set trig level to 1, enable data and pen up irqs */
+ writel(DATA_IRQ_EN(1) | FIFO_TRIG(1) | FIFO_FLUSH(1) | TP_UP_IRQ_EN(1),
+ ts->base + TP_INT_FIFOC);
+
+ /*
+ * Set stylus up debounce to aprox 10 ms, enable debounce, and
+ * finally enable tp mode.
+ */
+ writel(STYLUS_UP_DEBOUN(5) | STYLUS_UP_DEBOUN_EN(1) | TP_MODE_EN(1),
+ ts->base + TP_CTRL1);
+
+ return 0;
+
+error:
+ sun4i_ts_remove(pdev);
+ return ret;
+}
+
+static const struct of_device_id sun4i_ts_of_match[] = {
+ { .compatible = "allwinner,sun4i-ts", },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, sun4i_ts_of_match);
+
+static struct platform_driver sun4i_ts_driver = {
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = "sun4i-ts",
+ .of_match_table = of_match_ptr(sun4i_ts_of_match),
+ },
+ .probe = sun4i_ts_probe,
+ .remove = sun4i_ts_remove,
+};
+
+module_platform_driver(sun4i_ts_driver);
+
+MODULE_DESCRIPTION("Allwinner sun4i resistive touchscreen controller driver");
+MODULE_AUTHOR("Hans de Goede <hdegoede at redhat.com>");
+MODULE_LICENSE("GPL");
--
1.8.4.2
More information about the linux-arm-kernel
mailing list