[PATCH v4 2/4] pinctrl: Add pinctrl binding for Broadcom Capri SoCs
Sherman Yin
syin at broadcom.com
Fri Dec 20 21:13:34 EST 2013
Adds pinctrl driver devicetree binding for Broadcom Capri (BCM281xx) SoCs.
Signed-off-by: Sherman Yin <syin at broadcom.com>
Reviewed-by: Christian Daudt <bcm at fixthebug.org>
Reviewed-by: Matt Porter <matt.porter at linaro.org>
---
v4: Changed valid values for "bias-pull-up" property for I2C pins. Expanded
pin configuration node example.
v3: Use generic pin config properties instead of brcm-specific ones. Clarified
pin types (standard, i2c, hdmi).
v2: Use hyphens instead of underscore in DT property names.
---
.../bindings/pinctrl/brcm,capri-pinctrl.txt | 461 ++++++++++++++++++++
1 file changed, 461 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/brcm,capri-pinctrl.txt
diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,capri-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/brcm,capri-pinctrl.txt
new file mode 100644
index 0000000..9e9e9ef
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/brcm,capri-pinctrl.txt
@@ -0,0 +1,461 @@
+Broadcom Capri Pin Controller
+
+This is a pin controller for the Broadcom BCM281xx SoC family, which includes
+BCM11130, BCM11140, BCM11351, BCM28145, and BCM28155 SoCs.
+
+=== Pin Controller Node ===
+
+Required Properties:
+
+- compatible: Must be "brcm,capri-pinctrl".
+- reg: Base address of the PAD Controller register block and the size
+ of the block.
+
+For example, the following is the bare minimum node:
+
+ pinctrl at 35004800 {
+ compatible = "brcm,capri-pinctrl";
+ reg = <0x35004800 0x430>;
+ };
+
+As a pin controller device, in addition to the required properties, this node
+should also contain the pin configuration nodes that client devices reference,
+if any.
+
+=== Pin Configuration Node ===
+
+Each pin configuration node is a sub-node of the pin controller node and is a
+container of an arbitrary number of subnodes, called pin group nodes in this
+document.
+
+Please refer to the pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the definition of a
+"pin configuration node".
+
+=== Pin Group Node ===
+
+A pin group node specifies the desired pin mux and/or pin configuration for an
+arbitrary number of pins. The name of the pin group node is optional and not
+used.
+
+A pin group node only affects the properties specified in the node, and has no
+effect on any properties that are omitted.
+
+The pin group node accepts a subset of the generic pin config properties. For
+details generic pin config properties, please refer to pinctrl-bindings.txt
+and <include/linux/pinctrl/pinconfig-generic.h>.
+
+Each pin controlled by this pin controller belong to one of three types:
+Standard, I2C, and HDMI. Each type accepts a different set of pin config
+properties. A list of pins and their types is provided below.
+
+Required Properties (applicable to all pins):
+
+- pins: Multiple strings. Specifies the name(s) of one or more pins to
+ be configured by this node.
+
+Optional Properties (for standard pins):
+
+- function: String. Specifies the pin mux selection. Values
+ must be one of: "alt1", "alt2", "alt3", "alt4"
+- input-schmitt-enable: No arguments. Enable schmitt-trigger mode.
+- input-schmitt-disable: No arguments. Disable schmitt-trigger mode.
+- bias-pull-up: No arguments. Pull up on pin.
+- bias-pull-down: No arguments. Pull down on pin.
+- bias-disable: No arguments. Disable pin bias.
+- slew-rate: Integer. Meaning depends on configured pin mux:
+ *_SCL or *_SDA:
+ 0: Standard(100kbps)& Fast(400kbps) mode
+ 1: Highspeed (3.4Mbps) mode
+ IC_DM or IC_DP:
+ 0: normal slew rate
+ 1: fast slew rate
+ Otherwise:
+ 0: fast slew rate
+ 1: normal slew rate
+- input-enable: No arguements. Enable input (does not affect
+ output.)
+- input-disable: No arguements. Disable input (does not affect
+ output.)
+- drive-strength: Integer. Drive strength in mA. Valid values are
+ 2, 4, 6, 8, 10, 12, 14, 16 mA.
+
+Optional Properties (for I2C pins):
+
+- function: String. Specifies the pin mux selection. Values
+ must be one of: "alt1", "alt2", "alt3", "alt4"
+- bias-pull-up: Integer. Pull up strength in Ohm. There are 3
+ pull-up resisitors (1.2k, 1.8k, 2.7k) available
+ in parallel for I2C pins, so the valid values
+ are: 568, 720, 831, 1080, 1200, 1800, 2700 Ohm.
+- bias-disable: No arguments. Disable pin bias.
+- slew-rate: Integer. Meaning depends on configured pin mux:
+ *_SCL or *_SDA:
+ 0: Standard(100kbps)& Fast(400kbps) mode
+ 1: Highspeed (3.4Mbps) mode
+ IC_DM or IC_DP:
+ 0: normal slew rate
+ 1: fast slew rate
+ Otherwise:
+ 0: fast slew rate
+ 1: normal slew rate
+- input-enable: No arguements. Enable input (does not affect
+ output.)
+- input-disable: No arguements. Disable input (does not affect
+ output.)
+
+Optional Properties (for HDMI pins):
+
+- function: String. Specifies the pin mux selection. Values
+ must be one of: "alt1", "alt2", "alt3", "alt4"
+- slew-rate: Integer. Controls slew rate.
+ 0: Standard(100kbps)& Fast(400kbps) mode
+ 1: Highspeed (3.4Mbps) mode
+- input-enable: No arguements. Enable input (does not affect
+ output.)
+- input-disable: No arguements. Disable input (does not affect
+ output.)
+
+Example:
+// pin controller node
+pinctrl at 35004800 {
+ compatible = "brcm,capri-pinctrl";
+ reg = <0x35004800 0x430>;
+
+ // pin configuration node
+ dev_a_default: dev_a_active {
+ //group node defining 1 standard pin
+ grp_1 {
+ pins = "std_pin1";
+ function = "alt1";
+ input-schmitt-enable;
+ bias-disable;
+ slew-rate = <1>;
+ drive-strength = <4>;
+ };
+
+ // group node defining 2 I2C pins
+ grp_2 {
+ pins = "i2c_pin1", "i2c_pin2";
+ function = "alt2";
+ bias-pull-up = <720>;
+ input-enable;
+ };
+
+ // group node defining 2 HDMI pins
+ grp_3 {
+ pins = "hdmi_pin1", "hdmi_pin2";
+ function = "alt3";
+ slew-rate = <1>;
+ };
+
+ // other pin group nodes
+ ...
+ };
+
+ // other pin configuration nodes
+ ...
+};
+
+In the example above, "dev_a_active" is a pin configuration node with a number
+of sub-nodes. In the pin group node "grp_1", one pin, "std_pin1", is defined in
+the "pins" property. Thus, the remaining properties in the "grp_1" node applies
+only to this pin, including the following settings:
+ - setting pinmux to "alt1"
+ - enabling schmitt-trigger (hystersis) mode
+ - disabling pin bias
+ - setting the slew-rate to 1
+ - setting the drive strength to 4 mA
+Note that neither "input-enable" nor "input-disable" was specified - the pinctrl
+subsystem will therefore leave this property unchanged from whatever state it
+was in before applying these changes.
+
+The "pins" property in the pin group node "grp_2" specifies two pins -
+"i2c_pin1" and "i2c_pin2"; the remaining properties in this pin group node,
+therefore, applies to both of these pins. The properties include:
+ - setting pinmux to "alt2"
+ - setting pull-up resistance to 720 Ohm (ie. enabling 1.2k and 1.8k resistors
+ in parallel)
+ - enabling both pins' input
+"slew-rate" is not specified in this pin group node, so the slew-rate for these
+pins are left as-is.
+
+Finally, "grp_3" defines two HDMI pins. The following properties are applied to
+both pins:
+ - setting pinmux to "alt3"
+ - setting slew-rate to 1; for HDMI pins, this corresponds to the 3.4 Mbps
+ Highspeed mode
+The input is neither enabled or disabled, and is left untouched.
+
+=== Pin Names and Type ===
+
+The following are valid pin names and their pin types:
+
+ "adcsync", Standard
+ "bat_rm", Standard
+ "bsc1_scl", I2C
+ "bsc1_sda", I2C
+ "bsc2_scl", I2C
+ "bsc2_sda", I2C
+ "classgpwr", Standard
+ "clk_cx8", Standard
+ "clkout_0", Standard
+ "clkout_1", Standard
+ "clkout_2", Standard
+ "clkout_3", Standard
+ "clkreq_in_0", Standard
+ "clkreq_in_1", Standard
+ "cws_sys_req1", Standard
+ "cws_sys_req2", Standard
+ "cws_sys_req3", Standard
+ "digmic1_clk", Standard
+ "digmic1_dq", Standard
+ "digmic2_clk", Standard
+ "digmic2_dq", Standard
+ "gpen13", Standard
+ "gpen14", Standard
+ "gpen15", Standard
+ "gpio00", Standard
+ "gpio01", Standard
+ "gpio02", Standard
+ "gpio03", Standard
+ "gpio04", Standard
+ "gpio05", Standard
+ "gpio06", Standard
+ "gpio07", Standard
+ "gpio08", Standard
+ "gpio09", Standard
+ "gpio10", Standard
+ "gpio11", Standard
+ "gpio12", Standard
+ "gpio13", Standard
+ "gpio14", Standard
+ "gps_pablank", Standard
+ "gps_tmark", Standard
+ "hdmi_scl", HDMI
+ "hdmi_sda", HDMI
+ "ic_dm", Standard
+ "ic_dp", Standard
+ "kp_col_ip_0", Standard
+ "kp_col_ip_1", Standard
+ "kp_col_ip_2", Standard
+ "kp_col_ip_3", Standard
+ "kp_row_op_0", Standard
+ "kp_row_op_1", Standard
+ "kp_row_op_2", Standard
+ "kp_row_op_3", Standard
+ "lcd_b_0", Standard
+ "lcd_b_1", Standard
+ "lcd_b_2", Standard
+ "lcd_b_3", Standard
+ "lcd_b_4", Standard
+ "lcd_b_5", Standard
+ "lcd_b_6", Standard
+ "lcd_b_7", Standard
+ "lcd_g_0", Standard
+ "lcd_g_1", Standard
+ "lcd_g_2", Standard
+ "lcd_g_3", Standard
+ "lcd_g_4", Standard
+ "lcd_g_5", Standard
+ "lcd_g_6", Standard
+ "lcd_g_7", Standard
+ "lcd_hsync", Standard
+ "lcd_oe", Standard
+ "lcd_pclk", Standard
+ "lcd_r_0", Standard
+ "lcd_r_1", Standard
+ "lcd_r_2", Standard
+ "lcd_r_3", Standard
+ "lcd_r_4", Standard
+ "lcd_r_5", Standard
+ "lcd_r_6", Standard
+ "lcd_r_7", Standard
+ "lcd_vsync", Standard
+ "mdmgpio0", Standard
+ "mdmgpio1", Standard
+ "mdmgpio2", Standard
+ "mdmgpio3", Standard
+ "mdmgpio4", Standard
+ "mdmgpio5", Standard
+ "mdmgpio6", Standard
+ "mdmgpio7", Standard
+ "mdmgpio8", Standard
+ "mphi_data_0", Standard
+ "mphi_data_1", Standard
+ "mphi_data_2", Standard
+ "mphi_data_3", Standard
+ "mphi_data_4", Standard
+ "mphi_data_5", Standard
+ "mphi_data_6", Standard
+ "mphi_data_7", Standard
+ "mphi_data_8", Standard
+ "mphi_data_9", Standard
+ "mphi_data_10", Standard
+ "mphi_data_11", Standard
+ "mphi_data_12", Standard
+ "mphi_data_13", Standard
+ "mphi_data_14", Standard
+ "mphi_data_15", Standard
+ "mphi_ha0", Standard
+ "mphi_hat0", Standard
+ "mphi_hat1", Standard
+ "mphi_hce0_n", Standard
+ "mphi_hce1_n", Standard
+ "mphi_hrd_n", Standard
+ "mphi_hwr_n", Standard
+ "mphi_run0", Standard
+ "mphi_run1", Standard
+ "mtx_scan_clk", Standard
+ "mtx_scan_data", Standard
+ "nand_ad_0", Standard
+ "nand_ad_1", Standard
+ "nand_ad_2", Standard
+ "nand_ad_3", Standard
+ "nand_ad_4", Standard
+ "nand_ad_5", Standard
+ "nand_ad_6", Standard
+ "nand_ad_7", Standard
+ "nand_ale", Standard
+ "nand_cen_0", Standard
+ "nand_cen_1", Standard
+ "nand_cle", Standard
+ "nand_oen", Standard
+ "nand_rdy_0", Standard
+ "nand_rdy_1", Standard
+ "nand_wen", Standard
+ "nand_wp", Standard
+ "pc1", Standard
+ "pc2", Standard
+ "pmu_int", Standard
+ "pmu_scl", I2C
+ "pmu_sda", I2C
+ "rfst2g_mtsloten3g", Standard
+ "rgmii_0_rx_ctl", Standard
+ "rgmii_0_rxc", Standard
+ "rgmii_0_rxd_0", Standard
+ "rgmii_0_rxd_1", Standard
+ "rgmii_0_rxd_2", Standard
+ "rgmii_0_rxd_3", Standard
+ "rgmii_0_tx_ctl", Standard
+ "rgmii_0_txc", Standard
+ "rgmii_0_txd_0", Standard
+ "rgmii_0_txd_1", Standard
+ "rgmii_0_txd_2", Standard
+ "rgmii_0_txd_3", Standard
+ "rgmii_1_rx_ctl", Standard
+ "rgmii_1_rxc", Standard
+ "rgmii_1_rxd_0", Standard
+ "rgmii_1_rxd_1", Standard
+ "rgmii_1_rxd_2", Standard
+ "rgmii_1_rxd_3", Standard
+ "rgmii_1_tx_ctl", Standard
+ "rgmii_1_txc", Standard
+ "rgmii_1_txd_0", Standard
+ "rgmii_1_txd_1", Standard
+ "rgmii_1_txd_2", Standard
+ "rgmii_1_txd_3", Standard
+ "rgmii_gpio_0", Standard
+ "rgmii_gpio_1", Standard
+ "rgmii_gpio_2", Standard
+ "rgmii_gpio_3", Standard
+ "rtxdata2g_txdata3g1", Standard
+ "rtxen2g_txdata3g2", Standard
+ "rxdata3g0", Standard
+ "rxdata3g1", Standard
+ "rxdata3g2", Standard
+ "sdio1_clk", Standard
+ "sdio1_cmd", Standard
+ "sdio1_data_0", Standard
+ "sdio1_data_1", Standard
+ "sdio1_data_2", Standard
+ "sdio1_data_3", Standard
+ "sdio4_clk", Standard
+ "sdio4_cmd", Standard
+ "sdio4_data_0", Standard
+ "sdio4_data_1", Standard
+ "sdio4_data_2", Standard
+ "sdio4_data_3", Standard
+ "sim_clk", Standard
+ "sim_data", Standard
+ "sim_det", Standard
+ "sim_resetn", Standard
+ "sim2_clk", Standard
+ "sim2_data", Standard
+ "sim2_det", Standard
+ "sim2_resetn", Standard
+ "sri_c", Standard
+ "sri_d", Standard
+ "sri_e", Standard
+ "ssp_extclk", Standard
+ "ssp0_clk", Standard
+ "ssp0_fs", Standard
+ "ssp0_rxd", Standard
+ "ssp0_txd", Standard
+ "ssp2_clk", Standard
+ "ssp2_fs_0", Standard
+ "ssp2_fs_1", Standard
+ "ssp2_fs_2", Standard
+ "ssp2_fs_3", Standard
+ "ssp2_rxd_0", Standard
+ "ssp2_rxd_1", Standard
+ "ssp2_txd_0", Standard
+ "ssp2_txd_1", Standard
+ "ssp3_clk", Standard
+ "ssp3_fs", Standard
+ "ssp3_rxd", Standard
+ "ssp3_txd", Standard
+ "ssp4_clk", Standard
+ "ssp4_fs", Standard
+ "ssp4_rxd", Standard
+ "ssp4_txd", Standard
+ "ssp5_clk", Standard
+ "ssp5_fs", Standard
+ "ssp5_rxd", Standard
+ "ssp5_txd", Standard
+ "ssp6_clk", Standard
+ "ssp6_fs", Standard
+ "ssp6_rxd", Standard
+ "ssp6_txd", Standard
+ "stat_1", Standard
+ "stat_2", Standard
+ "sysclken", Standard
+ "traceclk", Standard
+ "tracedt00", Standard
+ "tracedt01", Standard
+ "tracedt02", Standard
+ "tracedt03", Standard
+ "tracedt04", Standard
+ "tracedt05", Standard
+ "tracedt06", Standard
+ "tracedt07", Standard
+ "tracedt08", Standard
+ "tracedt09", Standard
+ "tracedt10", Standard
+ "tracedt11", Standard
+ "tracedt12", Standard
+ "tracedt13", Standard
+ "tracedt14", Standard
+ "tracedt15", Standard
+ "txdata3g0", Standard
+ "txpwrind", Standard
+ "uartb1_ucts", Standard
+ "uartb1_urts", Standard
+ "uartb1_urxd", Standard
+ "uartb1_utxd", Standard
+ "uartb2_urxd", Standard
+ "uartb2_utxd", Standard
+ "uartb3_ucts", Standard
+ "uartb3_urts", Standard
+ "uartb3_urxd", Standard
+ "uartb3_utxd", Standard
+ "uartb4_ucts", Standard
+ "uartb4_urts", Standard
+ "uartb4_urxd", Standard
+ "uartb4_utxd", Standard
+ "vc_cam1_scl", I2C
+ "vc_cam1_sda", I2C
+ "vc_cam2_scl", I2C
+ "vc_cam2_sda", I2C
+ "vc_cam3_scl", I2C
+ "vc_cam3_sda", I2C
--
1.7.9.5
More information about the linux-arm-kernel
mailing list